GME RCU9200 series Instruction Manual
GME RCU9200 series Instruction Manual

GME RCU9200 series Instruction Manual

Wired remote
Hide thumbs Also See for RCU9200 series:

Advertisement

Quick Links

RCU9200
W I R E D R E M OT E
I N S T R U C T I O N M A N U A L
G R 9 2 0 0 s e R i e s
i n s t R u c t i o n m a n u a l
Pa G e 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RCU9200 series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for GME RCU9200 series

  • Page 1 RCU9200 W I R E D R E M OT E I N S T R U C T I O N M A N U A L G R 9 2 0 0 s e R i e s i n s t R u c t i o n m a n u a l Pa G e 1...
  • Page 2 COnTEnTs contRols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 installation .
  • Page 3: Controls

    COnTROls 1 . Power 4 . Fast Foward/tune 7 . Rewind/tune 2 . lcD Window 5 . Volume up 8 . mode 3 . mute 6 . Volume Down G R 9 2 0 0 s e R i e s i n s t R u c t i o n m a n u a l Pa G e 3...
  • Page 4: Installation

    Do not remove the two bottom InsTAllATIOn. nuts as these are required to hold MOUnTIng. the bolts in place . slide the u-Bracket over the bolts the Rcu9200 is designed to be ensuring the clearance slots in the panel mounted . the mounting bracket are positioned as shown .
  • Page 5: Operation

    this to an accessory point in Rewind/ Tune your vessel will ensure the back in tuner mode, briefly press lighting turns on and off with your to manually tune downwards in vessels accessory switch . frequency . Press and HolD OPERATIOn to scan downwards in frequency .
  • Page 6: Mounting Diagram

    MOUnTIng DIAgRAM cut outs nuts u Bracket Pa G e 6 i n s t R u c t i o n m a n u a l R c u 9 2 0 0 s e R i e s...
  • Page 7: Installation Diagram

    InsTAllATIOn DIAgRAM Panel minimum Depth 60mm u-Bracket Front Facia Rubber Gasket + 12 V Dc to GR9200 switched G R 9 2 0 0 s e R i e s i n s t R u c t i o n m a n u a l Pa G e 7...
  • Page 8: Contract Warranty

    STaNDaRD cOMMUNicaTiONS cONTRacT WaRRaNTy 1. sTATUTORY repaired; or WARRAnTIEs (b) in the case of services we supply, to any one of the following as we decide - 1 . 1 the trade Practices act Part V, Division 2a and other (i) the supplying of the services again;...
  • Page 9 3. OThER lIMITATIOns 3 . 1 You may not rely on any representation, warranty or other provision by or for us which is not covered by clause [ 1 ] or repeated in this agreement in clear terms . 3 . 2 We are not liable (nor are our employees, contractors and agents) for any damage, economic loss or loss of profits whether direct, indirect, general, special or consequential -...
  • Page 10 (09) 274 0955 F: (07) 3278 6555 F: (02) 9816 4722 F: (09) 274 0959 For customers outside australia and new Zealand please contact your local Gme retailer or email: export@gme .net .au www.gme.net.au Part number: 310462 Drawing number: 44629-1...
  • Page 11 CUTTIng TEMPlATE outer edge of wired remote mounting hole (Push out) (Push out) 76mm 90mm G R 9 2 0 0 s e R i e s i n s t R u c t i o n m a n u a l Pa G e 1 1...
  • Page 12 cuttinG temPlate...

Table of Contents