1. Manuals
  2. Brands
  3. Digital Monitoring Products Manuals
  4. Receiver
  5. 1100DI
  6. Installation manual

Digital Monitoring Products 1100DI Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Description

The 1100DI Wireless Receiver provides up to 16 wireless zones for XRSuper6 and XR20 Command Processor™ panels
and up to 32 wireless zones (28 zones using one keypad) for XR40 Command Processor™ panels. The 1100DI is
compatible with all DMP wireless devices. The 1100DI provides two-way, supervised communication using 900 MHz
frequency hopping-spread-spectrum technology. The receiver can be installed anywhere on the panel keypad bus.

What is Included

The 1100DI Wireless Receiver includes the following items:
• One Model 1100DI Wireless Receiver
• One 4-wire Harness
• Hardware pack

Compatibility

The 1100DI Wireless Receiver is compatible with any XRSuper6, XR20, or XR40 Command Processor™ panels using
firmware Version 300 or higher. In addition to firmware Version 300 or higher, XR20 Command Processor™ panels
need to be hardware Level L or higher released October 2000. No specific receiver programming is required. Once
installed, a panel programmed with wireless information will automatically recognize the wireless receiver.

Installing the 1100DI Wireless Receiver

The 1100DI Wireless Receiver can be mounted anywhere along the panel keypad bus. A location should be selected
that will be centrally located between the 1100 Series transmitters used in the installation. Install the receiver
away from large metal objects. Mounting the receiver on or near metal surfaces impairs performance. Do not used
shielded wire between the panel and receiver. When selecting the proper mounting location and operation, refer to
the LED Survey Operation section of the specific installation guide for the transmitter being installed.
Wire
opening

Installing the Receiver behind a Keypad

The following instructions cover installing the receiver inside the wall behind the keypad. If the installation requires
the receiver to be mounted, refer to Installing the Optional Mounting Bracket or Installing the Receiver without the
Mounting Bracket.
1. Remove the cover from the plastic housing by squeezing both sides toward each other.
2. Connect the receiver to the panel keypad bus using the supplied 4-wire harness. Route the wires through the
opening in the back of the housing.
3. Snap the cover back in place and suspend the receiver inside the wall behind the keypad. Do not install the
receiver inside of a gang box.
INST ALLA TION GUIDE
1100DI Wireless Receiver
Figure 1: Receiver PCB
Keypad Bus
header

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1100DI and is the answer not in the manual?

Questions and answers

Summary of Contents for Digital Monitoring Products 1100DI

  • Page 1: What Is Included

    The 1100DI Wireless Receiver provides up to 16 wireless zones for XRSuper6 and XR20 Command Processor™ panels and up to 32 wireless zones (28 zones using one keypad) for XR40 Command Processor™ panels. The 1100DI is compatible with all DMP wireless devices. The 1100DI provides two-way, supervised communication using 900 MHz frequency hopping-spread-spectrum technology.
  • Page 2 Code (1-50). In Zone Information, program the wireless zones. 1100DI Receiver Operation The 1100DI receiver automatically sends the panel house code to wireless transmitters when the unique transmitter serial number is programmed into the panel. The house code identifies the panel, receiver, and transmitters to each other.

  • Page 3: Led Operation

    Refer to the XRSuper6/XR20/XR40 Programming Guide (LT-0305) for complete wireless programming information. Note: When any wireless input zone for a particular address is programmed (Ex: 11-14 = Addr 1), the 1100DI responds to the panel for this address. Other devices, such as keypads or hardwired zone expanders, cannot use this address.
  • Page 4 • Verify what zone numbers are assigned as wireless zones and check the address settings of other device(s) connected to the keypad bus to ensure no duplicate addresses have been used. • Verify the 1100DI LEDs are operating as listed in 1100DI LED Operation on the previous page. • Verify transmitters have batteries correctly inserted.
  • Page 5 PIR Motion Detector 1125 PIR Motion Detector 1129 Glassbreak Detector 1139 Wireless Bill Trap 1142 Two-Button Hold-Up Transmitter 1145, 1146, 1147 Four, Two, or One-Button Key Fobs 1161, 1162 Residential Smoke Detector Digital Monitoring Products 1100DI Wireless Receiver Installation Guide...

  • Page 6: Fcc Information

    FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Table of Contents