Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for DTX RA-S01
- Page 1 WIFI/GPRS+GSM Smart Home Alarm System Key Features: WiFi network, internet push without charge Zone names can be revised by users IP camera APP integrated in the alarm APP Work with smart socket, support scene/linkage settings for home automation...
- Page 3 Contents Preface Key features Technical information Front side panel view Backside panel view Initialization How to use APP How to connect WiFi for host Add equipment Introduction of APP main interface Sensor learning How to learn RFID keypad Zone attribution settings Edit sensor attribution Delete sensors Host settings...
- Page 4 Hotspot setup Unbind equipment Switch equipment Authorization Logout Call up Answer alarm call Remote phone call control Remote SMS control Maintenance...
-
Page 5: Preface
Preface Thanks for choosing our GSM+Wi-Fi/GPRS/SMS home alarm system. GSM+Wi-Fi/GPRS/SMS home alarm system has implanted the most advanced and popular Wi-Fi technology into traditional GSM alarm system technology, with ver y simple wireless set up. It’s ver y convenient for users to set up the alarm system via APP. Compared with traditional SMS APP, Wi-Fi APP is with much more simple and quicker operation. -
Page 6: Key Features
Key features 1.WIFI/GPRS/SMS + GSM home alarm system When there is no WIFI, the host will work with GPRS network. If there is neither WiFi nor GPRS network, then the alarm host will send alarm SMS and make alarm call. 9.Information push promptly when AC power failure/recovered or detectors in low voltage... -
Page 7: Technical Information
Technical information Power supply: AC=100 ~ 230V 50Hz/60Hz Working voltage: DC5V 2A Static current: < 200mA (when not under charging status) Alarm current: < 300mA Backup Battery: 3.7V 1050mah Standby time: 7 hours Charging time: 3.5 hours GSM frequency: 850/900/1800/1900MHz GSM Transmission power: 2W(850MHz/900MHz);1W(1800MHz/1900MHz) Wifi transmission Power: 1W Receiving and emitting frequency: 433MHz (868MHz optional) -
Page 8: Front Side Panel View
Front side panel view Display Home Arm Away Arm GSM indicator WIFI indicator Display When host receive message, the display button will flash slowly, users can press the display button to listen to the message. When someone make call to the host, it will ring and the display button flash fast, users can press the display button to answer the call. - Page 9 Home Arm GSM signal: If the GSM signal do not flash, that means GSM have not initiated yet. If the GSM signal flash once, that means GSM have initiated. If the GSM signal flash twice, that means there is SIM card. If the GSM signal flash thrice, that means the host can make call .
-
Page 10: Backside Panel View
Backside panel view Sim card Slot After switch on the host, short press the K2 button to close host hotspot. After switch on the host, long press the K2 button to set the host to default. After switch on the host, short press the K1 button to open the host hotspot. Initialization First install SIM card and power the alarm host with adapter, then switch on the alarm host.About 3 seconds later, the panel will make a long beep, then... -
Page 11: How To Connect Wifi For Host
How to connect WiFi for host Step one: power the alarm host with adapter. Step two: go to the WLAN interface of smartphone, find the host hotspot whose name begin with IWTAC_. Note: if you can not find that hotspot, please short press K1 button at the back side of host to restart WiFi for host. -
Page 12: Add Equipment
Add equipment Log in APP application, click button,click button. Then choose sub-menu “add equipment”, users now can scan the QR code of panel. The first one who scan the QR code of host will become that host administrator. Note: before users add equipment, please confirm the smartphone is connected with workable WiFi/GPRS network but not the alarm host hotspot. -
Page 13: Sensor Learning
Voice message : keep pressing the button and start to record the message, release the button to end the recording. (Maximum 20s voice message can be recorded.) About 1 minute later, the display button on alarm host will flash slowly, families members can press the display button to listen to the voice message. -
Page 14: How To Learn Rfid Keypad
How to learn RFID keypad: Log in APP application, slide the screen to Sensor List interface. Step one: Click the “Add” button, the APP will go to New Sensor interface. Step two: choose Sensor Type as “RFID”, then click the “Add” button. The host will say “start learning, please trigger detector ”. -
Page 15: Zone Attribution Settings
Zone attribution settings: Defense Line: 24H defense line: it means 24 hours protection, the alarm sensors in this line will trigger the alarm system whenever in arm status or disarm status, usually panic button, smoke detector,gas leakage sensor, etc should be learned to 24H defense line. -
Page 16: Edit Sensor Attribution
Independent Zone: Every zone can be set to be independent zone, which only can be disarmed by APP, but can't be disarmed by remote controllers. The feature is suitable for important room or private room. Sensor Type: the name of sensor Type: the type of sensor Note: for smart door sensor, please choose Smart door sensor. - Page 17 Delay Set:It includes arm delay setting and alarm delay setting. 1.Arm Delay: Arm time delay setting is that the host will not be armed until delayed time arrives. Therefore, when touch “ away arm” button on alarm host,users will have time to deviate from house. 2.Alarm Delay: First user should active “alarm delay”...
