Table of Contents
Advertisement
Quick Links
SCHMIDT MODEL G5 TAXIMETER
INSTALLATION INSTRUCTIONS
Contents
Contents
Contents
Contents
1. Wiring................................................................................................................................ 3
2. Installing the GPS Unit ...................................................................................................... 4
3. Installing the 3G Communications Module ........................................................................ 4
4. Installing the Bracket and Mounting the Taximeter ............................................................ 5
5. Clearing the G5 Taximeter Memory .................................................................................. 7
6. Manually Calibrating the G5 Taximeter ............................................................................. 8
7. Setting up the 3G Communications Port and Printer Port .................................................. 8
8. Assigning the G5 Taximeter to an Operator ...................................................................... 9
9. Create or Modify Taximeter Configuration ....................................................................... 10
10. Create or Modify Driver Users ....................................................................................... 11
11. Post Installation Checklist ............................................................................................. 11
12.Technical Assistance ..................................................................................................... 12
170516 G5 Installation Manual V4.docx
Version 5, 18 July 2017
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Schmidt G5
-
Page 1: Installation Instructions
6. Manually Calibrating the G5 Taximeter ................8 7. Setting up the 3G Communications Port and Printer Port ..........8 8. Assigning the G5 Taximeter to an Operator ..............9 9. Create or Modify Taximeter Configuration ............... 10 10. Create or Modify Driver Users ..................11 11. - Page 2 Figure 1: G5 Interface Box Wiring Diagram Cable (Supplied with G5 kit) terminated with RJ12 plug 5A Fuse GPS Receiver USB-C to USB-C Cable 12V Car Battery (Supplied with G5 kit) 3G Comms System Speedometer Wire RJ45 to RJ45 Cable (Supplied...
-
Page 3: Wiring
Connect a twisted two wire pair (with a 5 AMP fuse in line on the positive wire) from the battery to +12v and Gnd on the G5 Interface Box. Note: The G5 Interface Box provides two common +12V terminals and 3 common GND terminals. -
Page 4: Installing The Gps Unit
The G5 Interface Box connects with the 3G Communications Module using the USB port. Internal Fuse Inside the G5 Interface Box is a 5 AMP M205 fuse. This fuse is a final safeguard in case the fuse under the bonnet is bypassed. -
Page 5: Installing The Bracket And Mounting The Taximeter
4. Installing the Bracket and Mounting the Taximeter The G5 is supplied with a universal mounting kit that will allow it to be mounted in a variety of locations. With each kit you will receive the following: 1 x straight bracket... - Page 6 Figure 8: G5 Taximeter with sealing cover and screw Figure 10: Attach the Sealing Cover Figure 11: Seal the G5 Taximeter Display Unit Insert the M3 x 20mm slot head screw into the right side of the G5 Taximeter Display • Unit.
-
Page 7: Clearing The G5 Taximeter Memory
G5 Taximeter Interface Box. Figure 10: Attach the sealing cover Figure 11: Seal the interface box Ensure that the USB-C cable and the GPS are connected to the G5 Taximeter • Interface Box. Attach the G5 Taximeter Interface Box sealing cover. -
Page 8: Manually Calibrating The G5 Taximeter
The taximeter’s calibration, current time and current date will not be affected. 6. Manually Calibrating the G5 Taximeter Remove the G5 Taximeter Display Unit sealing cover. This reveals the USB port. • Insert the G5 Dealer Dongle into the USB Port. -
Page 9: Assigning The G5 Taximeter To An Operator
The G5 Taximeter must be assigned to an Operator. If the Operator is an existing customer who is already registered on the G5 Server, the Taximeter may be assigned to that Operator by a Dealer. If the Operator is not registered on the G5 Server, the Dealer needs to create an account for that Operator. -
Page 10: Create Or Modify Taximeter Configuration
If Mandate End of Shift Capture is selected, drivers will be required to enter data into the G5 Taximeter at the end of every shift. That data will be uploaded to the G5 Server. If this option is not selected, drivers will not be required to enter any end of shift data. -
Page 11: Create Or Modify Driver Users
6 different categories. The Operator can give these categories any name which is useful, e.g. EFTPOS, Dockets, Subsidy Scheme, etc. q. When the Save button is clicked this Taximeter Configuration will be saved on the G5 Server. The Operator may create an unlimited number of Taximeter Configurations, and he/she may select which Taximeter Configuration is applicable to which Taximeter at any time. -
Page 12: Technical Assistance
9. Check that the Printer is working correctly. If it is not working correctly, you may need to check or edit the PRINTER PORT or BAUD RATE. Refer to Section 7, above. 12.Technical Assistance If you have any questions regarding installation of the G5 Taximeter please contact our Technical Department on: +61 3 9546 6990...
Need help?
Do you have a question about the G5 and is the answer not in the manual?
Questions and answers