Summary of Contents for WallboxOK EV PORTABLE TYPE1
- Page 1 WALLBOX EV PORTABLE USER MANUAL INSTALLATION MANUAL Online Manual http://goo.gl/lL2jI1...
- Page 2 WALLBOXOK bears the CE mark. The corresponding Declarations of Conformity are located at WallboxOK. This product metes the requirements of the ROHS Directive (2011/65/CE). The corresponding Declarations of Conformity are located at WallboxOK Disposal information The above symbol indicates the selective collection of electrical and...
- Page 3 SPECIFICATION FOR THE ELECTRICAL CONNECTION ............. 12 Dear Customer,, The WallboxOk team, want to thank you for buying one of our Electric Vehicle Charging Box. Our passion in design and innovation makes our charging points leaders in technology. Do not hesitate to contact us at info@wallboxok.com if you have any suggestion.
-
Page 4: Important Information
WARNING! Not observing the safety instructions can result in risk of death, injuries and damage to the device! WALLBOXOK assumes no liability for claims resulting from this. Electrical hazard / fire hazard! Never use damaged, worn or dirty charging plugs. - Page 5 Make sure that the load cable is not damaged by mechanical damage (bending, snagging or crushing) and that the contact area is not exposed to dirt, water or heat sources. WARNING! Risk Damage! Never clean the charging station using spray water (from a hose, high-pressure cleaner etc.) to clean the charging station! INTENDED USED THE EV PORTABLE is a "charging station"...
-
Page 6: Overview
OVERVIEW. VERSION OVERVIEW WALLBOX EV PORTABLE AMPS RATE BUTTONS LCD DISPLAY CHARGING Cable IEC 62196 o SAE J1772 CEE PLUG VERSIONS VERSIONS Model Intensity Power Supply Connector Input Types of Connector Type1 16 Amp Max 3,7 kW 1F+N+TT CEE 16 Amp SAE J1772 16Amp. -
Page 7: Using De Charging Station
USING DE CHARGING STATION. CONCONNECT ELECTRICAL CHARGING POINT 1. Plug CEE industrial conector. If necessary you can use the adapters. 2. Wait a few seconds and select the Amp rate with the buttons. PLEASE READ BEFORE SECTION 4.1 “AMPS RATE SELECTION”! 3. - Page 8 SELECT YOUR AMP RATE DEPENDING ON THE ADAPTOR CHOOSEN. Amps range permited Charging power (máximum) IEC 62196: 22 kW 6-32 Amp. SAE J1772: 7,6 kW CETAC 32 AMPERIOS 400V IEC 62196: 7,6 kW 6-32 Amp. SAE J1772: 7,6 kW CETAC 32 AMPERIOS 230V IEC 62196: 11 kW 6-16 Amp.
- Page 9 4.3 TROUBLESHOOTING. A series of parameters can be modified in the equipment menu. To access the menu we will follow the following procedure: Without connecting the electric vehicle (idle mode), press the 2 buttons simultaneously. Press until the menu is accessed. It is necessary between 3-4 seconds. Press 3-4 seconds until the menu is accessed You can scroll through the menu with the right - left buttons.
- Page 10 TROUBLESHOOTING.. PROBLEM Possible cause LCD Display does not light up No voltage supply. Check RCD circuit breaker and line circuit breaker and switch on if necessary. Defective – please contact your service partner Charging procedure is not started The plug is not inserted correctly - Pull out the plug and insert the plug again.
-
Page 11: Installation Guidelines
INSTALLATION GUIDELINES. GENERAL CRITERIA FOR THE SELECTION OF THE LOCATION WHERE TO INSTALL THE CHARGER The recharging point has been built for interiors and exteriors. So it is necessary to foresee the build conditions and the protection of the build location. ... - Page 12 INDICATIONS FOR ELECTRICAL CONNECTION. GENERALITIES The electric charging station is intended for connection to a cetac outlet. You must select the recharge intensity according to the chosen adapter. The plug where the PORTABLE EV is connected will have an existing power line with a fixed cable and must comply with the current national legal provisions.