AOC e2250Sda Service Manual

AOC e2250Sda Service Manual

21.5" lcd monitor
Hide thumbs Also See for e2250Sda:

Advertisement

Quick Links

21.5" LCD Monitor
Service
Service
Service
Description
Table of Contents....................................................1
Revision List...................................................................2
Important Safety Notice.................................................3
1.Monitor Specification...................................................4
2.LCD Monitor Description.........................................5
3.Operation Instruction.................................................6
3.1.General Instructions..................................................6
3.2.Control Buttons and Connections...............................6
3.3.OSD Setting.............................................................8
4.Input/Output Specification........................................24
4.1.Input Signal Connector..........................................24
4.2.Preset Display Modes................................25
4.3.Panel Specification...........................................26
5.Block Diagram............................................................28
5.1.Main Board.....................................................28
5.2.Power Board..................................................29
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
Table of Contents
Page Description
6.Schematic..........................................................30
6.1.Main Board.......................................................30
6.2.Power Board....................................................35
7.PCB Layout.........................................................37
7.1.Main Board......................................................37
7.2.Power Board.....................................................39
7.3.Key Board........................................................41
8.Maintainability.....................................................42
8.1.Equipments and Tools Requirement..................42
8.2.Trouble Shooting.............................................43
9.White-Balance,Luminance Adjustment.................47
10.Mechanical Instructions ............... ..............49
11.Monitor Exploded View......................................57
12.BOM List......................................................58
SAFETY NOTICE
1
AOC e2250Sda
Horizontal Frequency
30 - 83kHz
Page

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the e2250Sda and is the answer not in the manual?

Questions and answers

Summary of Contents for AOC e2250Sda

  • Page 1 21.5" LCD Monitor AOC e2250Sda Service Service Service Horizontal Frequency 30 - 83kHz Table of Contents Description Page Description Page Table of Contents…………………..…………………..…...1 6.Schematic…………..….........30 Revision List.…...........……..2 6.1.Main Board..…….…...........30 Important Safety Notice.….…......……..3 6.2.Power Board..……….........35 1.Monitor Specification......………....4 7.PCB Layout..………..........37 2.LCD Monitor Description……….……………………..5 7.1.Main Board………..…........37...
  • Page 2: Revision List

    Revision List Version Release Date Revision History TPV Model Name Initial release TCBMN26BAGA1DNE Aug.-12-2011...
  • Page 3: Important Safety Notice

    Important Safety Notice Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The service procedures recommended by AOC and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. The special tools should be used when and as recommended.
  • Page 4: Monitor Specification

    1.Monitor Specifications...
  • Page 5: Lcd Monitor Description

    2.LCD Monitor Description The LCD monitor will contain a main board, an adapter board, a converter board and a key board which house the flat panel control logic, brightness control logic and DDC. The power part will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage.
  • Page 6: Operating Instructions

    3. Operating Instructions 3.1 General Instructions Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the monitor (See Figure ). By changing these settings, the picture can be adjusted to your personal preferences. * The power cord should be connected.
  • Page 7 1.Power 2. Analog (DB-15 VGA cable) 3. DVI 4. Audio To protect equipment, always turn off the PC and LCD monitor before connecting. 1 Connect the power cable to the AC port on the back of the monitor. 2 Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port.
  • Page 8: Osd Setting

    3.3 OSD Setting Basic and simple instruction on the control keys. 1) Press the MENU-button to activate the OSD window. 2) Press - or + to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. press - or + to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it.
  • Page 9 Luminance Press (Menu) to display menu. Press to select (Luminance), and press to enter. Press to select submenu, and press to enter. Press to adjust.
  • Page 10 Press two times to exit.
  • Page 11 Image Setup Press (Menu) to display menu. Press to select (Image Setup), and press to enter. Press to select submenu, and press to enter. Press to adjust.
  • Page 12 Press two times to exit.
  • Page 13 Color Setup Press (Menu) to display menu. Press to select (Color Setup), and press to enter. Press to select submenu, and press to enter. Press to adjust.
  • Page 14 Press two times to exit.
  • Page 15: Picture Boost

    Picture Boost Press (Menu) to display menu. Press to select (Picture Boost), and press to enter. Press to select submenu, and press to enter. Press to adjust.
  • Page 16 Press two times to exit.
  • Page 17 OSD Setup Press (Menu) to display menu. Press to select (OSD Setup), and press to enter. Press to select submenu, and press to enter. Press to adjust.
  • Page 18 Press two times to exit.
  • Page 19 Extra Press (Menu) to display menu. Press to select (Extra), and press to enter. Press to select submenu, and press to enter. Press to adjust.
  • Page 20 Press two times to exit.
  • Page 21 Exit Press (Menu) to display menu. Press to select (Exit), and press to enter. Press two times to exit...
  • Page 22: Led Indicators

