Page 1
For FSC certified products look for the FSC label SGS-COC-005310 1996 Forest Stewardship Council A.C. Jungle Fun Swing Set :320...
Page 2
Fit N’ Fun Thank you for purchasing a Creative Cedar Designs Playcenter. We hope it will bring you and your children many years of safe and enjoyable backyard fun. Table of Contents Letter to Customer Positioning Your Playcenter Tools Required for Assembly Helpful Installation Hints Suggested Playground Surfacing Operating Instructions...
Page 3
STOP…PLEASE READ!! IF YOU HAVE ANY QUESTION OR ARE MISSING A PART, PLEASE DO NOT CONTACT THE RETAILER THAT YOU PURCHASED THIS PRODUCT FROM. PLEASE VISIT www.creativecedardesigns.com OR CONTACT US DIRECTLY AT OUR OFFICE, 1-888-363-4967 WE WILL ANSWER YOUR QUESTIONS, OR HELP WITH WHAT YOU NEED. For more efficient service, please log onto our website at www.creativecedardesigns.com...
Page 4
Date of Purchase:_______________ Date stamped on box:______________ Manufacturer: Creative Cedar Designs Vendor: _____ _________________ ______________________ 2700 Riverside Dr. ______________________ Chattanooga, TN 37406 E-mail: custservice@creativecedardesigns.com Website: www.creativecedardesigns.com Unit Type: Unit Name: Jungle Fun Swing Set Revision Date: 10/04/2016 Unit Model Number: MA3201 Maximum Fall Height: 7-7"...
The instructions and owner’s manual for your new Playcenter should be read in its entirety before assembly, to minimize problems and safety issues. We recommend reading the owner’s manual thoroughly after you have identified all of the parts for your Playcenter as discussed in the Helpful Installations Hints section below.
Helpful Installation Hints 1. Depending on your experience, assembly of this Play set should take approximately 6 to 12 hours after inventory of parts. Therefore, we recommend you set aside a full day for assembly. 2. Identify all of the parts for your Playcenter. Empty each box and lay out boards so you can see each part.
Suggested Playground Surfacing Playground equipment should never be placed on hard surfaces such as concrete or asphalt. Do not install loose fill surfacing over hard surfaces such as concrete or asphalt. Shredded bark mulch, wood chips, fine sand and fine gravel, are added as shock absorbing materials after assembly.
Operating Instructions: NOTE: Your children’s safety is our #1 concern. Observing the following statements and warnings reduces the likelihood of serious or fatal injury. Please review these safety rules regularly with your children. 1. This Playcenter is designed for the use of 6 occupants, per tower, who have a combined weight not exceeding 420 pounds, per tower, 4 occupants on the bridge, who have a combined weight of 280 pounds, 4 occupants on the swing area, who have a combined weight of 350 pounds, for a total unit cpacity of 20 occupants who have a combined total weight of 1,470 pounds.
Maintenance Instructions: 1. Check all nuts and bolts twice monthly during the usage season and tighten as required. (But not so tight that you crack the wood) We recommend you check the swing beam and hardware every two weeks due to wood expansion and contraction. It is particularly important that this procedure be followed at the beginning of each season.
Page 10
APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission’s Information Sheet for playground surfacing material Also see the following website for additional information: https://www.cpsc.gov/PageFiles/122146/324.pdf X3. CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS X3.1 The U.S.
Assembly Instructions Jungle Fun Swing Set Assembly Instructions WARNING: CHOKING HAZARD Unassembled parts may be a choking hazard to children 3 years and younger CAUTION: Adult Assembly Required. Hardware contains small pieces with sharp points. Keep parts out of the reach of children until assembled.
Page 12
Basic Setup Dimensions Place the set on level ground, not less than 6ft (1.83M) from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines or electrical wires. 33'-3" [10.1M] Important Assembly Notes Fig. i 1) While assembling unit, take time before and after each phase to make sure Fort is level.
