Related Manuals for TP-Link PSM150-AC
Summary of Contents for TP-Link PSM150-AC
-
Page 1: Installation Guide
Business Networking Solution Installation Guide 150W AC Power Supply Module PSM150-AC REV2.0.0 7106506700... -
Page 2: Chapter 1 Introduction
Chapter 1 Introduction 1.1 Overview of the Product The PSM150-AC is an AC-input and DC-output power supply module. It can convert the input voltage to 12 Volts with the maximum output power of 150 Watts. The power supply module is fully hot swappable, helping to ensure no system interruption during installation or replacement. - Page 3 1.2 Description of LEDs There are three LEDs on the front panel of PSM150-AC. Described below: LED Status Description Power On Power supply module is powered on and running well, but not PS OK Off supplying power to the switch.
- Page 4 In the case of 1+1 redundant power supply system, the Hot Swappable PSM150-AC can be plugged out or plugged in without shutting down the switch. Table 1-2 Features of PSM150-AC When the power module reverts to the protected state, its recovery characteristics are shown in Table 1-3.
-
Page 5: Chapter 2 Installation
Note: When the power supply module is locked or auto-retry continually, you can try the following steps to restore the device. Disconnect the power cord from the external power supply system. Disconnect the power cord from the power supply module. - Page 6 TP-Link, however, PSM150-AC can also support installation or removal when the AC power supply is 2.1 Safety Information To avoid damage to the power supply module and the equipment and bodily injury, please observe the following notes: •...
-
Page 7: Tools For Installation
2.2 Tools for Installation • Straight screwdriver • Philips screwdriver • ESD-preventive wrist strap 2.3 Installing & Removing the Power Supply Module • Installing the Power Supply Module Wear an ESD-preventive wrist strap, and make sure that it has good skin contact and is well grounded. Grip the handle of the module with one hand, and hold the bottom of the module using your other hand. - Page 8 • Removing the Power Supply Module Wear an ESD-preventive wrist strap, and make sure that it has good skin contact and is well grounded. Remove the power cord from the external power supply system and the power module. Use a Phillips screwdriver to loosen the captive screws at both sides of the power supply module until all spring pressure is released.
-
Page 9: Verifying The Installation
To verify the installation status of PSM150-AC, firstly, please make sure the two captive screws on PSM150-AC are tightened, then connect the power cord and check the LEDs of PSM150-AC. If the Power LED is on while Fault LED is off, it... - Page 10 AC power input is good and the device is working properly, and the installation of PSM150-AC has been successful.
- Page 11 Appendix: Specifications Item Specification AC Power Input 100V-240V～ 50/60Hz Output Voltage 12VDC Output Current 12.5A (Maximum) Output Power 150W (Maximum) Operation : 0°C to 40°C (32 to 104°F) Temperature Storage: -40°C to 70°C (-40 to 158°F) Operation : 20% to 90% RH Non-condensing Humidity Storage: 10% to 95% RH Non-condensing...
- Page 12 FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
-
Page 13: Bsmi Notice
product may cause radio interference, in which case the user may be required to take adequate measures. Industry Canada Statement CAN ICES-3 (A)/NMB-3(A) Korea Warning Statements 당해 무선설비는 운용중 전파혼신 가능성이 있음. BSMI Notice 安全諮詢及注意事項 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本 產品。 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或 濕布進行清潔。... - Page 14 Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України. Safety Information When product has power button, the power button is one of the way to shut off the product; When there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source.
- Page 15 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. © 2016 TP-Link...