    Orange or red e-Saver Welcome to use AOC e-Saver monitor power management software! The AOC e-Saver features Smart Shutdown functions for your monitors, allows your monitor to timely shutdown when PC unit is at any status (On, Off, Sleep or Screen Saver);...
  • Page 23 Screen+ Welcome to "Screen+" software by AOC, Screen+ software is a desktop screen splitting tool, it splits the desktop into different panes, each pane displays a different window. You only need to drag the window to a corresponding pane, when you want to access it.
  • Page 24: Input/Output Specification

    4. Input/Output Specification 4.1 Input Signal Connector...
  • Page 25: Preset Display Modes

    4.2 Preset Display Modes...
  • Page 26: Panel Specification

    4.3 Panel Specification 4.3.1 General Features The M220Z3-LA3 model is a 22 inch wide TFT-LCD slimming module with a WLED light bar Backlight Unit and a 30-pin 2ch-LVDS interface. This module supports 1680 x 1050 WSXGA (16:10 wide screen) mode and displays up to 16.7 millions colors.
  • Page 27 Backlight unit Ta = 25 ±2 ℃ , I= 25 mA, Duty=100%, IPIN=25mA 4.3.4 Optical Characteristics 25°C...
  • Page 28: Block Diagram

    5. Block Diagram 5.1 Main Board 04.SCALER 02.INPUT VCC3.3 VCC3.3 SOG_DET VCC1.8 SOG_DET SOG_DET VCC1.8 05.PANEL INTERFACE EDID_WP AHS0 EDID_WP AHS0 AHS0 AVS0 AVS0 AVS0 PA[0..9] DDCSDA1 DDCSDA1 DDCSDA1 PA[0..9] PA[0..9] DDCSCL1 DDCSCL1 DDCSCL1 VGA_CABLE_DET VGA_CABLE_DET VGA_CABLE_DET PB[0..9] 02.D-SUB INPUT PB[0..9] PB[0..9] EDID_WP...
  • Page 29: Power Board

    5.2 Power Board AC input Transformer Rectifier Bridge 14.5V EMI filter (T901) diodes Rectifier and Filter Start Resistor (R908,R911) Feedback PWM Control Circuit Power Switch LD7576AGR (Q901) (U901) Photo coupler Regulator (U902) (IC903) L801 ZD801 MOSFET (Q801) (CN805) PWM Control TA9690GN (IC801)
  • Page 30: Main Board

    6. Schematic 6.1 Main Board 715G4502M01000004C CN101 DET_VGA R102 100R 1/16W 5% VGA_CABLE_DET VGA_CABLE_DET 5 D-SUB 15P VGA_5V DDCSCL1 R101 DDCSCL_A DDCSCL1 VGA_5V 100R 1/16W 5% VSIN0 BIN0- HSIN0 BIN0 R103 R104 R105 C102 GIN0- ZD101 BIN0 0R05 1/16W 0R05 1/16W 100R 1/16W 5% 47N16V B0+ 5...
  • Page 31 CN102 R127 DVI_CABLE_DET 5 JACK 100R 1/16W 5% DVI5V 3,5,7 VSY NC DET_DVI DVI5V SY NC GND SCL_DVI R128 100R 1/16W 5% D102 DDC SCL SDA_DVI R129 100R 1/16W 5% ESD_DVI BAV70 DDC SDA DVI5V R130 1K 1/16W 5% U104 Q101 ESD_DVI ESD_DVI...
  • Page 32 VCC1.8 U401 NT68660FG FB401 and FB402 is VCC1.8 7 PB[0..9] R402 NC/2K2 1/16W 5% PB[0..9] NC==>3.3V use TO252 type LVB3P FB401 R403 NC/2K2 1/16W 5% CVDD LVB3M 300OHM U401 NT68660UFG FB402 is NC==>3.3V LVBCKP LVBCKM VCC3.3 and 1.8V LDO use SOT-223 type LVB2P C401 C402...
  • Page 33 PA[0..9] PB[0..9] PA[0..9] PB[0..9] LVB3P CN408 LVA3P LVB3M CONN LVA3M LVBCKP LVB0M RXO0- LVACKP LVBCKM LVB0P RXO0+ LVACKM LVB2P LVB1M RXO1- LVA2P LVB2M LVB1P RXO1+ LVA2M LVB1P LVB2M RXO2- LVA1P LVB1M LVB2P RXO2+ LVA1M LVB0P LVA0P LVB0M LVBCKM RXOC- LVA0M LVBCKP RXOC+ LVB3M...
  • Page 34 VCC3.3 CN702 U701 AZ1117H-3.3TRG1 FB701 0 OHM +-5% 1/8W 3,4,5 INPUT OUTPUT VCC3.3 5 VCC3.3 ADJ/GND ON/OFF NC/CONN C701 R702 4K7 1/16W 5% 100N 16V +5V 3,4,5 CN701 R703 100R 1/16W 5% Adj_BACKLIGHT 5 C706 U702 VCC3.3 100N 16V C705 NC/G1117-33T43UF 100uF16V ON/OFF...
  • Page 35: Power Board