Page 13
Parts Identification Wood Components (1)35/16X55/16X891/2SWINGBEAM-LA251a (2)1 X5 5/16X65SANDBOXBOARD-LK212 (2) 3 5/16 X 2 11/16 X 90 1/2 UPRIGHT - LD201 (2)1 X5 5/16X44 3/4SANDBOXBOARD-LK223 (2) 3 5/16 X 2 11/16 X 90 1/2 UPRIGHT - LD202 (2)1 X5 5/16X44 3/4SLIDEARCHRAIL-LK224 19 13/16 19 13/16 (4) 3 5/16 X 2 11/16 X 90 1/2 UPRIGHT - LD203...
Page 32
SANDBOX SEATS Phase Hardware Phase 10: & GUSSETS 2 1/2" Deck Screws (24) 1 3/4" Deck Screws (24) Phase Parts (8) 1 X 2 9/16 X 17 5/16 GUSSET - LN204 (4) 11/16 X 3 1/2 X 21 SANDBOX SEAT - LR294 MAKE SURE FRAME IS (4) 11/16 X 3 1/2 X 14 SANDBOX SEAT - LR295 SQUARE BEFORE...
Page 33
FLOOR BOARD Phase Hardware & BARRIER RAIL Phase 11: Fender Washer ATTACHMENT 1 3/4" Deck Screws 5/16" Split Washers (270) 5/16" T-nuts 5/16" x 4 1/4" Hex Bolts Phase Parts (38) X 39 3/8 FLOOR BRD. - LR243 11/16 X 1 1/4 X 23 5/8 FLOOR BOARD - LS113 (2) 11/16 X 1 1/4 X 39 3/8 FLOOR BOARD - LS112 11/16 (2) 1 5/16 X 3 1/2 X 64 7/16 BARRIER RAIL - LM283...
Page 34
Phase Hardware LOWER WALL RAILS Phase 12: 2 1/2" Deck Screws Fender Washer (24) 5/16" T-nuts 5/16" x 2 1/2" Lag Screws (12) (12) Phase Parts (2) 1 X 3 1/2 X 65 WALL RAIL - LM213 (4) 11/16 X 3 1/2 X 20 11/16 WALL RAIL- LR242 (4) 1 X3 1/2 X 11 WALL RAIL - LM226 (2) 11/16 X 3 1/2 X 64 7/16 WALL RAIL - LR282 (4) 1 X 3 1/2 X 7 WALL RAIL - LM227...
Page 35
Phase Hardware UPPER WALL RAILS Phase 13: 2 1/2" Deck Screws Fender Washer (24) 5/16" x 2 1/2" Lag Screws Phase Parts (4) 11/16 X 3 1/2 X 20 11/16 WALL RAIL - LR242 (2) 1 X 3 1/2 X 65 WALL RAIL- LM213 (2) 11/16 X 3 1/2 X 64 7/16 WALL RAIL - LR282 3"...
Page 36
SWING BEAM BRACE Phase Hardware Phase 14: Fender Washer & ARCH RAILS 5/16" Split Washers 5/16"x3 5/8"HexBolts (20) 2 1/2" Deck Screws 5/16" T-nuts 5/16" x 2 1/2" Lag Screws (16) (16) Phase Parts (2) 1 X 5 5/16 X 44 3/4 LAD./ROCKW ARCH RAIL - LK225 (1) 1 3/8 X 5 5/16 X 65 SWING BEAM CROSS BRACE- LF250 (2) 1 X 3 1/2 X 30 1/2 DOOR TOP RAIL - LM288 (2) 1 X 5 5/16 X 30 1/2 BRIDGE ARCH RAIL - LK287...
Page 37
TARP UPRIGHTS Phase Hardware Phase 15: & SUPPORTS 1 3/4" Deck Screws (42) Phase Parts 11/16 X 39 3/8 TARP END SUPP.. - LR234 (2) X 3 X 66 15/16 TARP UPRIGHT - LM230 (2) X 3 X 25 5/16 TARP UPRIGHT - LM231 X 37 3/8 TARP TOP SUPP..
