Summary of Contents for Ingenico IMP400
- Page 1 Intelligent Docking Station for iSMP2 Companion IMP400 Ingenico – 28-32 Boulevard de Grenelle 75015 PARIS Tél. 33(0)1 58 01 80 00 - Fax 33 (0)1 58 01 91 35...
- Page 2 5. Maintenance ________________________________________________ 13 5.1. Cleaning of the cradle ________________________________________________ 13 5.2. Transport and storage________________________________________________ 13 5.3. Troubleshooting _____________________________________________________ 13 5.4. Environment (WEEE, Batteries and Packaging) _________________________ 14 2/15 IMP400 Copyright © 2014 Ingenico 900021684 R11 000 01/0615 All rights reserved...
-
Page 3: Introduction
The IMP400 accessory has been designed for iSMP2 Companion product, do not attempt to use for any other use. Failure to comply with these instructions will void the manufacturer’s responsibility. -
Page 4: Unpacking
Unpacking ADVICE Carefully preserve the packaging of the IMP400. It must be re-used whenever the accessory is shipped. The following items are included in the IMP400 box : IMP400 Intelligent Docking Station for iSMP2 Companion This User guide POWER SUPPLY UNIT (PSU) -
Page 5: Recommendations
Recommendations 3.1. Security IMP400 is specially designed for iSMP2 Companion terminals charging. Do not short-circuit the metallic contacts. Do not attempt to open the product or the PSU. Do not attempt to replace the PSU by any other type even the characteristics are similar. - Page 6 Indicates that the product is only intended for use up to 2000m altitude Indicates that the product acts as a Limited Power Source (LPS) as per IEC60950-1 safety standard 6/15 IMP400 Copyright © 2014 Ingenico 900021684 R11 000 01/0615 All rights reserved...
-
Page 7: Ec Standard Compliance
Radio ETSI EN 300 328 v1.8.1 The CE marking indicates IMP400 complies with the requirements of European Directive 1999/5/EC of 9 March 1999 on Radio and Telecommunications Terminal Equipment for: The protection of the health and the safety of the user and any other person. -
Page 8: Main Characteristics
3.5. Main Characteristics The main technical characteristics of the cradle Ingenico IMP400 are: Mass 940 g Dimensions (Lxlxh) 400x122x66 mm Electrical mains network 100-240VAC / 50-60 Hz - Class I Ingenico ref: 296177532 –12Vdc/8A max PSU Models Operating conditions Ambient temperature -10°C to +45°C... -
Page 9: Installation And Connection
4.3. Positioning the cradle Install the IMP400 on a flat surface, with an easy access to an electrical outlet. Place the IMP400 away from any heat source and protected from dust, vibrations and electromagnetic radiations (away from video terminals, PC, anti-shoplifting barriers ...). -
Page 10: Cables Connection
If needed, plug the second Ethernet connector and clip the cable in the other cable guide, on the other side of the product. IMP400 ready to operate Put the IMP400 in place, and finally plug the PSU into the power outlet 10/15 IMP400 Copyright ©... -
Page 11: Fixing The Cradle On Its Support
4.5. Fixing the cradle on its support The IMP400 is equipped with keyholes fixations on the bottom in order to fix it to its support, if need be. Keyhole fixations on the IMP400 casing (bottom view) Location of the keyhole fixations The center distance between the two fixations is 340mm. -
Page 12: Charging Ismp
After that, approximate charging time is 3 hours to recharge the battery to full capacity LED indicators: Red: in charge Green: charged A battery indicator is provided on the iSMP screen, indicating the charge of the module. 12/15 IMP400 Copyright © 2014 Ingenico 900021684 R11 000 01/0615 All rights reserved... -
Page 13: Maintenance
Battery level is too low Check the PSU connections Check for iSMP positioning into the slot Check for electrical power network 13/15 IMP400 Copyright © 2014 Ingenico 900021684 R11 000 01/0615 All rights reserved... -
Page 14: Environment (Weee, Batteries And Packaging)
The associated symbol means that WEEE and waste batteries must not be thrown away but collected separately and recycled. Ingenico ensures that efficient collection and recycling schemes are set-up for WEEE and batteries according to the local regulation of your country. Please contact your retailers for more detailed information about the compliance solution in place for disposing of your old product and used batteries. - Page 15 INGENICO and the user. INGENICO is not responsible for any use of this device, which would be non consistent with the present document.