SAB SABVISION NVR32 Quick Start Manual
  1. Manuals
  2. Brands
  3. SAB Manuals
  4. Network Hardware
  5. SABVISION NVR32
  6. Quick start manual

SAB SABVISION NVR32 Quick Start Manual

Sabvision nvr series
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Network Video Recorder
Quick Start Guide

Advertisement

Table of Contents
loading

Summary of Contents for SAB SABVISION NVR32

  • Page 1 Network Video Recorder Quick Start Guide...
  • Page 2 Chapter 2 Installation and Connections ..................... 11 2.1 NVR Installation ..........................11 2.2 Hard Disk Installation ......................... 11 2.2.1 SABVISION NVR16 & SABVISION NVR32 ................. 11 2.3 Connections ............................14 2.3.1 Alarm Input Wiring ......................... 14 2.3.2 Alarm Output Wiring ......................14 2.3.3 Using Alarm Connectors ......................
  • Page 3 Network Video Recorder Quick Start Guide Quick Start Guide About this Manual This Manual is applicable to Network Video Recorder (NVR). The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.

  • Page 4: Regulatory Information

    Network Video Recorder Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
  • Page 5 This manual is applicable to the models listed in the following table. Series Models SABVISION NVR16 SABVISION NVR SABVISION NVR32 Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Provides additional information to emphasize or supplement important points of the main text.

  • Page 6: Safety Instructions

    Network Video Recorder Quick Start Guide Safety Instructions  Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.  In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region.

  • Page 7: Chapter1 Panels Description

    Network Video Recorder Quick Start Guide Chapter1 Panels Description 1.1 Front Panel 1.1.1 SABVISION NVR32 Figure 1-1 SABVISION NVR32...
  • Page 8 Network Video Recorder Quick Start Guide Table 1-1 Panel Description No. Name Function Description POWER Turns green when NVR is powered up. Status Blinks red when HDD is reading/writing. Indicators Blinks green when network connection is functioning Tx/Rx normally. The Enter button is used to confirm selection in menu mode;...

  • Page 9: Rear Panel

    Universal Serial Bus (USB) port for additional devices such as USB Interface USB mouse and USB Hard Disk Drive (HDD). 1.2 Rear Panel 1.2.1 SABVISION NVR32 Figure 1-3 SABVISION NVR32 Table 1-3 Panel Description Name Description LAN Interface 1 network interface provided.

  • Page 10: Sabvision Nvr16

    Network Video Recorder Quick Start Guide LINE IN RCA connector for audio input. HDMI HDMI video output connector. USB 3.0 interface Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). RS-232 Interface Connector for RS-232 devices.
  • Page 11 DS-7600NI-I4/P and DS-7600NI-K4/P. Power Switch Switch for turning on/off the device. Network Interfaces with PoE function Network interfaces for the cameras and to provide power over Ethernet. (supported DS-7600NI-I2/P) SABVISION NVR16 and SABVISION NVR32 provide 16 network Interfaces with PoE function.

  • Page 12: Nvr Installation

    Network Video Recorder Quick Start Guide Chapter 2 Installation and Connections 2.1 NVR Installation During installation of the NVR:  Use brackets for rack mounting.  Ensure ample room for audio and video cables.  When routing cables, ensure that the bend radius of the cables are no less than five times than its diameter.
  • Page 13 Network Video Recorder Quick Start Guide Figure 2-1 Remove Cover Step 2 Connect one end of the data cable to the motherboard of NVR and the other end to the HDD. Figure 2-2 Connect Data Cable Step 3 Connect the power cable to the HDD. Figure 2-3 Connect Power Cable Step 4 Place the HDD on the bottom of the device and then fasten the screws on the bottom to fix the HDD.
  • Page 14 Network Video Recorder Quick Start Guide Figure 2-4 Fix Hard Disk...

  • Page 15: Connections

    Network Video Recorder Quick Start Guide 2.3 Connections 2.3.1 Alarm Input Wiring The alarm input is an open/closed relay. To connect the alarm input to the device, use the following diagram. If the alarm input is not an open/close relay, please connect an external relay between the alarm input and the device.

