Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Microprop DC2
- Page 1 REVISION: 201301 DOC: 841615 ENGLISH ASSEMBLY INSTRUCTION MICROPROP DC2 DANFOSS...
- Page 2 CONTENT Safety regulations 1.1. General 1.2. Check list safety Symbols in the assembly instruction Control of delivery 3.1. 841517 Danfoss Assembly 4.1. Area A 4.1.1. Dismounting original joystick 4.1.2. Mounting adapter 4.1.3. Mounting adapter 4.1.4. Mounting joystick 4.1.5. Unloading wiring 4.1.6.
- Page 3 WARNING! Do no attempt to assemble, use or maintain the Microprop DC2 before you have read and understood all information regarding the tiltrotator, optional equipment and the machine. Be very aware of the safety information.
-
Page 4: Safety Regulations
SAFETY REGULATIONS 1. SAFETY REGULATIONS 1.1. GENERAL It is of utmost importance that you have read and understood all warnings before assembling and using the tiltrotator/rotator and supplied equipment. The warnings focus on potential risks and how these are avoided. If uncertain – contact your employer or supplier. - Page 5 SAFETY REGULATIONS WARNING! Risk of crushing by moving parts. WARNING! If uncertain of knowledge, equipment or working on safety details – contact your supplier or engcon Sweden AB. WARNING! Make sure that the labels are consistent to the machine function before putting the machine in use.
-
Page 6: Symbols In The Assembly Instruction
SYMBOLS IN THE ASSEMBLY INSTRUCTION 2. SYMBOLS IN THE ASSEMBLY INSTRUCTION Risk for injury to people and/or damage to property. WARNING! Read attached documentation for more information. No / incorrect measure Yes / correct measure 6 ENGLISH... -
Page 7: Control Of Delivery
CONTROL OF DELIVERY 3. CONTROL OF DELIVERY 3.1. 841517 DANFOSS Article Note Amount 841271 Joystick Danfoss left 841272 Joystick Danfoss right 841190 Cable for joystick 841871 Label Danfoss 841172 Label Danfoss 841161 Label symbols machine function – see-through 7 ENGLISH... -
Page 8: Assembly
ASSEMBLY 4. ASSEMBLY 8 ENGLISH... -
Page 9: Dismounting Original Joystick
ASSEMBLY 4.1. AREA A 4.1.1. Dismounting original joystick 4.1.2. Mounting adapter 9 ENGLISH... -
Page 10: Mounting Adapter
ASSEMBLY 4.1.3. Mounting adapter For L8 – see separate instruction. 4.1.4. Mounting joystick For L8 – see separate instruction. 10 ENGLISH... -
Page 11: Unloading Wiring
ASSEMBLY 4.1.5. Unloading wiring 4.1.6. Remount 11 ENGLISH... -
Page 12: Danfoss
ASSEMBLY 4.2. AREA B 4.2.1. 841517 Danfoss 12 ENGLISH... - Page 13 ASSEMBLY 4.3. AREA C Note 841105 841190 13 ENGLISH...
-
Page 14: Labels
LABELS 5. LABELS 5.1. TILTROTATOR FUNCTIONS Labels shall be plainly visible for the driver. Note Labels for joysticks 14 ENGLISH... -
Page 15: Machine Functions
LABELS 5.2. MACHINE FUNCTIONS Use the paper with machine function (841161) and place the symbols on the joystick labels so they correspond with the machine’s functions.. Note! Remember to update the machine user manual with the same information. 5.3. LABELS AT MORE THAN ONE USER SETTING If more than one user is activated in the system, the installer must mount another label per user. - Page 16 The machine original joysticks have been replaced in this machine. The servo controlled functions are still intact. See labels and the user manual of Microprop DC2 for more information. The installer is obliged to attach this information to the machine user manual.
Need help?
Do you have a question about the DC2 and is the answer not in the manual?
Questions and answers