    6.2 Power Board Adapter 715G4744P01000001C R929 100 OHM 1/4W BD901 C916 C928 F801 KBP208G R930 100 OHM 1/4W 2N2 500V 2N2 500V 0R05 1/4W +14.5V R903 100 OHM 1/4W R904 ZD901 250OHM2W MTZJ T-72 16B 80GL22T-3 C918 NC/680UF/25V T901 D901 POWER X'FMR SR515 R905...
  • Page 36 Converter 715G3918P03000004C R844 NC C811 NC Vout CN801 CONN ZD801 +12V F801 FUSE L801 B3100B R833 1 OHM 1/10W R832 1 OHM 1/10W CN803 R831 1 OHM 1/10W 22uH R830 1 OHM 1/10W C801 C813 C803 C804 C810 100uF 50V 100N 50V 220P 100V 33UF 100V...
  • Page 37: Pcb Layout

    7. PCB Layout 7.1 Main Board 715G4502M01000004C...
  • Page 39: Power Board

    7.2 Power Board Adapter 715G4744P01000001C...
  • Page 40 Converter...
  • Page 41: Key Board

    7.3 Key Board 715G4747K02000001C...
  • Page 42: Maintainability

    8. Maintainability 8.1 Equipments and Tools Requirement Voltmeter. Oscilloscope. Pattern Generator. DDC Tool with an IBM Compatible Computer. Alignment Tool. LCD Color Analyzer. Service Manual. User Manual.
  • Page 43: Trouble Shooting

    8.2 Trouble Shooting 1. No Power No power Check power cable is Re-plug the power cable tightened? Check Power “On/Off” Turn on the Power “On/Off” switch is “On”? Check the LED Check the AC power indicate is OK? Replace the converter board Replace main board and check connections Replace key board and check connections...
  • Page 44 2. No Video (Power LED Blue) No Video (Power LED Blue) Press the power Replace the main board button is OK? Replace the converter The end board Replace the main The end board and connection Replace the LVDS/FFC Check the LVDS/FFC cable or panel cable or panel Replace the key board...
  • Page 45 3. DIM DIM (image overlap, focus or flicker) Reset in factory mode The end Set to the optimal The end frequency, select the recommended frequency Readjust the phase and pixel The end clock in the user mode Pull out signal cable and Check the signal cable check “Self Test Feature and the PC...
  • Page 46 4. Color is not optimal Color is not optimal Color shift Miss color Reset the factory mode Replace the signal cable In the user mode, set the” color settings” until customer satisfy The end Pull out the signal cable and check the screen color display is normal? Replace the signal cable or PC Replace the main board...
  • Page 47: White-Balance,Luminance Adjustment

    9.White- Balance, Luminance Adjustment Approximately 30 minutes should be allowed for warm up before proceeding white balance adjustment. How to setting MEM channel you can reference to chroma 7120 user guide or simple use “SC” key and “NEXT” Key to modify xyY value and use “ID” key to modify the TEXT description Following is the procedure to do white-balance adjust .
  • Page 48 C. Adjust Cool (9300K) color-temperature 1. Switch the Chroma-7120 to RGB-Mode (with press “MODE” button) 2. Switch the MEM. Channel to Channel 9 (with up or down arrow on chroma 7120) 3. The LCD-indicator on chroma 7120 will show x=283±20,y=297±20 4.
  • Page 49: Mechanical Instructions

    10.Mechanical Instructions 1. Put the monitor on the EPE pad. 2. Lay down the monitor and the bottom side faces to Yourself.
  • Page 50 3. Pinch the hook and remove the base. 4. Use fixture to leave off the stand.
  • Page 51 5. Use fixture to remove the hinge cover. 6. Remove the screws of the stand.
  • Page 52 7. Remove the screws of the back cover. 8. Overturn the monitor and the top towards to yourself, and then take apart the front frame with hands.
  • Page 53 9. Prize up the front frame use fixture. 10. Overturn the monitor and take off the back cover.
  • Page 54 11. According to the different defective area to take off the KEPC, light line, LVDS, Hexagon screws, CBPC or PWPC to repair. (1)Remove the KEPC. (2)Pull the light line out.
  • Page 55 (3)Remove the Hexagon screws. (4)Remove the LVDS.
  • Page 56 (5)Overturn the iron plate and remove the screws, PWPC and CBPC.
  • Page 57: Monitor Exploded View

