Related Manuals for SUNRICH TECHNOLOGY N-480
Summary of Contents for SUNRICH TECHNOLOGY N-480
-
Page 1: User Manual
PCIe 10G 5-Speed Multi-Gigabit Network Card User Manual Ver. 2.00 All brand names and trademarks are properties of their respective owners. - Page 2 Contents: Chapter 1: Introduction ............3 1.1 Product Introduction ............ 3 1.2 Features ................ 4 1.3 Requirements ............... 4 1.4 Package Contents ............5 Chapter 2: Getting Started ..........6 2.1 Hardware Layout ............6 2.2 Hardware Installation ..........7 2.3 Driver Installation ............
-
Page 3: Chapter 1: Introduction
Chapter 1: Introduction 1.1 Product Introduction This card is a Multi-Gigabit network adapter that’s runs on a high speed PCIe x4 host bus interface. This card hosts the Tehuti’s new 3 generation TN4010 controller, and optimized 10 Gigabit Ethernet MAC designed for low-power, low-cost, single-port connectivity required by Application Servers and Workstations. -
Page 4: Features
1.2 Features Support 5-Speed 10Gb/5Gb/2.5Gb/1Gb/100Mb auto negotiation Runs up to 10G at 100m Cat 6A cable and 5G at 100m Cat 5e/Cat 6 cable Backward compatibility with 1000Base-T, 100Base-T Networks PCI Express Gen-2 x4 host bus interface ... -
Page 5: Package Contents
Software Operating systems supported are (both 32 and 64 bits) Windows 7 Windows 8.1 Windows 10 Windows Server 2008 R2 Windows Server 2012 Windows Server 2012 R2 Linux 2.6.32 or later VMware ESXi 5.x/6.0 ... -
Page 6: Chapter 2: Getting Started
Chapter 2: Getting Started 2.1 Hardware Layout Link/Activity Indicator: When the LED is off, there is no link between the PCIe 10G 5-Speed Multi-Gigabit Network Card and the network When the LED is on, a link is established, but there is no traffic on the network ... -
Page 7: Hardware Installation
Link Speed Indicator: When the LED is lit orange, a 10GBase-T link is established When the LED is lit green, a 5GBase-T/2.5GBase-T/1000Base-T link is established When the LED is off, a 100Base-T link is established 2.2 Hardware Installation Turn off the power to your computer. -
Page 8: Installation For Windows
2.3.1 Installation for Windows Insert the provided CD into your disk drive. The CD-ROM will start automatically. The following screen will show up and please click “Install Driver”. *Note: Actual image may vary Note: If the install program doesn’t run automatically, please locate and double-click on the Autorun.exe file in the CD to launch the install program. -
Page 9: Installation For Linux
*Note: Actual image may vary Follow the instructions on screen to install the driver. 2.3.2 Installation for Linux Insert the provided CD into your CD-ROM drive. Extract the compressed driver source file to a certain directory by the following command: (Please copy the driver file “tn40xx-x.x.x.x.tgz”... -
Page 10: Verifying The Installation
# make If the compilation is well, the tn40xx.ko will be created under the current directory. If you want to use modprobe command to mount the driver, executing the following command to install the driver into your kernel: # make install 2.4 Verifying the installation 2.4.1 Verifying for Windows Click on the “Device Manager”... -
Page 11: Verifying For Linux
Entry “Network adapters” item, and you can read “Tehuti Networks 10GbE Adapter” in the Device Manager. 2.4.2 Verifying for Linux You can check whether the driver is loading by using following commands: # lsmod | grep tn40xx # ifconfig –a If there is a device name, ethX, shown on the monitor, the linux driver is load.
Need help?
Do you have a question about the N-480 and is the answer not in the manual?
Questions and answers