-
Page 18: Wireless Relay Outputs Learning
Wireless relay outputs learning Firstly, Connect wireless relay outputs with power adapter. To reset the relay, user can long press its learning button about 6 seconds until the LED indicator lamp lights on again. Secondly, log in APP application, click the “Automation” button to enter the device List interface. - Page 19 Attention: When you plug the Jumper between the 1, 2 pins, four bulbs will simultaneously be opened and closed, or opened /closed several of them; when Jumper between the 2, 3 pins, you can only turn on one bulb once, for example, if you have already opened the '1' bulb, when open the “2”...
-
Page 20: Rf Socket
RF Socket Firstly, log in APP application, click the “Automation” button to enter the Device List interface. Then click the Add button to go to New Device adding interface. Secondly, input device name, choose Device Type “ Socket ” and choose Sub Type “... -
Page 21: Control Device
Fourthly, users can click Yes button of the APP notice “Registering, does the device And the host will say “ have the right action ?” The APP will refresh the device list. learning success” . Control devices: Click that device(siren/relay output/smart socket), APP will turn to device control interface. -
Page 22: Scene
Scene Scene is a serial of devices actions. For example, users can set a return home scene. When users Execute the scene, the living room light and the air-condition will be turned on. How to add a scene Firstly, Log in APP application, click the “Automation” button to enter the Device List interface. -
Page 23: Delete Scenes
Delete scenes Long press scene , APP tips below, uses can click [confirm] to delete that scene, click [delete all] to delete all scenes. Linkage What is linkage: a trigger which can be detector or time make one device or one scene act. - Page 24 Firstly edit new linkage name. Trigger Type can be sensor or time. Trigger action can be close or open. Linkage type can be device or scene. Linkage Action can be open or close Delay Action for delay : if the linked one is device, users can also set a delayed action for that device.
-
Page 25: Four Types Linkage
Four types linkage Sensor linked to device Sensor linked to scene Time linked to scene Time linked to device... -
Page 26: Delete Linkage
Enable and Disable linkage: Delete linkages Long press linkage , APP tips below, uses canclick [confirm] to delete that linkage, click [delete all] to delete all linkages. History Click the [history] button, the latest 100 alarm and operation records can be traced. -
Page 27: Ip Camera Monitor Function
IP camera monitor function To better experience the convenience of this product, before using this product, please download the Phone App. IOS users can go to the APP Store to search ” yoosee ” and download IP camera App. Android users can go to the Google Play to search “ yoosee ”... - Page 28 Thirdly: Power on the IP camera and then connect IP camera with network cable. Then the IP camera can connect with network. Refresh “Device list” , then users can see that IP camera would be “online”. Fourthly, Click that IP camera device, appear “playback”, “setting” and “edit” buttons.
-
Page 29: Hotspot Setup
Hotspot setup : the alarm host hotspot password (default:123456789), users can edit the password. Enable : users can enable/disable the host hotspot Enable WiFi Net : users can enable/disable WiFi network of alarm hosts. Enable GSM Net : users can enable/disable GSM network of alarm host. About APN Install SIM card and then turn on the alarm host, connect WiFi for host, the host will configure APN automatically and the APP will shows the APN name. -
Page 30: Unbind Equipment
Unbind equipment Log in APP application, click button. Then choose sub-menu “unbind equipment”, user can touch “Unbind” to unbind the present equipment. Switch equipment Log in APP application, click button. Then choose sub-menu “switch equipment”, popping the below picture, touch each device to switch equipment. -
Page 31: Authorization
Authorization The APP administrator can give authorization to other users. The other users need to download APP and sign up firstly and get the right to be authorized, then the administrator can successfully give authorization. Operation as below: log in APP application, click button. -
Page 32: Answer Alarm Call
Call up It means alarm host can be used as a hand-free phone: when someone make call to alarm host, the host will ring and the person beside the alarm host can touch the “display” button to answer the call. After finish conversation touch the “display”... -
Page 33: Remote Sms Control
Press [1]: the host stops alarming to Away Arm; it stops calling users. Press [2]: the host stops alarming to Home Arm; it stops calling users. Press [3]: the host stops alarming to Disarm; it stops calling users. Press [4]: the siren will stop ring and the host will start monitor. Press [5]: start talkback. -
Page 34: Maintenance
Maintenance Alarm system need regular care and maintenance and detection to ensure they work stably and securely. Normally the host needs a thorough inspection every 3 months and the detectors need to be checked once a month. Whether the host normally dials up the telephone numbers. Whether the host can receive detector signal and whether its backup battery works. - Page 36 RoHS...
Need help?
Do you have a question about the RA-S01 and is the answer not in the manual?
Questions and answers