Page 38
WALL SLATS Phase Hardware Phase 16: SIDES 1 & 2 1 1/8" Deck Screws (64) TARP UPRIGHT TYPICAL TYPICAL Phase Parts SPACING SPACING 2 3 4 2 3 4 (16) 5/8 X 3 1/2 X 23 5/8 WALL SLAT - LR240 REST ON FLOOR SIDES 1 &...
Page 43
SWING BEAM Phase Hardware Phase 21: ATTACHMENT 5/16" x 1 3/4" Hex Bolts Fender Washer 3/4" Deck Screws 5/16" Split Washers Phase Parts (1) PLACARD T-NUTS INSTALLED ON BACKSIDE IN PHASE 14: CENTER AND ATTACH PLACARD WITH 3/4" DECK SCREWS...
Page 44
HAND GRIP Phase Hardware Phase 22: ATTACHMENT 1/4 x 1 1/4" Machine Truss 1/4" Flat Washers 1/4" Split Washers 1/4" T-nuts Phase Parts (2 - PAIR) HAND GRIP - P002 1/4" X 1 1/4" MACHINE TRUSS SCREW 1/4" T-NUT 1/4" SPLIT WASHER 1/4"...
Page 45
STEERING WHEEL Phase Hardware Phase 23: & TARP ATTACHMENT 5/16" x 2 1/4" Hex Bolts 5/16" T-nuts Fender Washer 5/16" Split Washers 3/4" Tapping Screws (12) Phase Parts STEP 1: MARK CENTER OF BARRIER RAIL (2) FORT TARP (GREEN) - P005 (1) STEERING WHEEL - P001 AND DRILL THROUGH WITH 3/8"...
Page 48
Phase Hardware Phase Hardware BRIDGE ASSEMBLY Phase 26: 2" Deck Screws A2 (32) 2 1/2" Deck Screws A3 (8) Phase Parts (2) 1 1/2 X 3 1/2 X 60 ROPE RAILING SUPPORT - PF3836 (2) 1 X 3 1/2 X 13 1/2 LOWER STEP JOIST - PF3805 (2) 1 X 3 1/2 X 22 BASE-SHORT - PF3806 (2) 1 X 5 1/2 X 24 STEPS- PF3815 (2) 1 3/8 X 3 3/8 X 10 LOWER STEP SUPPORT - PF3834...
Page 49
Phase Hardware Phase Hardware BRIDGE ASSEMBLY Phase 27: 2" Deck Screws A2 (6) 2 1/2" Deck Screws A3 (24) Phase Parts (2) 1 1/2 X 3 1/2 X 26 1/4 ANGLED STEP SUPPORT - PF3835 (2) 1 3/8 X 3 3/8 X12 1/2 UPPER STEP JOIST - PF3803 (1) 1 3/8 X3 3/8 X 21 1/4 STEP -HE2 -PF3827 (2) 1 X 3 1/2 X 27 STEP-HE - PF3807 PF 3803...
Page 50
Phase Hardware Phase Hardware Phase 28: BRIDGE ASSEMBLY 2 1/2" Deck Screws A3 (8) Phase Parts (2) 1 X 5 1/2 X 24 STEPS- PF3815 2 1/2 1/2'' GAP STEP 1: WARNING: DO NOT ALLOW ANY CHILDREN ON THE PLAYSET UNTIL IT IS PF 3815 ANCHORED STEP 2:...
Page 51
Phase 29: BRIDGE ASSEMBLY B1 (4) 5/16" x 3 3/4" Tapping Screws Phase Parts #5/16TS3 3/4 (1) 3 5/16 X 3 5/16 X 39 1/8 BRIDGE SUPPORT - WZ3259 K1 (4) 5/16" Flat Washer 5/16FW STEP 2: STEP 1: 5/16 " Tapping Screws &...
