CDV Group CA-A470-A Instruction Manual

2-Door expansion module CA-A470-A
instruction manual
introduction
connected to the ct-V900 controller's expansion
bus, maximum 3 per controller, the 2-Door
Expansion module (cA-A470-A) supports two
readers, two BcD keypads, four zone inputs, 6
outputs and two locking devices.
Specifi cations
Readers: connect 2 per module
Keypads: connect 2 per module
Inputs: 4 standard without ATZ, 1 tamper
Outputs: 6 (open collector) 25 mA Sink
Lock Outputs: 2 lock outputs (Form C relays)
each: 15A @ 28VDC (resistive)
AC Power: 16VAC, 40VA max.
Frequency: 50Hz/60Hz
Aux. Current: 500mA (max.)
Battery: 12VDC, 7Ah
low battery = 10.2VDC
low battery restore = 12.2VDC
low battery cut-off = 8.5VDC
Communication: expansion bus (E-Bus), RS-485,
Plug and Play, 3 modules per CT-
V900-A
Operating temp.: 5 o C to 55 o C (411 o F to 133
Dip Switches
In order for new DIP switch settings to take
effect, the 2-Door Expansion module's power
must be disconnected and then reconnected.
Assign Address (1 and 2)
DIP switches 1 and 2 determine the 2-Door
Expansion module's address in the
network, regardless of the order that they
are connected to the controller. centaur
recognizes the doors according to the DIP
switch settings as shown in Figure 1.
Figure 1: Setting the network address
CT-V900
EOL
Door 1
CA-A470-A
Position Technology CA - A470 - A
AC
AC
D1NC LOCK#1 BAT+
COM STATUS AC OK BAT-
D2NC D1NO AUX OK V+ V+
COM LOCK#2 JP120 CHECK BATT COMM V-
D2NO 350mA/700mA BATT TRBL V-
SW1 SWITCH ADD 1 2 BACKUP 1 OUT5 OUT6
SW2 ADD 2 0 NO CARD 0
Z1 SW3 SW4 ADD 8 ADD 4 0 1 ALL CARDS 2 CARDS 0 1
COM SW6 SW5 BACKUP1 BACKUP2 1 UNLOCK DOOR 1 EOL A+ B- LOW
Z2 SW7 PULSE 5&6 HIGH A+
Z3 COM SW8 N/D GND B-
Z4 READER#2 READER#1 TAMPER
DATA DATA TAMPER
TX RX E-BUS
Door 4 Door 3
CA-A470-A
Position Technology CA - A470 - A
AC AC
D1NC LOCK#1 BAT+
COM STATUS BAT-
D2NC D1NO AC OK AUX OK V+ V+
COM LOCK#2 JP120 COMM CHECK BATT V-
D2NO 350mA/700mA BATT TRBL V-
SWITCH BACKUP OUT6 OUT5
SW2 SW1 ADD 2 ADD 1 0 2 0 1 NO CARD
Z1 SW3 SW4 ADD 4 ADD 8 1 0 2 CARDS ALL CARDS 1 0
COM SW5 BACKUP1 1 1 UNLOCK DOOR EOL A+ B- LOW
Z2 SW7 SW6 PULSE 5&6 BACKUP2 HIGH A+
Z3 SW8 N/D GND B-
Z4 COM READER#2 READER#1 TAMPER
DATA DATA TAMPER
E-BUS TX RX
Door 6 Door 5
CA-A470-A
Position Technology CA - A470 - A
AC AC
D1NC LOCK#1 BAT+
COM STATUS BAT-
D2NC D1NO AUX OK AC OK V+ V+
COM LOCK#2 JP120 CHECK BATT COMM V-
D2NO 350mA/700mA BATT TRBL V-
SWITCH BACKUP OUT6 OUT5
SW2 SW1 ADD 2 ADD 1 2 0 NO CARD 1 0
Z1 SW3 SW4 ADD 4 ADD 8 1 0 1 0 2 CARDS ALL CARDS
COM SW5 BACKUP1 1 UNLOCK DOOR 1 EOL A+ B- LOW
Z2 SW6 SW7 PULSE 5&6 BACKUP2 HIGH A+
Z3 SW8 N/D GND B-
Z4 COM READER#2 READER#1 TAMPER
DATA DATA TAMPER
E-BUS TX RX
Door 8 Door 7
lock State during Communication Failure
DIP switches 3 and 4 determine the state
of Lock #1 and Lock #2 oNLY during a
communication failure between the 2-
Door Expansion module and the controller
(ct-V900-A). Normally, the lock outputs
follow the Lock control for the ct-V900-A.
therefore, the DIP switches should have the same
setting as the Lock control for the corresponding
doors in centaur.
