Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zte iCharge
Summary of Contents for Zte iCharge
- Page 1 Quick Start Guide...
-
Page 2: Getting To Know Your Device
Getting to Know Your Device Appearance The following figure is for your reference only. - Page 3 Indicator light Power key • Press and hold for about 3 seconds to power on/off your device. • Press and hold for about 15 seconds to restart your device. LAN/WAN port micro-SIM card slot and microSDHC™ card slot Reset key •...
-
Page 4: Indicator Lights
Getting to Know Your Device Indicator lights Description Status Indicator The battery level is too low, less than blinking 12%. Please charge the battery. The battery level is low, between 12% Red solid and 23%. Please charge the battery. Battery The battery level is Green middle or high, more... - Page 5 Blue solid Wi-Fi is active. Wi-Fi Blue WPS is active. blinking Light off Wi-Fi is off. You have unread Blue solid messages Blue You have new blinking messages. There is no unread Light off message or new message.
- Page 6 Error status. Not registered to the mobile network, no micro-SIM card inserted or no network service available. Registered to the Yellow 2G/3G mobile Network solid network. Connected to the Yellow 2G/3G mobile blinking network and data is being transferred. Green Registered to the LTE solid network...
-
Page 7: Connection Scenarios
Getting to Know Your Device Connection Scenarios The device can access the Internet in two ways and it allows multiple clients to surf on the Internet at the same time. And your device also can supply the power to other terminal devices micro-SIM Mode: Use a micro-SIM card to •... - Page 8 Ethernet Mode: Use the network cable to • connect your device to the Internet. Power Supply Mode: Your device can • supply power to other mobile devices...
- Page 9 Installing the micro-SIM Card and microSDHC Card Open the cover. NOTE: Do not remove the cover rudely, because it is connected with the device.
- Page 10 Install a micro-SIM card and a microSDHC card. WARNING! Your device does not support SIM cards and nano-SIM cards. To avoid damage to the device, do not use those cards or any card holders. Close the cover.
-
Page 11: Charging Your Device
Charging Your Device There are two methods to charge your device. • Use the power adapter to charge your device. • Use the USB port of the laptop or PC to charge your device. -
Page 12: Powering On Your Device
Powering on Your Device Press and hold the Power key for about 3 seconds to power on your device... -
Page 13: Connecting To Your Device
Connecting to Your Device Using Wi-Fi Choose Wi-Fi on your computer or other client devices, and search for available wireless networks. NOTE: Refer to your Wi-Fi-enabled client device manual for further details on how to search for wireless networks. If you use a computer, you need to set your computer to obtain an IP address automatically. -
Page 14: Using A Network Cable
Using a USB Cable Connect a computer to your device’s micro- USB jack with a USB cable. Power on your device. The operating system detects and identifies new hardware, and automatically installs the software. NOTE: If the system does not automatically launch installation, you can click the device installation icon in My Computer to install the software. - Page 15 Logging in to the etisalat 4G iCharge Configuration Page Launch the Internet browser and enter http://192.168.0.1 in the address bar. Enter the password to log in to the 4G Mobile Hotspot configuration page. NOTE: The default password is etisalat Acessing the internet...
- Page 16 Operation Your device is automatically connected to the Internet,and you Automatic can surf on the Internet through the client Log in to etisalat 4G iCharge configuration page. Select Network Settings> Connection Mode > Manual, Manual and then click Apply. Click...
-
Page 17: Accessing The Internet
Accessing the Internet Ethernet Mode Use the network cable to connect your device to the Internet. Log in to etisalat 4G iCharge configuration page. Select Wi-Fi Settings > Ethernet Settings. Select the Dial Mode and enter the detail parameters if necessary. - Page 18 Supplying Power to Other Mobile Device Use the USB cable to connect the USB port of your device to the other mobile device’s micro- USB jack and then power on your device. The following figure is for your reference only. NOTE: •...
- Page 19 Changing the Wi-Fi SSID or Password Log in to the etisalat 4G iCharge configuration page. Select Wi-Fi Settings. Change the Network Name (SSID) or the Password. Click Apply.
-
Page 20: Configuring Your Pc
Configuring Your PC The following procedure describes how to configure the Internet Protocol in Windows 7 for your Wi-Fi connection. Right-click Network and select Properties. Select Change adapter settings. Right-click Wireless Network Connection and select Properties. Select Internet Protocol Version 4 (TCP/ IPv4), and click Properties. -
Page 21: Warning And Notice
Warning and Notice To the Users: • If inadequately shielded, some electronic d ev i c e s , fo r exa m p l e , t h e e l e c t ro n i c system of vehicles, maybe affected by the electromagnetic interference caused by the device. - Page 22 explosive gases or explosive products being processed. Power off the device if necessary. • Do not use electronic transmission devices in aircrafts, at petrol stations or in hospitals. Observe and obey all warning signs, and power off the device in these conditions. •...
- Page 23 • When the device is operating, do not touch the metallic parts. Failing to do so may cause burns. • Use original accessories or accessories that are authorized. Using any unauthorized accessories may affect the performance of the device and violate the related national regulations about telecom terminals.
-
Page 24: Using Battery
• Handle the device carefully. Do not drop, bend or strike it. Otherwise the device may be damaged. • Only qualified personnel can dismantle and repair the device. • An operating temperature between -10°C and +60°C and humidity between 5% and 95% are recommended. - Page 25 iii. End users’ mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the product. Modifications or repairs not provided by etisalat or a etisalat-certified individual. Power failures, surges, fire, flood, accidents, and actions of third parties or other events outside etisalat’s reasonable control.
-
Page 26: Limitation Of Liability
T h i s w a r ra n t y i s e n d u s e r s ’ s o l e re m e d y and etisalat’s sole liability for defective or nonconforming items, and is in lieu of all other warranties, expressed, implied or statutory, including but not limited to the implied warranties of merchantability and fitness for a particular... -
Page 27: Legal Information
ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. -
Page 28: Troubleshooting
Troubleshooting Problem Recommended Action • Ensure that the Wi-Fi function is enabled. Refresh the network list and select the correct SSID. connection • Check the IP address, and between your ensure that your client can device and a automatically obtain an IP client through address. - Page 29 Problem Recommended Action • Ensure that your micro-SIM card is available. • Change the location and The client find a place with good connected to signal. the device • Check the settings of the cannot access connection mode. the Internet. •...
- Page 30 Problem Recommended Action • Enter the correct address. etisalat 4G The default address is iCharge http://192.168.0.1. configuration • Use only one network page cannot adapter in your PC. Do not be visited. use any proxy server • For the Wi-Fi connection password, view the label on the device.
-
Page 31: Getting More Help
Getting More Help You can get help by: • Sending an email to mobile@zte.com.cn • Visiting www.ztedevice.com • Calling the service hotline: +86-755-26779999...