Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for CRU Ditto Foensic FieldStation
- Page 2 Depending on which configuration and accessories you purchased, the Destination Outputs package may include fewer items than what are listed here. Please contact CRU if any items are missing or damaged: Ditto Unit eSATA connections RJ45 Gigabit Ethernet connection...
-
Page 3: Setup
• Note that Ditto is configured to use DHCP for IP assignment. If you need to change to a Static IP, check When you add or remove a drive or enclosure from Ditto, CRU with the network administrator and see section 3.3.2 of recommends that you switch the power off to Ditto to avoid this manual. -
Page 4: Home Screen
4.1.3 Clone and Image Source Disk: This action NetView Scan feature. simultaneously performs a clone to one destination disk and perform an image to the second destination disk. Two destination disks are required for this action. CRU Mark Page 4 10.25.12 PMS 711 2 cyan... - Page 5 CRU Mark 10.25.12 PMS 711 2 cyan...
-
Page 6: Settings
• This will scan hosts 10.10.10.1, 10.10.10.2 and hosts 10.10.10.50 through 10.10.10.100. Remember that the “Reset” button may be used to reset the IP Scan Range back to its default values. CRU Mark Page 6 10.25.12 PMS 711 2 cyan... - Page 7 Examples: 1. Range: 1-1000 • This will scan TCP ports 1 through 1000 2. List: 22,80 • This will only scan TCP ports 22 (SSH) and 80 (HTTP) CRU Mark Page 7 10.25.12 PMS 711 2 cyan...
-
Page 8: Disks
Ditto on your computers via iSCSI. This can be very useful if you wish to scan, image, or otherwise use the disk with 3rd party software. Using either the source or destination network port works equally well. CRU Mark Page 8 10.25.12 PMS 711 2 cyan... - Page 9 CRU Mark 10.25.12 PMS 711 2 cyan...
- Page 10 Click the “Remove” button to remove that share. Enter the Server name or the path to the NFS or Samba Share and select “Show Shares.” This will bring up the CRU Mark Page 10 10.25.12 PMS 711...
-
Page 11: Configure Screen
Ditto allows you to select from various erase modes. See the following table for the available erase modes. Find out more about each mode by clicking the “info” button next to the erase mode selection. CRU Mark Page 11 10.25.12 PMS 711... - Page 12 • Source Drive Unique ID – ID or serial number of the drive attached to the Source eSATA port. The Time Stamp field is shown as grayed out as it is always begins the directory name. CRU Mark Page 12 10.25.12 PMS 711...
-
Page 13: Admin
6. Admin The Admin screen allows the administrator to manage user accounts and assign permission levels for each user. CRU recommends investigator accounts be set up for best practices. Permission levels on the web browser interface are displayed as FULL, AUTH, or a hyphen. FULL is full access without a password. -
Page 14: Utilities
9.1 Status Screen new features or increase compatibility. The Status screen is the default screen. It shows the Firmware upgrades will be made available on CRU’s site progress of any current processes or reports the status as www.cru-inc.com/products/Ditto.php. A link will be idle. -
Page 15: Settings
Time left: 57.2Min The Disk Info screen shows all available drives attached to < Abort either the source or destination ports. Each port is shown only if a drive is connected there. CRU Mark Page 15 10.25.12 PMS 711 2 cyan... -
Page 16: Factory Reset
< Cancel Continue > Press ENTER to continue or BACK to cancel. You may also use the web browser interface to do a factory reset. See section 8.1 for more information. CRU Mark Page 16 10.25.12 PMS 711 2 cyan... -
Page 17: Technical Specifications
Weight: incidental damages arising in any way out of the sale of, use of, or inability to use any CRU product or service, even if CRU has been advised of the possibility of such damages. In no case shall CRU’s liability exceed the actual money paid for the products at issue.
Need help?
Do you have a question about the Ditto Foensic FieldStation and is the answer not in the manual?
Questions and answers