Lock #1 = DIP switch 3
Lock #2 = DIP switch 4
oFF =
De-energized:
During a communication failure, the normal
o F) state of the lock output is De-energized.
When Lock #1 or Lock #2 is activated,
power is applied to the corresponding
lock output to unlock the door. Activation
depends on the setting of the DIP switches 5
& 6 (Access during communication Failure).
on =
Energized:
During a communication failure, the normal
state of the lock output is Energized.
When Lock #1 or Lock #2 is activated,
power is removed from the corresponding
lock output to unlock the door. Activation
depends on the setting of the DIP switches 5
& 6 (Access during communication Failure).
De-energized: no power in normal state;
requires power to activate.
energized: power in normal state; remove
power to activate.
Access during Communication Failure (5 and 6)
DIP switches 5 and 6 determine the
access to the protected doors during a
communication failure.
Door 2
Address 1
Switch Setting
Add 1 =
OFF
Add 2 =
OFF
"No card"
5 = off (0)
Access is denied to all cards and doors
6 = off (0)
are locked until communication is restored.
"2 cards"
5 = on (1)
Access is granted only when 2 cards of
Address 2
6 = off (0)
a valid format are presented to the reader.
Add 1 =
ON
Add 2 =
OFF
"All cards"
5 = off (0)
Access is granted when any card with
6 = on (1)
a valid format is presented to the reader.
"unlock Door"
5 = on (1)
Address 3 Doors are unlocked until communication
6 = on (1)
Add 1 =
is restored.
OFF
Add 2 =
ON
Activate output on Communication Failure (7)
DIP switch 7 determines if out5 and
out6 will pulse during a communication
failure. When DIP switch 7 placed in the
"oN" position, the outputs on the device(s)
connected to the out5 and out6 terminals
will pulse. For example, the buzzer on
the reader can pulse to advise users that a
communication failure has occurred.
Dip Switch (8)
For future use.
eol Jumper
Place the EoL jumper oN if the 2-Door Expansion
module is at the beginning (Start Point) or at the
end (End Point) of the E-bus Network (see Figure
2). otherwise, place the EoL jumper oFF.
Figure 2: Setting the Jumpers
EOL Jumper
CT-V900
EOL = On
GND
+24V 12V MICRO CHECK www.postech.ca
LK1+ LOCK #1 OUT6
LK1- AC PRESENT R1/5V
LK2+ 24V READER +5V R1/0V
LOCK #2 12V EXPANSION PORT LOGIC +5V +12V SUPPLY
LK2- +24V SUPPLY R1/D0 High/Low Bias Jumpers
COM1 24V LOW BATT R1/D1
NO1 OUT1
NC1 RELAY RELAY #1 OUT2
COM2 1 R1/KA
NO2 RELAY RELAY #2 #3 READER #1 DATA R1/KB
NC2 2 R1/KC A+ = Low
R1/KD
+12V
+12V
GND +24V
Z1-2
COM R2/5V
Z3-4 R2/0V B- = Low
Z5-6 R2/D0
COM
Z7-8 DEF/RUN 9.6K/19.2K R2/D1
ADD 16 ADD 32 OUT3
+12V ADD 8 ADD 4 OUT4
GND ADD 2 R2/KA
ADD 1 READER #2 R2/KB
Z9-10 ON OFF DATA
COM R2/KC
Z11-12 R2/KD
Z13-14 +12V
COM +24V
Z15-16 A2+
HIGH LOW
A1+ A+ ON OFF E-BUS B2-
RING BATT TX RX GND
B1- 3V A+ TMP
GND LOW HIGH TMP
NETWORK EOL
HIGH LOW TX RX +
B- SERIAL PORT 1 2 3 4 B-
RESET SWITCH DB-9 E-BUS LOW HIGH S/N
CA-A470-A
Position Technology CA - A470 - A
AC
AC
D1NC LOCK#1 BAT+
COM BAT-
D1NO STATUS AC OK V+
D2NC COMM AUX OK V+
COM LOCK#2 JP120 CHECK BATT V-
D2NO 350mA/700mA BATT TRBL V-
SWITCH BACKUP OUT5
SW1 ADD 1 2 1 OUT6
SW2 SW3 ADD 2 ADD 4 0 0 1 0 NO CARD 2 CARDS
Z1 SW4 ADD 8 1 0 ALL CARDS A+ B-
COM SW5 BACKUP1 1 UNLOCK DOOR 1 EOL LOW
Z2 SW7 SW6 BACKUP2 PULSE 5&6 HIGH A+
Z3 SW8 N/D B-
COM GND
Z4 READER#2 DATA READER#1 DATA TAMPER
TAMPER
E-BUS TX RX
EOL Jumper
EOL = Off
High/Low Bias
Jumpers
A+ = High
B- = High
high/low Bias Jumpers
Place the A+ and B- jumpers on LoW only if the
2-Door Expansion module is at the beginning (Start
Point) of the E-bus Network. otherwise, place the
A+ and B- jumpers on hIGh (see Figure 2 and
Figure 3).
