Advertisement
high performance modular system - endless possibilities for flow
Combining versatile flowtoys LED light units – the flowlight and the capsule light – and a
series of click-in caps, connectors and tubes that are interchangeable, the modular system
enables the creation of almost any illuminated prop imaginable.
Gone are the days of wondering how to check in our 5' staffs for travel, or deciding which
flowtoys to bring to an event. Now with just a few lights, tubes, caps and leashes, you can
have 4' double staffs that quickly transform into a contact staff, a couple of 3' staffs, clubpoi,
swinging clubs, chucks and more, and everything fits in a backpack!
The world just became a little more awesome for us, because of the versatility, creativity
and fun the Flowtoys Modular System enables. We hope that it will bring more flow and
more awesome to your life!
QUICK START GUIDE: THINGS TO KNOW BEFORE YOU FLOW
1. Do not use glowsticks or WD-40 with tubing. While polycarbonate is very strong, it breaks down
in the presence of certain esters, including those produced by chemical glowsticks, mineral spirits and
WD-40. Do NOT put chemical glowsticks into the tubes, otherwise they can become brittle and
shatter. We recommend lubricating the ends of your tubes with a touch of petroleum jelly.
2. Be careful when using your flowtoys in the presence of sand or grit!
Sand and grit can get inside your caps and connectors and make them difficult to use. If you're using
flowtoys in a sandy area, blow out/clean your caps and connectors of sand before attaching them to
the tubing. If your caps and tubes feel gritty, clean them and apply a bit of vaseline for lubrication.
3. Make sure all caps and connectors are fully secured before use! Check that the buttons in your
caps and connectors are fully clicked into the holes of the tubes.
4. Cleaning your flowtoys. If your flowcaps, connectors, crystal cases or flowmass get dirty after
hours of practice in the park, flowing in the forest or rockin' it on a dancefloor, clean them with soap
and warm water, or put them in the wash with your laundry: air-dry, no heat!
Flowtoys are designed to last you a lifetime, but nothing is indestructible,
so we provide this warranty to enable you to freely find your flow*.
If you manage to break a flowtoys product, we have a policy of free
replacement on damaged non-electronic parts and defective electronics,
and 50% off replacement on broken electronics. If the tips in this guide do
not keep your flowtoys working for years to come, please contact us!
* Flowtoys reserves the right to refuse coverage to anyone abusing this warranty.
Please contact us before sending in your product, or it may be returned to sender.
Modular System Guide
LIFETIME WARRANTY
features
operating instructions
troubleshooting
inspiration
1
Advertisement
Table of Contents
Related Manuals for Flowtoys Modular System
Summary of Contents for Flowtoys Modular System
-
Page 1: Operating Instructions
Gone are the days of wondering how to check in our 5’ staffs for travel, or deciding which flowtoys to bring to an event. Now with just a few lights, tubes, caps and leashes, you can have 4’ double staffs that quickly transform into a contact staff, a couple of 3’ staffs, clubpoi,... - Page 2 FLOWMASS: These translucent crystalline-looking weights add more inertia to your flow and optimize the balance of your flowtoy. They can be added to crystal cases and flowtoys 1” tubing. Add two or more if you like your tools heavy! KNOB-LEASH: Adjustable integrated leash with knob handle and minimal hardware.
- Page 3 FLOWTOYS MODULAR SYSTEM - INSTRUCTIONS INSTRUCTIONS FOR LIGHTS Modular system props are compatible with both flowlights and capsule lights - instructions for your lights are included in a separate manual with your prop. CAPS :: FLOWCAP Your tube-based props come standard with flowcaps. The flowcap is compatible with both flowlights and capsule lights, and securely clicks into any flowtoys 1”...
- Page 4 Some older versions do not separate in a way that would allow this link to work prop- erly. Please check our web support page for details. If your capsule is not compatible, contact us at support@flowtoys.com. CONNECTING FLOWLIGHT TO FLOWLIGHT: If you have two or more flowlights in one tube, you will need to attach the opposite ends of the flowlight to each other for the lights to fit properly, and slide in and out of the tubes properly.
- Page 5 INSTRUCTIONS FOR POI, DARTS & OTHER LEASH-BASED PROPS KNOB-LEASH + CORD CONNECTOR Your tubing-based poi and darts come with an integrated leash system made of “flowcord” - the first cord engineered for poi spinning with perfect smoothness and optimal give. Your knob-leash comprises a pair of knob handles w/ a washer and extra flowcord to adjust your leash length, and connects to tubes via a cord connector with 2mm hex head screws.
- Page 6 BEFORE USE: Check for damaged parts before using any product. Ensure caps, connectors and battery doors are fully secured. Most flowtoys are made of individual pieces that can separate during use if not properly assembled.
Need help?
Do you have a question about the Modular System and is the answer not in the manual?
Questions and answers