Subscribe to Our Youtube Channel
Related Manuals for DuroStar DS5018CS
Summary of Contents for DuroStar DS5018CS
- Page 1 CHAIN SAW OWNER'S MANUAL MODEL:DS5018CS Caution: Before using our chain saw, please read this manual carefully to understand the proper use of your unit Keep this manual available for reference at all times.
- Page 2 OWNER’S MANUAL △ SAFETY FIRST Instructions contained in warnings within this manual marked with a △ symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury and for this reason you are requested to read all such instructions carefully and follow them without fail.
-
Page 3: Warning Labels On The Machine
OWNER’S MANUAL 1.WARNING LABELS ON THE MACHINE a. Read owner's manual before operating this machine b. Wear head, eye, and ear protection c. Use the chain saw with two hands d. Warning! Kickback danger e. Warning/Attention △ WARNING ！ Never remodel the product. We won’t warrant the machine if you use the remodeled product or you don’t observe the proper usage written in the manual. -
Page 4: Symbols On The Machine
OWNER’S MANUAL 2. SYMBOLS ON THE MACHINE For safe operation and maintenance, symbols are carved in relief on the machine. Per these indications, please be careful not to make a mistake. a. The port to refill the “MIXED GASOLINE” b. The port to refill the “CHAIN OIL” c. -
Page 5: Safety Precautions
OWNER’S MANUAL 3.SAFETY PRECAUTIONS BEFORE USING THE MACHINE a. Read this owners manual carefully to understand how to operate this unit properly. b. You should never use the product when under the influence of alcohol, when suffering from exhaustion or lack of sleep, when suffering from drowsiness because of having taken cold medicine, or at any other time when a possibility exists that your judgment might be impaired or that you might not be able to operate the machine properly and in a safe manner. - Page 6 OWNER’S MANUAL WARNING CONSIDERING HANDLING OF FUEL a. The engine of this product is designed to run on a mixed fuel which contains highly flammable gasoline. Never store cans of fuel or refill the fuel tank in any place where here is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel.
- Page 7 OWNER’S MANUAL OPERATION a. Keep the handles dry, clean, and free of oil or fuel mixture. b. Never touch the muffler, spark plug, or other metal parts of the engine while the engine is in operation or immediately after stopping the engine. Doing so could result in serious burns or electrical shock.
-
Page 8: Installing Guide Bar And Saw Chain
OWNER’S MANUAL 4.INSTALLING GUIDE BAR AND SAW CHAIN A standard saw unit package contains the items as illustrated (1) power unit (2) Bar protector (3) Guide bar (4) Saw chain (5) Plug wrench (6) Hexagon wrench Open the box and install the guide bar and the saw chain on the power unit as follows: a. -
Page 9: Fuel And Chain Oil
OWNER’S MANUAL 5.FUEL AND CHAIN OIL FUEL △ WARNING ！ Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m away from the fueling point before starting the engine. - Page 10 OWNER’S MANUAL piston seizing due to abnormally lean mixture. FUELING THE UNIT a. Untwist and remove the fuel cap. Rest the cap on a dustless place. b. Put fuel into the fuel tank to 80％ of the full capacity. c. Fasten the fuel cap securely and wipe up any fuel spillage around the unit.
-
Page 11: Operating Engine
OWNER’S MANUAL 6.OPERATING ENGINE STARTING ENGINE a. Fill fuel and chain oil tanks respectively, and tighten the caps securely. b. Put the switch to “ON” position. c. Pull out the choke knob to the second-stage position. The choke will close and the throttle lever will then be set in the starting position. - Page 12 OWNER’S MANUAL (1) Chain oil ADJUSTING CARBURETOR The carburetor on your unit has been adjusted by the factory, but may require fine turning due to change in operating conditions. Before adjusting the carburetor, make sure that provided are clean air/fuel filters and fresh, properly mixed fuel.
-
Page 13: Sawing
OWNER’S MANUAL (1) Switch 7.SAWING △ WARNING ！ It is not necessary to force the saw into the cut. Apply only light pressure while running the engine at full throttle. When the saw chain is caught in the cut, do not attempt to pull it out by force, but use a wedge or a lever to open the way. - Page 14 OWNER’S MANUAL (3) Felling direction Bucking and Limbing △ WARNING ！ Always ensure your foothold. Do not stand on the log. Be alert to the rolling over of a cut log. Especially when working on a slope, stand on the uphill side of the log. ...
-
Page 15: Maintenance
OWNER’S MANUAL 8.MAINTENANCE △ WARNING ！ Before cleaning, inspecting or repairing your unit, make sure that engine has stopped and is cool. Disconnect the spark plug to prevent accidental starting. MAINTENANCE AFTER EACH USE a. Air Filter To clean dirt in the meshes, split the cleaner into halves and brush in gasoline. - Page 16 OWNER’S MANUAL SERVICE POINTS a. Cylinder fins Dust clogging between the cylinder fins will cause over heating of the engine. Periodically check and clean the cylinder fins after removing the air cleaner and the cylinder cover. NOTE Be sure to block the air intake hole. b.
- Page 17 OWNER’S MANUAL worn sprocket, or a worn chain on a new sprocket. 9. MAINTENCE OF SAW CHAIN AND GUIDE BAR △ WARNING ！ It is very important for smooth and safe operation to keep the cutters always sharp. a. Your cutters need to be sharpened when: ...
-
Page 18: Troubleshooting Guide
OWNER’S MANUAL Reverse the bar occasionally to prevent partial wear. 10.TROUBLESHOOTING GUIDE Case 1. Starting failure △ Make sure the icing prevention system is not active！ Check fuel for water or Replace with proper fuel. substandard mixture. Check for engine Remove and dry the spark plug. -
Page 19: Specifications
OWNER’S MANUAL 11. SPECIFICATIONS: Model DS5018CS Displacement (cc) 52cc Max. Output (kW/r/min） 2.0/8500 Fuel Mix 40:1 Fuel tank capacity (oz.) 17.9 Chain oil Bar and Chain Oil Oil tank capacity (oz.) 8.45 Carburetor Diaphragm Type Ignition system C.D.I Spark plug... - Page 20 DuroStar Power Equipment 5798 Ontario Mills Pkwy Ontario CA 91764 800-629-3325 M – F 7:00a – 5:00p PT support@maxtool.com...
Need help?
Do you have a question about the DS5018CS and is the answer not in the manual?
Questions and answers