Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for U-Reach UB300
- Page 1 UB300 Flash Duplicator User Guide 33MB 33MB 1 Sec. 1 Sec. 2 Sec. 2 Sec. 3 Sec. 3 Sec. Per Second Per Second Real Capacity Real Capacity Flash Speed Flash Speed Data Copy Data Copy Check Check Check Check Check...
- Page 2 CONTENT I. Product Introduction ...................... 1. Overview ........................2. Features ........................3. Package Content ....................... 4. Basic Instruction ....................... 5. Function Table ......................II. Function Introduction ..................... 1. Copy .......................... 2. Compare ........................3. Copy & Compare ...................... 4. Utility ........................4.1 Device Info.
-
Page 3: Package Content
4. Lightweight design and user friendly with instant power on and off. 5. Support multiple Flash media: it enables you to copy multiple Flash media of SD, MS, CF through a qualified USB interface card reader. 3. Package Content UB300 Adapter... -
Page 4: Basic Instruction
4. Basic Instruction A. System Overview Forward USB Master port Backward USB Target port Signal LED B. Back side Power Switch and Plug of the Power Supply Power supply Power switch C. LCD Configuration Total Content Size Copy 870M Copy progress Copied Size 0:20 275M... -
Page 5: Function Table
5. Function Table Function Description 1. Copy USB/SD/Micro SD/CF Flash copy. This option makes bit-by-bit comparison between the master source and all other copied flash 2. Compare cards. This option will make a copy first and then compare the copied Flash devices with the source 3. Copy+Compare immediately after the copy has finished. 4.1 Device Info. This function will show Flash device’s general information includes capacity, format and data size. 4.2 Chk USB Virus To check USB VIRUS in Flash 4.3 Capacity Check To check Flash device’s real capacity. -
Page 6: Ii. Function Introduction
II. Function Introduction 1. Copy It copies data from source Flash device to target Flash devices. The default setting of copy area is “Data Only”. If you like to change copy area from “Data Only” to “ Whole HDD” or “All Partitions”, please refer to function [5.1 Copy Area] for selecting the copy modes Steps of copy: Plug source and target Flash devices into duplicator→Select [1. Copy]→Press... -
Page 7: Compare
2. Compare It is used to check if the data on source Flash device is identical to the copied Flash devices after duplication. Steps of compare: Plug Flash devices into duplicator→Select [2. Compare]→Press [OK]→Compare Processing→Compare finished→ Press [ESC] to finish compare. USB Duplicator 3817M Compare 870M 2. Compare Reading Content 0:20 275M... -
Page 8: Utility
4. Utility 4.1 Device Info. This function will show Flash device’s general information includes capacity, format and data size. Steps of Show Flash device’s Info.: 1. Plug Flash devices into duplicator→Select [4. Utility ]→Press [OK]→Select [4.1 Device Info. ]→Press [OK]→System shows the info. USB Duplicator [Utility] [#01]... -
Page 9: Capacity Check
USB Duplicator [Utility] Pass:0 C-Virus 4. Utility 2. Check USB Virus Fall:1 Forward 2. Press [Forward] / [Backward] to check other Flash devices’ virus→Press [#01] SIZE:3817M Could be Vrius! [ESC] to finish Flash without virus Pass:0 C-Virus Flash with virus Number of Flash in process Fall:1 4.3 Capacity Check... -
Page 10: Measure Speed
Steps of formatting Flash device: 1. Plug Flash devices into duplicator→Select [4. Utility ]→Press [OK]→Select [4.4 Format FAT]→Press [OK]→System format the Flash devices USB Duplicator 4. Utility Do Farmat 4. Utility 4. Format FAT Confirm? Pass:2 Format Fall:0 2. Press [Forward] / [Backward] to check other Flash devices’... -
Page 11: System Info
4.6 Erase Content This function is to erase Flash device’s FAT data content, it will not erase the Flash FAT16/32 format. If format is not FAT16/32, ie. NTFS, the quick erase will not execute. ** The source port (port #1) does not execute erase function. Steps of erasing Flash device’s content: 1. -
Page 12: Setup
5. Setup 5.1 Copy Area There are two options for copy: Only Data Area and Whole Media. 5.1.1 Only Data Area: This function is to set the copy mode to copy data area only. It is faster than copy whole Flash. It will automatically analyze the source Flash device’s file format. If the format is FAT16,32/NTFS/Linux (Ext2, Ext3) which is recognizable by the system, it will copy the data only instead of copy the whole Flash. -
Page 13: Iii. Faq
Q2: Can I copy USB devices with big different capacity ? (For example 4GB to 1GB) A2: Yes, UB300 will copy whatever the capacity size is. However, to avoid an unexpected poor quality of data duplication, it is strongly recommended that target and source have to be the same of capacity. - Page 14 ● Some USB HDDs need to plug 2 USB power supply to keep a stable power supply (some USB HDDs may not need to use both of the 2 USB power supply). USB HDD USB Power Supply USB Power Supply ● The number of USB ports on UB300 may not enough for copying USB HDD while the USB HDD needs both of 2 USB power supply plug to the duplicator.
-
Page 15: Iv. Specification
IV. Specification Model UB300 Target Operation Stand alone USB1.1 / USB2.0 Support media SD / SDHC / Micro SD / MMC / Mini SD / CF (by USB multimedia card reader) Display 2*16 Monochrome LCD display Control Button 4 push buttons ( Forward , Backward, OK, Esc)