Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Challenge Xtreme CDI224MN
Summary of Contents for Challenge Xtreme CDI224MN
- Page 1 24V CORDLESS HAMMER DRILL CDI224MN ORIGINAL INSTRUCTIONS...
-
Page 2: Safety Warnings
OrIgINaL INstructIONs gENEraL POWEr tOOL location is unavoidable, use a residual current device (rcD) protected supply. Use saFEtY WarNINgs of an RCD reduces the risk of electric shock. WarNINg: read all safety warnings and all instructions. Failure to follow the 3) PErsONaL saFEtY warnings and instructions may result in electric a) stay alert, watch what you are doing and... -
Page 3: Drill Safety Warnings
OrIgINaL INstructIONs dangerous and must be repaired. seek medical help. Liquid ejected from the c) Disconnect the plug from the power source battery may cause irritation or burns. and/or the battery pack from the power tool before making any adjustments, changing 6) sErvIcE accessories, or storing power tools. - Page 4 OrIgINaL INstructIONs sYMBOLs the cell, battery and equipment and ensure correct use. i) Do not use any cell or battery pack which is To reduce the risk of injury, user must not designed for use with the equipment. read instruction manual j) Do not mix cells of different manufacture, capacity, size or type within a device.
- Page 5 OrIgINaL INstructIONs HELPLINE NO 08448012949...
- Page 6 OrIgINaL INstructIONs cOMPONENt LIst 1. Keyless chuck 2. Torque adjustment ring 3. Two-speed gear control 4. Forward/Reverse rotation control 5. On/Off switch 6. Soft grip handle 7. Sight light 8. Battery pack release button 9. Battery pack * 10. Auxiliary handle * Not all the accessories illustrated or described are included in standard delivery.
- Page 7 OrIgINaL INstructIONs tEcHNIcaL Data Type cDI224MN(cDI-designation of machinery, representative of Battery-powered Impact Drill) Charger voltage 230-240v~50Hz voltage No load speed 0-400/0-1200/min Impact rate 0-5200/0-15600/min Max. torque 30N.m Number of clutch positions 20+1+1 Chuck capacity 13mm Max. drilling capacity 10mm steel...
- Page 8 OrIgINaL INstructIONs Avoid using tools in temperatures of 10 C or less. Plan your work schedule to spread any high vibration tool use across a number of days. HELPLINE NO 08448012949...
- Page 9 OrIgINaL INstructIONs rEcHargINg BattErIEs Insert the battery pack into the Charger base (d). The green light (c) will on and the red light (b) will NOtE: Before using the tool, read the remain on. instruction book carefully. A discharged battery at normal ambient temperature will take approximately 3-5 hours to INtENDED usE reach full charge.
- Page 10 Fig. D OrIgINaL INstructIONs Fig. A1 Fig. A2 higher speed and torque with increased trigger pressure. Speed is controlled by the amount of switch trigger depression. WarNINg: Do not operate for long periods at low speed because excess heat will be produced internally. Fig.
- Page 11 Fig. F Fig. H OrIgINaL INstructIONs Fig. G Fig. F bit holder Fig. I Fig. G Fig. I 7. FIttINg aND rEMOvINg scrEWDrIvEr BIts (see Fig. H) bit holder To use any short screwdriver bit supplied, insert the bit into the bit holder and push the holder into Fig.
- Page 12 OrIgINaL INstructIONs The sight light (8) allows you to keep a clear view an edge of the material, a pilot hole will also under less illuminated circumstances. To turn on help to prevent splitting of the wood. the light simply press the on/off switch. When you 2.
- Page 13 OrIgINaL INstructIONs batteries during the charging process. 8. the charger will get warm during charging This is normal. it is a result of the stepping down of the main supply. HELPLINE NO 08448012949...
-
Page 14: Environmental Protection
OrIgINaL INstructIONs ENvIrONMENtaL PrOtEctION Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. If faults can not be remedied, contact the Helpline on 08448012949 guaraNtEE This product is selected for DOMESTIC USE ONLY and not for business use.