Quick Start Guide - NorthStar NSB12-310 Applications Manual

NorthStar UPS Quick Start Guide
Unpacking the Batteries
When received, the batteries should be inspected.
Make sure the batteries were not damaged during
transport, and that all the proper accessories were
included in the delivery. If problems arise, please
initiate a claim immediately.
Note: * indicates where further information can be
found in the NSB UPS Application Manual. Warnings
and notifications can be found on the label (shown
below) which appears on each product. Be aware and
adhere to all warnings which appear on the product.
NON-SPILLABLE / NON-SERVICEABLE
Contains: Lead, Sulfuric Acid (Electrolyte), Lead Compounds, Arsenic
Ensure reference materials are reviewed and made available to all operators
including application manual, installation guide, and MSDS.
DANGER
Harmful if swallowed, inhaled, or in contact with skin.
Acid causes severe skin burns and eye damage.
May damage fertility or the unborn child if ingested or inhaled.
May cause harm to breast-fed children.
May cause cancer if ingested or inhaled.
Causes skin irritation, serious eye damage.
Contact with internal components may cause irritation or severe burns.
Causes damage to central nervous system, blood and kidneys through prolonged
or repeated exposure if ingested or inhaled.
Irritating to eyes, respiratory system, and skin.
May form explosive air/gas mixture during charging.
Obtain special instructions before use.
Do not handle until all safety precautions have been read and understood.
Wash thoroughly after handling.
Do not eat drink or smoke when using this product.
Avoid contact during pregnancy/while nursing.
PROPOSITION 65 WARNING: Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Batteries also contain other
chemicals known to the State of California to cause cancer. Wash hands after handling.
WARNING: ºC or incinerate. Not recommended for inverted use. Follow product charging instructions.
Manufactured by:
NorthStar Battery Company
417 575 8000
MADE IN USA
Installation
1. Before proceeding with the installation of the
battery, review or determine the arrangement of the
batteries for the application.
2. Checking the voltage spread is vital before
connecting the monoblocks in series. Refer to section
10.2 for more information.
3. If installing multiple parallel strings, the cabling to
each string should be the same size and approximate
length resulting in the same resistance per string.
*(Battery Connection to Load/Charger 10.12)
4. The cable size selected should consider allowable
voltage drop of ≤ 0.5V
*(Battery Connection to Load/Charger 10.12)
5. Carefully install batteries into position as
determined. The battery should be oriented so that
Form: SES-541-01711
Wear protective gloves/protective clothing, eye protection/face protection.
Use only outdoors or in a well-ventilated area.
Avoid contact with internal acid.
Do not breathe dust/fume/gas/mist/vapors/spray.
IF SWALLOWED OR CONSUMED: rinse mouth. Do NOT induce vomiting. Call a
poison center/doctor if you feel unwell.
clothing and wash it before reuse. Rinse skin with water/shower.
IF INHALED: Remove person to fresh air and keep comfortable for breathing.
Immediately call a POISON CENTER or doctor/physician.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses,
if present and easy to do. Continue rinsing.
If exposed/concerned, or if you feel unwell seek medical attention/advice.
Store locked up, in a well-ventilated area, in accordance with local and
national regulation.
Dispose of contents/container in accordance with local and national regulation
Keep out of reach of children.
15
ISO
Pb
Pb
9001
BA TTERY MU ST
14001
BE R ECYCLED
the negative (-) post of one battery is adjacent to the
positive (+) post of the next adjacent battery.
6. Make sure the batteries are all evenly spaced
approximately 10mm (3/8 inch) apart.
7. Check that all contact surfaces are clean, and then
install the bloc or cell connectors and the terminal
screws using the torque value printed on the battery
label. *(Commissioning/Installation 10.9)
8. The insulation covers should be put back after all
connections have been completed.
*( Commissioning/Installation 10.10)
Charging
8. It is highly recommended to give the batteries a
refreshing charge prior to commissioning. A refreshing
charge shall be performed with at least 2.35 V/cell at
25°C (77°F) for at least 24 hours. Failure to observe
these conditions may result in greatly reduced capacity
and service life. *(Charge 10.14)
9. The optimum level for float charging the NSB UPS
batteries is 2.27 volts/cell at 25°C (77°F). *(Charge 2.2)
a.
b.
10. If the ambient temperature increases above
25°C (77°F), a thermal compensation of -2 mV/cell/°C
is recommended. Conversely, if the temperature
decreases below 25°C (77°F), the voltage should be
increased by 2 mV/cell/°C. *(Charge 2.2)
11. Verify the battery string voltage matches the
rectifier output voltage. *(Maintenance 11.3)
12. If a voltage difference is identified due to a voltage
drop in the cables, then the rectifier must be adjusted
until the battery string voltage is within battery
specification.
www.northstarbattery.com
Issued: 12-08-16
Example: 40 battery string = 544.8V
Example: 32 battery string = 435.8V
ECO-101191