Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Questtel 1B-SDI-PTGM2-HD
-
Page 1: User Manual
3G-HD/SD SDI Monitor User Manual... - Page 2 Safety and Notice The 1B-SDI-PTGM2 3G-HD/SD SDI Monitor has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments,1B-SDI- PTGM2 should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.
- Page 3 Introduction The 1B-SDI-PTGM2 3G-HD/SD SDI Monitor offers the highest compatibility among SDI, including 3G/HD/ SD formats. This device also supports composite (NTSC/PAL) input through the same input. With the embedded advanced de-interlacer, interlaced video inputs, such as SD-SDI or composite, can be further improved. For SDI, 1B-SDI-PTGM2 can display support up to 8 channel audio bars to indicate the embedded digital audio channel in SDI stream and make 1B-SDI-PTGM2 a perfect mini monitor to watch closely on SDI signal quality.
- Page 4 Specifications & Package Contents Model Name 1B-SDI-PTGM2 Technical LCD size & resolution 5.7” & 640x480 LCD color depth 18 bit RGB Composite bandwidth 13.5MHz Audio support Up to 8 CH decoding and audio bar display SDI Support SD/HD/3G Input 1 x SDI [CVBS] Output 2x SDI [Loopout] Audio FS support...
-
Page 5: Ir Remote Control
IR Remote Control Idle Source: No use in this model Info: Display input type and time Auto: No use in this model C.C.: No use in this model HDMI: No use in this model Aspect: Aspect ratio change Freeze Video Sleep ON Menu Control Buttons... -
Page 6: Panel Descriptions
Panel Descriptions Front Panel 1. DIO: Reserved. 2. Dip Switch: Mode setting 3. RS-232: Serial control Rear Panel 4. SDI BNC loop-out connectors: SDI loop outs 5. SDI BNC input connector: Input SDI/CVBS 6. Power LED: Indicate power up and signal lock 7. -
Page 7: Hardware Installation
Top Panel Buttons 9. IR: Remote control 10. Menu: OSD Menu 11. Down/Left: OSD up or left operations 12. Up/Right: OSD down or right operations 13. Enter/Mode: OSD selection or zoom/pan 14. INC+: Zoom in or move the center of zoomed video to left or up 15. -
Page 8: Default Setting
Default Setting 1. Power up the 1B-SDI-PTGM2. 2. To reset 1B-SDI-PTGM2 back to the factory default values, pull up-and-down the DIP switch 1&2 from OFF to ON to complete the process. You NEED to pull back the DIP switch back to OFF in order to get 1B-SDI- PTGM2 work normally. - Page 9 Window Messages The connection is not correct. Please check: Power Cable Baud Rate The whole firmware update procedure fails. Please check Power Cable Baud Rate The firmware update procedure requires a power cycle. Please turn off the device, wait for a couple of seconds, and power on the device.
- Page 10 Appendix – Supported Resolution [SDI-IN] Socket Supported Mode Resolution (SDTV) 625i 625i @50Hz (SDTV) 525i 525i @59.94Hz (HDTV) 720p 1280x720 @50Hz (HDTV) 720p 1280x720 @59.94Hz (HDTV) 720p 1280x720 @60Hz (HDTV) 1080i 1920x540 @50Hz (HDTV) 1080i 1920x540@59.94Hz (HDTV) 1080i 1920x540 @60Hz (HDTV) 1080p 1920x1080 @25Hz (HDTV) 1080p...
- Page 11 Appendix – SDI Dialog Dialog 1 –SDI Information □□: □□: □□ [System timer] EDH error number and error rate [SD only] CRC error number and error rate SDI input total width and height SDI input active width and height SDI input format Dialog 2 - SDI SYNC information Dialog 3 - SDI Video Information EDH Status:...
-
Page 12: Safety Instructions
If the video product is dropped or the cabinet is damaged. When the video product exhibits a distinct change in performance, this indicates a need for service. www.questtel.com sales@questtel.com...