Table of Contents
Advertisement
Quick Links
Sterimixer and Sanimixer
STD0016EN00
APPLIES TO:
Steridose products Sterimixer
®
Sterimixer
-ATEX, Sanimixer.
CONTENTS
1 Important safety information
1.1 Introduction . . . . . . . . . . . . . . . . . .
1.2 Safety terminology and symbols . . . . . .
1.3 General safety . . . . . . . . . . . . . . . . .
1.4 User safety . . . . . . . . . . . . . . . . . . .
2 Handling
3 Installation and start-up
3.1 Mounting of the bearing unit . . . . . . . .
3.2 Mounting the impeller . . . . . . . . . . . .
3.3
Use of the bearing / impeller installation
tool (Option). . . . . . . . . . . . . . . . . .
3.4 Mounting and dismounting the drive unit .
3.5 Connection to main power . . . . . . . . . .
3.6 Installation check and calibration . . . . . .
4 Operation
4.1 Allowed operating temperature range . . .
4.2 Allowed pressure range . . . . . . . . . . .
4.3 Chemical compatibility . . . . . . . . . . . .
4.4 Operational limits . . . . . . . . . . . . . . .
4.5 Further operational advice . . . . . . . . . .
4.6
Guidance
for
ixer/Sanimixer . . . . . . . . . . . . . . . .
4.7
Specific information for the use of Sterim-
ixer/Sanimixer in ATEX applications . . . .
5 Maintenance
5.1
Routine
maintenance
up/running in . . . . . . . . . . . . . . . . .
6 Troubleshooting
Copyright © 2017 Steridose
Generated by Steridocs: December 14, 2017
®
-Low-Shear SMO/SMA, Sterimixer
sterilizing
Sterim-
10
11
12
during
start
13
13
www.steridose.com
®
-Medium-Shear SMMS,
2
2
2
2
2
3
3
3
4
5
5
6
6
7
7
7
7
7
9
INSTALLATION
& OPERATION
MANUAL
Installation & Operation
| 1
Advertisement
Table of Contents
Summary of Contents for Steridose Sterimixer-Low-Shear SMO
- Page 1 5 Maintenance Routine maintenance during start up/running in ....6 Troubleshooting Copyright © 2017 Steridose Generated by Steridocs: December 14, 2017 www.steridose.com Installation & Operation...
-
Page 2: Important Safety Information
If, by undertaking any work covered by this document, you become aware of any Steridose product design related feature which could create risk to a person undertaking NOTICE: Indicates: A potential situation which, if not work or to the Sterimixer/Sanimixer and/or its compo- avoided, could result in undesirable conditions or con- nents please contact Steridose immediately. -
Page 3: Handling
(Table 2). Make sure that the PTFE washer is centered CAUTION: If the Sterimixer/Sanimixer is not to be in- correctly. Steridose have designed a tool for this purpose stalled immediately, the Sterimixer/Sanimixer should that facilitates mounting the bearing unit in hard-to-access be repacked in the original package and stored in a suit- places. -
Page 4: Mounting The Impeller
Carefully position the impeller onto the bearing unit and spin by hand to ensure that the impeller runs freely. Steridose have designed a tool for this purpose that facili- tates mounting the impeller in hard-to-access places. See section 3.3. -
Page 5: Use Of The Bearing / Impeller Installation Tool (Option)
PTFE washer. This prevents the PTFE washer from 1. Lift up the drive unit and let the flange screws loosening from the bearing unit during mounting. pass through the holes in the drive unit flange. www.steridose.com Installation & Operation | 5... -
Page 6: Connection To Main Power
(applies only to the external power supply. Steridose-supplied control boxes). The pre-set parameters include acceleration time (ramp-up), deceleration time An electrical drawing/wiring diagram is supplied with (ramp-down), maximum speed, and minimum speed. -
Page 7: Operation
All sizes -25 - +40 C Refer to table 6 or contact Steridose for further assis- (-13 - +104 F) tance. The permanent magnets in the impeller withstand temperatures up to +225 C (autoclave cleaning) 4.4. - Page 8 Best - lowest coefficient of running conditions friction Table 6 Comparison of bearing materials. The use of dissimilar materials in male and female bearings is not recommended Exact value depends on particular fluid properties, temperature and exposure time. 8 | © Steridose www.steridose.com...
-
Page 9: Further Operational Advice
2. Close the outlet and fill with cleaning agent having The operational parameters are pre-set in the control the fluid level above the impeller with at least 150 - box (applies only to Steridose-supplied control boxes). In 200 mm. extreme working conditions, uncoupling of the magnetic coupling can occur, i.e. -
Page 10: Guidance For Sterilizing Sterim Ixer/Sanimixer
To prevent this, a magnetic drive dismounting. The selection of method from those listed dummy can be installed to avoid any risk of damage below depends on the individual conditions. and hold the impeller in place. 10 | © Steridose www.steridose.com... -
Page 11: Specific Information For The Use Of Sterim Ixer/Sanimixer In Atex Applications
(Machinery Sweden Directive) and with regards to explosion protection (ATEX Directive 94/9/EC). Only then can a CE mark be granted. Steridose AB (a Velcora company) Himmelsbodavägen 7 4.7.2. Magnetic mixers in Ex zones SE 147 39 Tumba... -
Page 12: Maintenance
Life time of the Sterim- ating a possible hazard. Each and every application ixer/Sanimixer depends on the application, so shorter shall be assessed individually to ensure the safety service intervals may apply. conditions are maintained. 12 | © Steridose www.steridose.com... -
Page 13: Routine Maintenance During Start Up/Running In
This refurbishment can only be done at the Steridose factory or authorized Steridose service center. Male bearing units cannot refurbished, they must be re- placed when worn. - Page 14 Reduce speed and the formation c) Due to high speed of vortices d) Magnetic particles d) Magnetic particles are not re- moved during normal cleaning. The impeller must be removed and cleaned separately Table 7 Troubleshooting. 14 | © Steridose www.steridose.com...
-
Page 15: Www.steridose.com Installation & Operation
Installation & Operation | 15... - Page 16 5020 World Dairy Drive Madison, WI 53718, U.S.A. Phone: +1 608 229 5225 info@steridose.com www.steridose.com Visit our website for the latest version of this document. The original instruction is in English, all non-English instructions are translations of the original instruction. © Steridose AB...
Need help?
Do you have a question about the Sterimixer-Low-Shear SMO and is the answer not in the manual?
Questions and answers