Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Stanley SGT-25-450-H
- Page 1 Gasoline Tiller Original instructions SGT-25-450-H Gasoline Tiller...
- Page 2 Manufactured under license by: MATRIX GmbH Postauer Straße 26 D-84109 Wörth/Isar www.matrix-direct.net • • • Stanley is a registered trademark of The Stanley Works or its affiliates and is used under license.
-
Page 3: General Safety Rules
GENERAL SAFETY RULES • Before each use, always check to be sure that the tools are not worn out or damaged. When changing a worn-out or damaged component or ATTENTION: When using gasoline motors like this bolt, change all similar components out in order to one, basic safety rules must be observed in order preserve balance. -
Page 4: Preliminary Measures
HANDLING: • Allow the motor to cool off before storing it in any The engine must not be operated in enclosed enclosed space. areas in which carbon monoxide, a dangerous • To reduce risk of fire, keep the storage area for substance, could become concentrated. - Page 5 SYMBOLS Important: Do not wear loose clothing, neckties or jewelry (rings, wristwatches) when operating this machine. They may be Complies with appropriate safety caught by moving parts. standards. Keep bystanders away. Only operate the generator outside to ensure adequate ventilation. Do not smoke or have open flames Stay away from rotating augers.
-
Page 6: Contents Supplied
CONTENTS SUPPLIED fig.1 1.Tiller X1 14.Bolt M 8*70 X2 2.Girder X1 15.Hex flange face locknut M8 X5 3.Wheel assy X1 16.Bolt M 8*16 X2 4.Right blade cover X1 17.Flat washer D8 X3 5.Blade disc X2 18.Bolt M 6*35 X2 6.Resistance rod X1 19.Flat washer D6 X2 7.Safety plate X1 20.Hex locknut M6 X2... - Page 7 ASSEMBLY Following the assembly directions below, you will 14/15 assemble the front tine tiller in a few minutes. 1.Place tilling tines on the tine shaft on both sides of the gear box. Line up the holes in the tine frame sleeves and tine shaft.
- Page 8 15/21 fig.7 7. Install the Cable bandage(See Fig.8) fig.8 8. Mount the blade cover and tight it on the machine with 2x M 8*16 screws and flange locknuts.(See Fig.9) 15/16 fig.9 Engine oil Engine is shipped from factory without oil. You must add engine oil before...
- Page 10 LAYOUT 1. Handle 2. Gasoline engine 3. Blade cover 4.Blade disc 5. Wheel 6. Chain box 7. Blade 8. Resistance rod 9. Belt cover 10.Oil dispstick 11. Choke Lever 12.ON/OFF Switch 13.Recoiling Handle 14. Forward control rod 15. Reverse control rod 16.
- Page 11 in the area where gasoline is stored or where the fuel tank is refueled. 5) Check fuel lines, tank, cap and fittings frequently for cracks or leaks. Replace if necessary. 6) If fuel spill,wait until it evaporates before starting engine. fig.13 4) Pull the starting handle slowly until you feel the resistance, and then pull it out suddenly and...
- Page 12 tight or loose), the clutch may not work well. 1) Starting the engine. 2) Take the clutch control rod to the middle position. ( Figure 15) 3) Turn the adjusting nut in figure 16 in a clockwise direction to tighten the wheel clutch; or in a anticlockwise direction to loosen it.
-
Page 13: Maintenance
times. In later case, the depth regulator rod should 3. Remove all vegetation, string, wire, and other be lowered before each succeeding pass over the materials that may have accumulated to the garden. Passes should be made across the length axle between the inside set of tines and the and width of the garden alternately. - Page 14 Clean the air filter (Fig.20) O Seal Ring If the air cleaner is jam, it will output less enough air and cause fuel consumption increase. Check and clean it periodically. Cleaning Period: Once 50 hours’ working. If work in hervy dust area, check it every day or once 10 hours.
-
Page 15: Specification
cleaning plastic parts. Chemicals can damage plastics. 6. Inspect for any loose or damaged parts. Repair or replace damaged parts and tighten loose screws, nuts or bolts. 7. Remove the tines. Clean and apply oil to the tines and tine shafts to prevent rusting. Mount the tines onto the tine shafts. -
Page 16: Maintenance Schedule
Maintenance schedule Frequency Each time First Each Every 6 Each year month or season month or or 300hrs Items 20hrs or 50hrs 100 hrs ○ Engine Oil Oil level check ○ ○ Replace ○ Reduction Oil level Gear Oil check ○... -
Page 17: Troubleshooting
TROUBLE SHOOTING Problem Cause Remedy 1. Attach spark plug wire securely to spark plug. 1. Spark plug wire disconnected. 2.Fill with clean, fresh gasoline. 2.Out of fuel or stale fuel. 3. Move throttle control lever to start 3. Throttle control lever not in correct position. - Page 18 Postauer Str. 26 D-84109 Wörth/Isar Germany Fax: +49 (0) 8702/45338 98 E-Mail: info@matrix-direct.net hereby declares the following conformity under the EU Directive and standards for the following article Front Tine Tiller /SGT-25-450-H 2002/96/EC 2006/42/EC R&TTED 1999/5/EC 97/68/EC_2012/46/EC 93/68/EEC 2000/14/EC_2005/88/EC 2014/30/EU 97/68/EC_ 2004/26/EC EN 709;...
-
Page 19: Garantie
GARANTIE Guarantee This appliance is a quality product. It was designed in compliance with are excluded from the guarantee. Damages caused by the manufacturer or by a material defect will be corrected at no current technical standards and made carefully using normal, good quality charge by repair or by providing spare parts. - Page 20 Front Tine Tiller /SGT-25-450-H WARRANTY Purchased at: in (city, street): Name of customer: Street address: Postal code, city: Telephone: Date, signature: Fault description:...
Need help?
Do you have a question about the SGT-25-450-H and is the answer not in the manual?
Questions and answers