Advertisement

 
 
 
 
 

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MC348 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Magnavox MC348

  • Page 1          ...
  • Page 2 LOCATION OF CONTROLS:            Indicator  SET Button    Power On‐Off Button  Device selection Buttons  TV:            Television  VCR:            Video Cassette recorder  DVD:    DVD Player  CBL:     Cable box  SAT:     Satellite receiver  CD:      CD Player  Audio:    Audio device  Game: ...
  • Page 3 POWER SOURCE:    Install or replacing the batteries when it is drained as follows:  Slide out the battery door on the rear of remote then lift it up as the illustrated  below.  Install two (2) x AAA size batteries (not included) into the battery compartment as  the polarity markings inside it.  Close the battery door.            2 ...
  • Page 4 BATTERY PRECAUTIONS:  Follow these Battery Precaution when using a battery in this device:  1. Use only the size and type of battery specified.  2. Be sure to follow the correct polarity when installing the battery as indicated in the  battery compartment. A reversed battery may cause damage to the device.  3. Do not mix different types of batteries together (e.g. Alkaline and Carbon‐zinc) or old  batteries with fresh ones.  4. If the batteries in the device are consumed or the device is not to be used for a long  period of time, remove the batteries to prevent damage or injury from possible  battery leakage.  5. Do not try to recharge the battery not intended to be recharged; it can overheat and  rupture. (Follow battery manufacturer’s instructions.)  6. Do not dispose of battery in fire. Battery may explodes or leak.  7. Clean the battery contacts and also those of the device prior to battery installation.    SETTING UP:    You must set up the Universal Remote before operating with your device as follows:  Setup with device code:  1. Use only the size and type of battery specified.  2. Power on your desired device (EX: TV) as usual.  3. Find the four (4) digit device code for it in the attached Code List.  Press and release the corresponding device’s selection button on the Universal  Remote (EX: TV Button).    Press and hold the SET Button approximately 3 seconds until the LED Indicator is  illuminated then release the button.  Enter the four (4) digit code for your device by pressing the numeric buttons. The LED  Indicator will turn off. (If the code is invalid, the Indicator will stay illuminated. Repeat  the setting procedures from 2‐5 again to reset a valid code.)  Aim the Universal Remote to the remote sensor for your device then try operating the ...
  • Page 5 Setting with the brand name code:  1.  Find the single digit brand code of your device on the attached Brand Name Code  List.  2. Power on your desired device (EX: TV) as usual. Aim the Universal Remote to the  remote sensor for you device.  3. Press and hold the corresponding device’s button and the numeric button of the  brand code of your device at the same time. (For example: Press and holding the  “TV” and “1” Buttons at the same time.)  4. Wait approximately 2 seconds, the LED Indicator will start blinking.  5. Release the numeric button and keep holding the device button. A different infrared  signal of “Power off” is sent every 0.5 second.  6. Once your device is shut off, release the device button immediately to save the  setting and exit.  7. Aim the Universal Remote to the remote sensor for your device then operation the  device with the Universal Remote. If the device is responds correctly, it means you  have right settings. Otherwise, set again starting from step 3 or try the following  setting methods.    Auto Setting:  1. Power on your desired device (EX: TV) as usual.  2. Press and release the corresponding device’s selection button of your device (EX: TV  Button).    3. Press and holding the SET Button approximately 3 seconds until the LED Indicator is  illuminated then release the button.  4. Aim the Universal Remote to the remote sensor for your device then press and  release the POWER Button. A different infrared signal of “Power off” is sent every 0.5  second.  5. Once your device is shut off, press the OK Button immediately to save the setting and  exit. ...
  • Page 6 Manually setting:  Power on your desired device (EX: TV) as usual.  Press and release the corresponding device’s selection button for your desired device  (EX: TV Button).    Press and hold the SET Button approximately 3 seconds until the LED Indicator is  illuminated then release the button.  Aim the Universal Remote to the remote sensor of your device (EX: TV) then press  the CH + or – buttons on the Universal Remote repeatedly to send different infrared  signals; LED Indicator will blink.    Once your device is shut off, press the OK Button to save the settings and exit, the  LED Indicator will turn off.  Aim the Universal Remote to the remote sensor for your device (such like TV) then  operation the device with the Universal Remote.    OPERATION:    1. Repeat the setting procedure until all desired devices (up to 8 devices) was been set.  2. Press the desired device selection button (EX: TV) on the Universal Remote.  3. Aim the Universal Remote to the remote sensor of you device then operation the  device with the Universal Remote.    NOTES:  1. Buttons may be titled differently on your Universal Remote from the titles on the  original manufacturer's controller.  2. Some of buttons may not respond as your original remote.  3. If the Universal Remote is halt, abnormal operation or you wants to reset all settings.  Reset the Universal Remote by take out all batteries approximately 1 minute then  reinstall the batteries.           ...
  • Page 7 4. Remote Distance:    Remote sensor of your desired device     Remarks:    A. When there is an obstacle between the device and the Universal Remote, the    transmitter may not operate.    B. When in direct sunlight, an incandescent lamp, fluorescent lamp or any other    strong light shines on the remote sensor of the device, the remote operation may    be unstable.      6 ...
  • Page 8: Troubleshooting

    TROUBLESHOOTING:    Check the following before requesting service:    SYMPTOM  POSSIBLE CAUSE  POSSIBLE SOLUTION  Batteries incorrect installation    Re‐install the batteries as the  polarity marking inside the  No power  battery compartment  Batteries drained  Replace by new batteries  The Universal Remote had not set or  Reset the Universal Remote  Not functioning  incorrect set    as instructed earlier      GERNERAL SPECIFICATTIONS:    Power Source: ……………… 2 x AAA size batteries (Not included)  Effective Range ……………. Approximate 15 feet (5M) in open area      ACCESSORIES:    1 x User’s Manual    1 x Remote Code List               ...
  • Page 9  ...

This manual is also suitable for:

Mc345

Table of Contents

Save PDF