StoneBilt Concepts Telluride Installation Instructions Manual

Gas fire pit

Advertisement

StoneBilt
Concepts®
recommends that this
product be installed by a qualified professional
WARNING: This fire pit is for outdoor use only. This fire
pit can produce carbon monoxide. Never use in an
enclosed space such as a home, tent or camper.
WARNING: IF YOU SMELL GAS: (1) Turn off the gas to the
unit. (2) Put out all open flames (3) If the smell continues
move away from the fire pit and call the Fire Department.
WARNING: Do not store gasoline or any flammable
liquids or vapors near the fire pit.
WARNING: For all gas connections that require thread
sealant use only products that are resistant to gases.
Apply to male pipe fittings only. DO NOT USE ON FLARED
FITTINGS
Never use any fuel , solid or gas, other than what is in-
tended by the burner. The fire pit can not be converted
for use with other fuel sources.
Do not place any object on the fire pit. Never place any
flammable materials near the fire pit when in use.
The fire pit can become very hot when in use. Keep away
from structures furniture, draperies or anything that
could be damaged by heat or flame.
Do not leave young children alone while the fire pit is in
use. Maintain adult supervision at all times to avoid any
accidents or injury.
StoneBilt Concepts
Gas Fire Pit

Installation Instructions

Equipped with the Crossfire™ Brass Burner System by
WARNING
SAFETY
Warming Trends™
WARNING: If not installed and maintained correctly this
product can cause property damage or injury. Do not
alter the provided equipment in any way.
WARNING: Use your fire pit responsibly. Check with your
local government for local codes and regulations before
installing your fire pit.
The Crossfire™ Burner is ICC certified and compiles with
ANSI Z21.97/CSA 2.41-2014 Outdoor Decorative Gas Ap-
pliances Standards.
Keep the area around the fir pit clean and uncluttered to
avoid injuries. Clear the area of any trip hazards.
Keep all combustible materials away from the fire pit
If a propane tank is used be sure to place the propane
tank at a safe distance away from the fire pit.
Read all instruction before installing the fire pit. This in-
cludes the Warming Trends Policy Manual Instructions.
Provided with your burner.
Telluride Gas Fire Pit. Page 1 of 7
®

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Telluride and is the answer not in the manual?

Questions and answers

Summary of Contents for StoneBilt Concepts Telluride

  • Page 1: Installation Instructions

    Telluride Gas Fire Pit. Page 1 of 7 StoneBilt Concepts ® Gas Fire Pit Installation Instructions Equipped with the Crossfire™ Brass Burner System by Warming Trends™ StoneBilt Concepts® recommends that this product be installed by a qualified professional WARNING WARNING: This fire pit is for outdoor use only. This fire pit can produce carbon monoxide.
  • Page 2 Telluride Gas Fire Pit. Page 2 of 7 These instructions are intended to be used in conjunction with the Warming Trends™ Installation Instructions available at StoneBiltConcepts.com. 1) Before beginning the installation of your fire pit it is important to take note of the provided parts list located on the last page of these instructions.
  • Page 3 Telluride Gas Fire Pit. Page 3 of 7 4) Now you can begin installing the Burner. Use a pipe wrench to tighten the 1/2” coupling to the 1/2” pipe extending from the back of the Valve Block. Then thread the Key Valve into the coupling and tighten with a wrench.
  • Page 4 Telluride Gas Fire Pit. Page 4 of 7 7) Apply thread sealant to one of the Male to Male Flare Fittings and attach to the outgoing end of the Key Valve. Tighten with a wrench. 8) Once the Male to Male Flare Fitting is securely in place, you can now attach the provided 36” Flex Line to the flare fitting.
  • Page 5 Telluride Gas Fire Pit. Page 5 of 7 10) Attach the 36” Flex Line to the flared fitting that is now attached to the burner. Tighten using a wrench. (Remember that no thread sealant is needed for flared fittings.) 11) The installer is responsible for checking all connections for any leaks. It is recommended that a leak test is performed before placing the cap stones on your fire pit.
  • Page 6 Telluride Gas Fire Pit. Page 6 of 7 14) Finally, use the provided 12” Valve Key to slowly turn the Key Valve on while holding a long match or lighter above the burner until it ignites. **Remember to test all connections for leaks before igniting your fire pit**...
  • Page 7: Parts List

    Telluride Gas Fire Pit. Page 7 of 7 Parts List 1/2” Coupling Drain Block Valve Block Key Valve Male to Male Flare Fitting X2 Propane Male Flare Fitting Propane Supply Line (Provided with propane fire pits) (Provided with propane fire pits) 12”...

Table of Contents