Page 52
Phase Hardware Phase Hardware Phase 30: BRIDGE ASSEMBLY GREEN L-BRACKET 5/16” x 1 3/4" TappingScrews 1 1/4" Deck Screws #5/16TS1 3/4 L (8) A1 (4) M002 (4) 3/8" Flat Washer 5/16" x 1" Barrel Head Nut 5/16" Flat Washer Phase Parts K2 (4) K1 (4) D1 (4)
Page 53
Phase Hardware Phase Hardware BRIDGE ASSEMBLY Phase 31: 5/16" Flat Washer 5/16“ x 3 1/2" Eye Bolt K1 (4) J1 (4) 5/16" Lock Nut 5/16" Nut Cap G1 (4) P (4) STEP 3: Fig. 21 STEP 1: DRILL THROUGH UPRIGHT LD203 WITH 5/16"...
Page 54
Phase Hardware Phase Hardware Phase 32: BRIDGE ASSEMBLY 5/16" Flat Washer 5/16" x 3 3/16" Eye Bolt K1 (4) J3 (4) 5/16" Lock Nut 5/16" Nut Cap P (4) G1 (4) STEP 1: STEP 2: 5/16'' Washer 5/16"Nut Cap 5/16'' Loc Nut 5/16'' Washer 5/16"Nut Cap 5/16'' Loc Nut...
Page 55
Phase Hardware Phase Hardware BRIDGE ASSEMBLY Phase 33: P301 (11) Bridge Spacers O1 (1) Bridge Cable (1) 1 X 5 1/2 X 28 BRIDGE-C - PF3824 (1) 1 X 5 1/2 X 24 BRIDGE-K - PF3816 (1) 1 X 5 1/2 X 26 BRIDGE-G - PF3820 (1) 1 X 5 1/2 X 28 1/2 BRIDGE-B - PF3825...
Page 61
Phase Hardware Phase Hardware BRIDGE ASSEMBLY Phase 39: 5/16 x1 3/4'' Socket Pan- Head Bolt 5/16" Lock Nut (2) 25 33/55'' Lag Bolt Anchor-It G1 (2) E 5(2) Anchor-It and Tether 5/16'' Flat Washer Anchor-lt K1 (4) N (2) 3/8" STEP 2: 5/16"...
Page 62
BRIDGE ASSEMBLY Phase 40: 5 1/4 " " CEMENT " " " GRAVEL Bridge Platform dditional nchoring: Note: These instructions are for anchoring your unit in particularly sandy or otherwise loose soil. 1. Dig (2) holes for the Bridge Platform, (see pg. 46 for placement).
Page 63
Phase Hardware Phase Hardware ANCHORING Phase 41: 2 1/2" Deck Screws STAKE STAKE Phase Parts (6) - Plastic Stakes - P004 STAKE STAKE 2 1/2" Deck Screw Ground Board STAKE STAKE Note: Failure to use stakes can void warranty & cause injury. Final Step: Double check and make sure every bolt, screw and nut is tight.
Page 64
LIMITED WARRANTY Creative Cedar Design (CCD) offers many fun, interactive, and safe play sets. We only guarantee the original purchaser that this product is free of defects for 30 days from the date of purchase. The product registration card, along with a dated purchase receipt, must be returned to CCD within 30 days. Within a 30 day period, CCD will repair or replace, at our option, defective merchandise free of charge, provided that the defective part is a manufacturer’s defect and not seasonal check.
Page 65
Warranty claim procedure If you are confident that your play system has been installed and maintained properly, and you have a warranty claim, proceed with the following steps: 1. We will need copy of your proof of purchase (Vendor sales receipt only.) 2.
Page 66
PRODUCT REGISTRATION CARD Please complete this Product Registration Card along with a copy of the receipt and return to Creative Cedar Designs, within 30 days of original purchase in order to validate time of purchase for warranty. Or register at www.creativecedardesigns.com Name:________________________________________________________________ Address: _______________________________________________________________ City, State, Zip Code: ___________________________________________________...
Page 67
PRODUCT REGISTRATION CARD Please complete this Product Registration Card along with a copy of the receipt and return to Creative Cedar Designs, within 30 days of original purchase in order to validate time of purchase for warranty. FOLD HERE Place Stamp Here Creative Cedar Designs...