Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Broadcast Microwave Services Europe GmbH & Co. KG CT2020HD
- Page 1 ENGLISH (UK) REFERENCE GUIDE CT2020HD...
- Page 2 Si no entiende el contenido de este manual NO OPERE ESTE EQUIPO. Podemos asimismo suministrarle una traducción de este manual al (idioma) previo pago de una cantidad adicional que deberá abonar usted mismo. Reference Guide: CT2020HD Page ii March 08...
-
Page 3: List Of Contents
Preliminary Pages List of Contents Chapter 1: Introduction to the CT2020HD Gives a general description of the equipment and its main features and functions. Identifies the controls, indicators and connectors on the front and rear panels. Chapter 2: Installing the Equipment Provides a guide to the suitability of an installation and gives detailed procedures for the preparation and installation of the equipment. - Page 4 Customer Services and Technical Training Postal Address......x Return of Equipment ................x Technical Publications ................x Chapters 1 to 3 1. Introduction to the CT2020HD ............1 1.1 Preliminary Remarks ................ 1 1.2 Designation and P/N................. 1 1.3 Description ..................2 2.
- Page 5 Shock and Vibration ..............B-2 B.1.4 CE Marking ................B-2 B.1.5 FCC Marking ................B-2 Technical Specifications ..............B-3 List of Figures Chapters 1 to 3, Page Figure 1 Input connector of the CT2020HD ..........5 Reference Guide: CT2020HD Page v March 08...
- Page 6 About this Reference Guide This Reference Guide provides instructions and information for the installation and operation of the CT2020HD. This Reference Guide should be kept in a safe place for reference for the life of the equipment. It is not intended that this Reference Guide will be amended by the issue of individual pages.
- Page 7 France (TDF), Europe, and is a registered trademark of CCS (now Musicam USA Incorporated), USA. ® Ethernet is a registered trademark of Xerox Corporation. ® XILINX is a registered trademark of Xilinx Inc. Reference Guide: CT2020HD Page vii March 08...
-
Page 8: Emc Compliance
EMC Compliance This equipment is certified to the EMC requirements detailed in Annex B, Technical Specification. To maintain this certification, only use the leads supplied or if in doubt contact Customer Services. Reference Guide: CT2020HD Page viii March 08... - Page 9 If you need to return equipment for repair, please contact Tel: + 49 6124 7239-00 Fax: + 49 6124 7239-29 BMS-Europe GmbH & Co. KG Schwalbacher Straße 12 65321 Heidenrod – Kemel Germany Reference Guide: CT2020HD Page ix March 08...
-
Page 10: Introduction To The Ct2020Hd
Chapter 1: Introduction 1. Introduction to the CT2020HD 1.1 Preliminary Remarks The present manual is provided for users and operators of the CT2020HD Transmitter. It is intended to support the installation, operation, maintenance and daily use of the unit in general. -
Page 11: Description
TV production and news gathering. Video Inputs The CT2020HD accepts only HDSDI information at the input: Reference Guide: CT2020HD Page 2 March 08... -
Page 12: User Interface
The linear power amplifier amplifies the output signal of the Modulator t o an output of about 400 mW (+26 dBm). The output port of the Low-Power Amplifier is located on top of the CT2020HD. Reference Guide: CT2020HD Page 3 March 08... -
Page 13: Installing The Equipment
12VDC. Essential a valid video signal must be connected to the desired input before power on the CT2020HD. • When you connect the CT2020HD as described in the following sections, make sure that the "Caution" instructions given there are observed. -
Page 14: Connectors
The RF output signal of the Low-Power Amplifier is fed out at the N(f) connector on top of the unit. The CT2020HD provides a RF output of about 400 mW (+26dBm). Connecting Signal Sources The Video signal supplied by the camera has to be applied to the HDSDI BNC(f) connector of the transmitter. -
Page 15: Shut-Down
CT2020HD. Failure to comply with these requirements may cause fatal damage to the battery/power pack and/or CT2020HD. Battery Powered Operation of the CT2020HD Many types of batteries are available on the market and we tried to support the best ones. -
Page 16: Operating The Equipment
2305 MHz Current transmit frequency With its automatically COFDM setup the customer menu is very easy to handle. When Button 3 is pressed and held for approximately 2sec. the setup menu is accessible. Reference Guide: CT2020HD Page 7 March 08... -
Page 17: March
To save the changed frequency press button 3 after all digits of the frequency are set. You also leave the frequency setup with this final step. To exit this submenu, press button 3. Reference Guide: CT2020HD Page 8 March 08... -
Page 18: Software Version
3.5 Remote Frequency*(optional) In the sub menu ’Remote Frequency’ the frequency of the data receiver can be set. This setting is however, only valid for the CT2020HD Series, which have integrated data receivers. Edit mode is reached by pressing button 3 for 2 seconds. Here, with buttons 1 & 2, the various frequency channels can be chosen. -
Page 19: Latency
3.7 Modulation In the sub menu ’Modulation’ the Modulation method can be changed. The following options are possible: • QPSK • 16 QAM • 64 QAM ** setup: ** Modulation > 64-QAM < Reference Guide: CT2020HD Page 10 March 08... -
Page 20: Framerate
3.9 Resolution In the sub menu ’Resolution’ the desired resolution of your transmitter can be chosen There are three possible options available • • 720p • 1080i ** setup: ** Resolution > SD < Reference Guide: CT2020HD Page 11 March 08... - Page 21 Edit mode is reached by pressing button 3 for 2 seconds. With the arrow indicators 1 & 2 the desired Modulation can be chosen. To confirm press button 3. To exit this submenu, press button 3. Reference Guide: CT2020HD Page 12 March 08...
- Page 22 Quadrature phase shift keying (digital modulation technique) Phase Alternation Line (a color TV broadcasting system) Pulse Code Modulation Radio Frequency Red, green, blue. The chroma information in a video signal. RS 232, RS-232 EIA-232 Reference Guide: CT2020HD Page A-1 March 08...
- Page 23 Audio connector featuring three leads, two for signal and one for GND Y: Luminance component (brightness), U and V: chrominance (color difference) Broadcast Video with separate color, Y luminance and C chroma (sometimes called S-Video) Reference Guide: CT2020HD Page A-2 March 08...
-
Page 24: B.1.1 Safety
The version of the standards shown is that applicable at the time of manufacture. The EMC tests were performed with the Technical Earth attached, and configured using recommended cables. Applies only to models of the equipment using mains (ac) power sources. Reference Guide: CT2020HD Page B-1 March 08... -
Page 25: B.1.3 Shock And Vibration
73/23/EEC of 19 February 1973 on the harmonisation of the laws of the Member States relating to electrical equipment designed for use within certain voltage limits. B.1.5 FCC Marking FCC ID: VFB-CT2020HD-2000 for P/N 11.2422.500 VFB-CT2020HD-2300 for P/N 11.2422.100 Radio Frequency Interference (FCC 15.105) This equipment has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 of the FCC Rules. - Page 26 • This device must accept any interference received, including interference that may cause undesired operation. Modifications (FCC 15.21) Changes or modifications to this equipment not expressly approved by BMS may void the user’s authority to operate this equipment. Reference Guide: CT2020HD Page B-3 March 08...
-
Page 27: B.2 Technical Specifications
11 to 17.5 VDC Power Consumption Operating Conditions Ambient temperature -20°C to +45°C Dimensions (W x D x H) 272 mm x 106 mm x 56 mm (without Battery bracket) Weight 1.45 kg approx Reference Guide: CT2020HD Page B-4 March 08...