1. Manuals
  2. Brands
  3. Smartwatch Manuals
  4. Camcorder
  5. H20TVISD302
  6. Quick start manual

Smartwatch H20TVISD302 Quick Start Manual

Hd-tvi speed dome
Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the H20TVISD302 and is the answer not in the manual?

Questions and answers

Summary of Contents for Smartwatch H20TVISD302

  • Page 2 HD-TVI Speed Dome·Quick Start Guide Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. This manual applies to HD-TVI Speed Domes. This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice.

  • Page 3: Regulatory Information

    HD-TVI Speed Dome·Quick Start Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 4 HD-TVI Speed Dome·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
  • Page 5 HD-TVI Speed Dome·Quick Start Guide  Do not aim the speed dome at the sun or extra bright places. A blooming or smear may occur damaging the camera.  Please use the gloves provided when handling the dome cover, avoid handling the dome cover with bare hands.
  • Page 6 HD-TVI Speed Dome·Quick Start Guide Table of Contents 1.1 Connection Diagrams ..................1 1.2 DIP Switch Settings ..................2 1.2.1 H20IPSDIR302 IR Speed Dome Settings ................. 4 1.3 Installation ..................... 6 1.3.2 Installing the Bracket ......................6 1.3.1 Setting the DIP Switch ......................7 1.3.2 Installing the Speed Dome .....................

  • Page 7: Connection Diagrams

    HD-TVI Speed Dome·Quick Start Guide 1 Installation Before you start: Check the package contents and make sure that the device is in good condition and all parts are included. 1.1 Connection Diagrams Please turn the power off before connecting the cables. The cable connections are shown in the following figure.

  • Page 8: Dip Switch Settings

    HD-TVI Speed Dome·Quick Start Guide H20TVISD302 ① AC24V ① AC24V CVBS Video Output YELLOW/GREEN GND BLACK AC24V HD-TVI Video Output RS485 ② ② YELLOW R485- Alarm ORANGE R485+ Figure 1-2 Cables of Other Speed Dome Table 1-2 Cables Description Name...
  • Page 9 HD-TVI Speed Dome·Quick Start Guide DIP Switch Figure 1-3 DIP Switch Settings for 5-inch Outdoor Speed Dome Figure 1-4 Enlarged View of DIP Switch Address Settings The SW1-switches from 1 to 8 are used for setting the address of speed dome. You can refer to Table 1-3 for details of setting the speed dome address.

  • Page 10: H20Ipsdir302 Ir Speed Dome Settings

    HD-TVI Speed Dome·Quick Start Guide 2400 4800 9600 19200 1.2.1 H20IPSDIR302 IR Speed Dome Settings Two DIP switches SW1 and SW2 are for setting the speed dome address, baudrate, protocol, etc., with value ON=1 and OFF=0. The switch label is on the back of the SWITCH cover as shown in Figure 1-5.
  • Page 11 HD-TVI Speed Dome·Quick Start Guide Dome Address Baudrate Settings The No. 1, 2 and 3 of SW2 switch are for setting the baudrate of the speed dome, standing for 2400bps, 4800bps and 9600bps respectively. The baudrate will be set as 2400bps by default if it is out of this range.

  • Page 12: Installation

    HD-TVI Speed Dome·Quick Start Guide Switch No. Description Turn on the resistor Turn off the resistor 1.3 Installation 1.3.2 Installing the Bracket Before you start:  The wall must be thick enough to take the expansion screws.  Please make sure that the wall is strong enough to withstand more than 8 times the weight of the dome.

  • Page 13: Setting The Dip Switch

    HD-TVI Speed Dome·Quick Start Guide Figure 1-9 Secure the Mount 5. Install the speed dome to the wall bracket. Please refer to Section 1.3.2 Installing the Speed Dome for installation details. 1.3.1 Setting the DIP Switch Set the address and baudrate for the speed dome. The default value of the DIP switch is shown below: ...

  • Page 14: System Application

    Speed Dome Monitor Figure 2-1 System Application  If using a SmartWatch HD-TVI speed dome with a SmartWatch HD-TVI recorder, PTZ/OSD can be accessed from the HD-TVI DVR without the RS485. 2.2 Basic Operations Make sure the speed dome is connected correctly, and the following basic operations are working: Panning and tilting: Click the direction buttons to control the pan and tilt movement of the speed dome.

  • Page 15: Configuring Patrol

    HD-TVI Speed Dome·Quick Start Guide MAIN MENUS <SYSTEM INFO> <DOME SETTINGS> <RESTORE SETTINGS> <RESTORE CAMERA> <REBOOT DOME> <LANGUAGE> ENGLISH EXIT Figure 2-2 Main Menu Please refer to the user manual for more detailed instructions on the camera OSD. 2.2.1 Configuring Patrol You can configure the patrol function from the DVR.
  • Page 16 HD-TVI Speed Dome·Quick Start Guide Figure 2-4 Key point Configuration 4. Configure key point parameters, such as the key point No., duration of staying for one key point and speed of patrol. The key point corresponds to the preset. The Key Point No. determines the order at which the PTZ will follow while cycling through the patrol.
  • Page 17 HD-TVI Speed Dome·Quick Start Guide Up to 8 patrols can be configured. 3. Edit the patrol. 1). Move the cursor to EDIT PATROL and click IRIS+ to enter edit mode. NUM PST DWELL SPEED IRIS+ OK IRIS- CANCEL Figure 2-6 Edit the Patrol 2).

  • Page 18: Configuring Park Actions

    HD-TVI Speed Dome·Quick Start Guide 2.2.2 Configuring Park Actions Predefined park actions (scan, preset, patrol and etc.) can be configured to start automatically after a period of inactivity (park time).  Configuring Park Actions by DVR Steps: 1. Click the button PTZ in the lower-right corner of the PTZ setting interface; Menu>Camera>PTZ 2.
  • Page 19 HD-TVI Speed Dome·Quick Start Guide MOTION AUTO FLIP PROPORTIONAL PAN PARK TIME PARK ACT NONE SCAN SPEED IMAGE FREEZE DOME SPEED BACK EXIT Figure 2-8 PTZ Configuration 2. Move the cursor to the PARK TIME, and set the value in the range from 5 to 720 seconds. 3.

This manual is also suitable for:

H20tvisdir302

Table of Contents