Figure 3: Setting the A+ and B- jumpers
During a Communication Failure:
350mA/700mA Battery Charging Jumper
the 350mA/700mA Jumper allows you to select
the charging current for the backup battery of the
2-Door Expansion module. charging the battery
at 350mA takes longer, but consumes less power.
charging the battery at 700mA takes less time, but
consumes more power.
Figure 4: Setting the 350mA/700mA jumper
programming in Centaur
using the centaur Access control Software,
program the inputs, outputs, readers, and keypads
connected to the 2-Door Expansion module. the
options are explained in the Centaur Access
Control Software Reference Manual. centaur
will identify the 2-Door Expansion module by its
address, DIP Switches 1 & 2, and will recognize
the devices as follows:
Doors
keypad/Reader 1
keypad/Reader 2
inputs
Z1
Z2
START POINT
Z3
Z4
END POINT outputs
out1
out2
out3
CA-A470-A CA-A470-A
out4
Position Technology CA - A470 - A Position Technology CA - A470 - A
AC AC
AC AC
D1NC LOCK#1 BAT+ D1NC LOCK#1 BAT+
COM BAT- COM BAT-
D1NO STATUS AC OK V+ D1NO STATUS AC OK V+
D2NC COMM AUX OK V+ D2NC COMM AUX OK V+
COM LOCK#2 JP120 CHECK BATT V- COM LOCK#2 JP120 CHECK BATT V- out5
D2NO 350mA/700mA BATT TRBL V- D2NO 350mA/700mA BATT TRBL V-
SWITCH BACKUP OUT5 SWITCH BACKUP OUT5
SW1 ADD 1 2 1 OUT6 SW1 ADD 1 2 1 OUT6
SW2 SW3 ADD 2 ADD 4 0 0 0 1 2 CARDS NO CARD SW3 SW2 ADD 2 ADD 4 0 0 0 1 2 CARDS NO CARD
Z1 SW4 ADD 8 1 0 ALL CARDS A+ B- Z1 SW4 ADD 8 1 0 ALL CARDS A+ B-
COM SW5 BACKUP1 1 1 UNLOCK DOOR EOL LOW COM SW5 BACKUP1 1 1 UNLOCK DOOR EOL LOW
Z2 SW6 SW7 PULSE 5&6 BACKUP2 HIGH A+ Z2 SW6 SW7 PULSE 5&6 BACKUP2 HIGH A+
Z3 SW8 N/D B- Z3 SW8 N/D B-
COM GND COM GND
Z4 READER#2 DATA READER#1 DATA TAMPER Z4 READER#2 DATA READER#1 DATA TAMPER out6
TAMPER TAMPER
E-BUS TX RX E-BUS TX RX
EOL Jumper EOL Jumper
EOL = Off EOL = On
High/Low Bias High/Low Bias
Jumpers Jumpers
A+ = High A+ = High
B- = High B- = High
Jumpers Jumpers
set to LOW set to HIGH
A+ B- A+ B-
LOW LOW
HIGH HIGH
Jumpers Jumpers
set as 350mA set as 700mA
Address 1 Address 2 Address 3
Door 3 Door 5 Door 7
Door 4 Door 6 Door 8
Input 17 Input 21 Input 25
Input 18 Input 22 Input 26
Input 19 Input 23 Input 27
Input 20 Input 24 Input 28
output 7 output 13 output 19
output 8 output 14 output 20
output 9 output 15 output 21
output 10 output 16 output 22
output 11 output 17 output 23
output 12 output 18 output 24
Doors cannot be defi ned as Door Type
Elevator (Door properties window, general
tab, Door Type: elevator) and the module
does not support Interlock Inputs (Door
properties window, inputs and outputs tab,
interlock input).
other modules in the system cannot activate
the 2-Door Expansion module's outputs.
the 2-Door Expansion module does not
support Zone Doubling (see Figure 6).