  • Page 16: Controller Connection

    Network Video Recorder Quick Start Guide If you connect an AC load to the alarm output 3 of the NVR, then you must remove the JP 3 jumper. 2.3.3 Using Alarm Connectors To connect alarm devices to the NVR: Step 1 Disconnect pluggable block from the ALARM IN /ALARM OUT terminal block. Step 2 Unfasten stop screws from the pluggable block, insert signal cables into slots and fasten stop screws.

  • Page 17: Hdd Storage Calculation Chart

    Network Video Recorder Quick Start Guide 2.4 HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate. Bit Rate Storage Used 128K 160K 192K 224K...

  • Page 18: Menu Structure

    Network Video Recorder Quick Start Guide Chapter 3 Menu Operation 3.1 Menu Structure Refer to the following figure for the menu structure: Menu Playback Maintenance Shutdown Export VCA Search Record Camera Configuration Manual Behavior Normal Normal Schedule Camera General System Info Logout Record General...

  • Page 19: Activating Your Device

    Network Video Recorder Quick Start Guide Step 2 Press the POWER button on the front panel. The Power LED should turn blue. The unit will begin to start. After the device starts up, the wizard will guide you through the initial settings, including modifying password, date and time settings, network settings, HDD initializing, and recording.

  • Page 20: Using The Unlock Pattern For Login

    Network Video Recorder Quick Start Guide STRONG PASSWORD RECOMMENDED–We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product.

  • Page 21: User Login

    Network Video Recorder Quick Start Guide  Connect at least 4 dots to draw the pattern.  Each dot can be connected for once only. Step 2 Draw the same pattern again to confirm it. When the two patterns match, the pattern is configured successfully.

  • Page 22: User Logout

    Network Video Recorder Quick Start Guide In the Login dialog box, if you enter the wrong password 7 times, the current user account will be locked for 60 seconds. 3.5.2 User Logout Purpose: After logging out, the monitor turns to the live view mode and if you want to perform any operations, you need to enter user name and password log in again.

  • Page 23: Network Settings

    Network Video Recorder Quick Start Guide Figure 3-9 Wizard 3.7 Network Settings Purpose: Network settings must be properly configured before you operate NVR over network. Step 1 Enter the Network Settings interface. Menu > Configuration > Network Figure 3-10 Network Settings Step 2 Select the General tab.

  • Page 24: Adding Ip Cameras

    Network Video Recorder Quick Start Guide Step 4 If the DHCP server is available, you can check the checkbox of DHCP to automatically obtain an IP address and other network settings from that server. Step 5 After having configured the general settings, click the Apply button to save the settings. 3.8 Adding IP Cameras Purpose: Before you can get live video or record the video files, you should add the network cameras to the connection list of the device.

  • Page 25: Recording Settings

    Network Video Recorder Quick Start Guide Live View Icons In the live view mode, there are icons at the upper-right corner of the screen for each channel, showing the status of the record and alarm in the channel for quick reference. Alarm (video loss, tampering, motion detection, VCA or sensor alarm) Record (manual record, continuous record, motion detection, VCA or alarm triggered record) Alarm and Record...

  • Page 26: Playback

    Network Video Recorder Quick Start Guide 3.11 Playback The recorded video files on the hard disk can be played back in the following modes: instant playback, all-day playback for the specified channel, and playback by normal/event/smart/tag/sub-periods/external file search. Step 1 Enter playback interface. Click Menu>Playback or from the right-click menu.

  • Page 27: Chapter 4 Accessing By Web Browser

    Network Video Recorder Quick Start Guide Chapter 4 Accessing by Web Browser You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection.
  • Page 28 Network Video Recorder Quick Start Guide  If the device is already activated, enter the user name and password in the login interface, and click the Login button. Figure 4-2 Login Step 3 Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in.
  • Page 29 Network Video Recorder Quick Start Guide...

This manual is also suitable for:

Sabvision nvr16

Table of Contents