    11. Monitor Exploded Views PART NAME Q'TY BEZEL FUNCTION BUTTON POWER LENS MYLAR MAIN FRAME HINGE PLATE REAR COVER HINGE STAND STAND COVER BASE RUBBER FOOT HINGE COVER...
  • Page 58: Bom List

    EU address card H44GC013101 EPE-2 22W H44GC013201 EPE-2 22W H44GC013615 2A e2250Sda CARTON H45G 87 1 25 EPE COVER H52G1801 16006 insulating sheet H70G22C1615 1B e2250Sda CD MANUAL KEPCAHB5 KEY BOARD Q34G7386ABJA3B0130 BEZEL Q34G7387ABJ 2B0100 REAR COVER 22W Q40G 58162435A LABEL...
  • Page 59 Q45G 76 28 H PE BAG FOR MANUAL Q52G 1185 99 TAPE Q52G6019 14 TAPE E09504 S95G176T12W01 FFC CABLE 224MM 12P 0.5MM 2nd source E08907 S95G179T30NE40 FFC CABLE 30pin 217mm 1.0mm 2nd source 756GHBCB A1032 MAIN BOARD-CBPCBN2A2H2 SMTCB-U402 100GANMC001W11 MCU ASS'Y-056G2233 11 GND1 009G6005 1 GROUND TERMINAL...
  • Page 60 090G6084 1 HEAT SINK D906 093G 60507 SCHOTTKY SRF1060 C0 10A 60V ITO-220AB 0M1G 930 8120 SCREW 3x8 055G 23524 WELDING FLUX WITHOUT PB Q51G 6 4509 GLUE_RTV Q55G 100625 TIN STICK_LOW ARGENTUM U901 056G 379529 AC/DC CONVERTER IC LD7576AGR SOP-7 Q607 057G 417517 Tra LMBT3906LT1G -200mA/-40V SOT-23 LRC...
  • Page 61 C614 065G060310412K CAP CHIP 0603 100N 16V X7R +/-10% C608 065G060310512K CAP 0603 1UF 10% 16V X7R C609 065G060310512K CAP 0603 1UF 10% 16V X7R C617 065G060320131J CAP CHIP 0603 200PF J 50V NPO C618 065G060320131J CAP CHIP 0603 200PF J 50V NPO C619 065G060320131J CAP CHIP 0603 200PF J 50V NPO...
  • Page 62 Q402 057G 417517 Tra LMBT3906LT1G -200mA/-40V SOT-23 LRC Q701 057G 417518 TRA LMBT3904LT1G 200mA/40V SOT-23 LRC Q706 057G 417518 TRA LMBT3904LT1G 200mA/40V SOT-23 LRC Q705 057G 763940 MOSFET AO3401A SOT-23 R711 061G0402000 JT RST CHIPR MAX0R05 1/16W TZAI YUAN R453 061G0402000 JT RST CHIPR MAX0R05 1/16W TZAI YUAN R410...
  • Page 63 R415 061G0402104 JT RST CHIP 100K 1/16W 5% TZAI YUAN R422 061G0402104 JT RST CHIP 100K 1/16W 5% TZAI YUAN R715 061G0402104 JT RST CHIP 100K 1/16W 5% TZAI YUAN R432 061G0402105 JT RST CHIP R 1Mohm 1/16W +/-5% TZAI YUAN R413 061G0402222 JT RST CHIP 2K2 1/16W 5% TZAI YUAN...
  • Page 64 C117 065G040210412K CAP 0402 100NF 10% 16V X7R C118 065G040210412K CAP 0402 100NF 10% 16V X7R C119 065G040210412K CAP 0402 100NF 10% 16V X7R C402 065G040210412K CAP 0402 100NF 10% 16V X7R C403 065G040210412K CAP 0402 100NF 10% 16V X7R C405 065G040210412K CAP 0402 100NF 10% 16V X7R...
  • Page 65 Q904 057G 530503 T 2SD1207T R915 061G 17222052T TZ RST CFR 22R 5% 1/4W R906 061G152M10452T SY RST MOFR 100KOHM +-5% 2WS FUTABA R904 061G152M25152T SY RST MOF 250R 5% 2W R924 061G152M47852T SY RST MOFR 0.47 OHM +-5% 2WS FUTABA C911 065G 2K152 2T6921 CAP CER 1500pF K 2KV Y5P...
  • Page 66 R813 061G0603103 JT RST CHIP 10K 1/10W 5% TZAI YUAN R809 061G0603104 JT RST CHIP 100K 1/10W 5% TZAI YUAN R832 061G0603109 JT RST CHIP 1R 1/10W 5% TZAI YUAN R830 061G0603109 JT RST CHIP 1R 1/10W 5% TZAI YUAN R833 061G0603109 JT RST CHIP 1R 1/10W 5% TZAI YUAN...

Table of Contents