Download Print this page

Fujian Quanzhou Beifeng Telecom Systems BF620001 User Manual

Two-way radio

Advertisement

Quick Links

User Safety, Training, and General Information
READ THIS IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION BEFORE
USING YOUR BFDX FOR TABLE TWO-WAY RADIO.
Compliance with RF Energy Exposure Standards
The two-way radio is designed and tested to comply with a number of national and international
standards and guidelines (listed below) regarding human exposure to radio frequency
electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for
occupational/controlled RF exposure environment at duty cycles of up to 50% talk-50% listen and
should be used for occupational use only. In terms of measuring RF energy for compliance with the
FCC exposure guidelines, your radio radiates measurable RF energy only while it is transmitting
(during talking), not when it is receiving (listening) or in standby mode.
The approved batteries supplied with this radio are rated for a 5-5-90 duty cycle (5% talk-5%
Note:
listen-90% standby), even though this radio complies with the FCC occupational RF exposure
limits at duty cycles of up to 50% talk.
Complies with the following of RF energy exposure standards and guidelines:
United States Federal Communications Commission, Code of Federal Regulations; 47CFR part
2 sub-part J
American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers
(IEEE) C95. 1-1992
Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1999 Edition International
Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998
Operational Instructions
To ensure optimal performance and compliance with the occupational/controlled environment RF
energy exposure limits in the above standards and guidelines, users should transmit no more than
50% of the time and always adhere to the following procedures:
Hand-held radio operation
Hold the radio in a vertical position with the microphone 5 cm away from the lips and let
the antenna farther away from your head.
Notices to the User
•Government law prohibits the operation of unlicensed radio transmitters within the territories
under government control.
•Illegal operation is punishable by fine or imprisonment or both.
•Refer service to qualified technicians only.
WARNING: It is important that the operator is aware of and understand hazards common to the
operation of any transceiver. Explosive environment(such as gases, dust, fumes, etc). Turn off your
transceiver while talking on fuel, or while parked in gasoline service stations.
If you require this machine to be developed or some changed, pleased connect with BFDX or your
BFDX dealer.
THE USER'S MANUAL

Advertisement

loading
Need help?

Need help?

Do you have a question about the BF620001 and is the answer not in the manual?

Questions and answers

Summary of Contents for Fujian Quanzhou Beifeng Telecom Systems BF620001

  • Page 1 THE USER’S MANUAL User Safety, Training, and General Information READ THIS IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION BEFORE USING YOUR BFDX FOR TABLE TWO-WAY RADIO. Compliance with RF Energy Exposure Standards The two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy.
  • Page 2: Fcc Caution

    Do not place the radio in excessively dusty, humid areas, nor on unstable surfaces. CE Caution: Fujian Quanzhou Beifeng Telecom Systems Co., Ltd. Hereby, declares that this Tow-way radio is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
  • Page 3 Training Guidelines 1.Only qualified technicians are allowed to maintain this product. 2.To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any place where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy.
  • Page 4 CONTENTS Unpacking and checking accessories ------------------------------- Supplied accessories-------------------------------------------------- Preparation--------------------------------------------------------------- Use Li-ion battery----------------------------------------------------- The characteristic of Li-ion battery--------------------------------- Charging for the Li-ion battery pack-------------------------------- Install & take off the battery pack----------------------------------- Install the antenna------------------------------------------------------ Getting acquainted------------------------------------------------------ LCD display------------------------------------------------------------ Operating basics---------------------------------------------------------- Switching power on/off------------------------------------------------ Adjusting the volume-------------------------------------------------- Choose channel--------------------------------------------------------- Adjusting the squelch--------------------------------------------------...
  • Page 5 Choice DQT--------------------------------------------------------------- Setup for the provisional different Tx/Rx frequency----------------- Beat setup on the frequency mode-------------------------------------- Step frequency setup on the frequency mode-------------------------- QT codes table---------------------------------------------------------------- DQT codes table-------------------------------------------------------------- Technical specification-------------------------------------------------------...
  • Page 6 Unpacking and Checking Note: The following explain for unpacking is aim to the dealer, promised service institution or factory. Please carefully unpack the transceiver, we recommend you identify the items listed in the following table. If any items is missing or have been damaged, please immediately contact your dealer.
  • Page 7 Preparation: Alarm: Please don’t charging too long for the battery pack If the charging not finished in the stated time, please stop it, the battery pack may over heat and smoking blast or build a fire. Please don’t put the battery pack into the microwave lamp or high voltage container The battery pack may over heat and smoking blast or build a fire.
  • Page 8 battery pack may aging faster when store in heat environment. Please don’t leave the battery pack in vehicle or beside the heater. If the using time of the battery pack become short, even if the full capacity, please change it. Go on charging and discharge for the battery pack, it may result in the electrolyte leak.
  • Page 9 Getting acquainted ○ Power on/off and volume adjuster Turn the knob clockwise then the power will turn on, it can adjust the volume after turn on. Turn the knob counter-clockwise, it will turn off the power. ○ LED light When transmit it turn red, receive it turn green. The red light glitter when in low battery.
  • Page 10: Adjusting The Volume

    Display Icon Description - Current channel power output Tx lower than Rx + Current channel power output Rx lower than Tx When the choosing channel included in scanning list it display, deleted channels aren’t display this icon Current channel on low power output transmitting Display frequency, channel number, menu setup or other function According to the function you chose, display the number...
  • Page 11 to choose the high channel number, counterclockwise to choose the low channel number. The selected channel number display on the screen Adjusting the squelch The function of squelch can let the speaker no voice when no signal input, when open the squelch, you will hear the background voice from the speaker, contrarily you can not hear.
  • Page 12 The local dealer may programming the transceiver with the QT and DQT, when you choose these channels, you can just hear the same code in the same channel, any others will not receive. Display mode Press the CH2F can switch from frequency mode to channel mode. Scanning Channel display mode Scanning is useful function, it used to monitor the channel’s signal of the...
  • Page 13: Auxiliary Functions

    on the current frequency, it can receive and transmit. In the any time of scanning, if you press the PTT button the transceiver will stop scanning, the transceiver return to the latest channel and transmit. If always receive the signal in the period of scanning, it will return to the start channel and transmit.
  • Page 14 You can choose keypad voice close, open and Chinese voice. Choose keypad voice: 1. Hold on the FUNC button for one second, then press LOW button 2. Rotate the channel selector to choose the voice you need, choose close display “OF”, choose open display “1”, choose Chinese voice display “2”.
  • Page 15 or change another battery pack. Monitor You can use the MONI button to receive the very low signal, and it also can adjust the volume when the channel don’t have signal, hold on the MONI button to monitor the background voice, undo to return to the normal operation.
  • Page 16 Setup for the provisional different Tx/Rx frequency This function just can use on the frequency display mode 1. Press FUNC button then SCAN button, the LCD display “±” 2. Use the keypad and channel selector choose the Tx frequency you need, press the FUNC button, the selected Tx frequency store into the current channel.
  • Page 17 Frequency Frequency Frequency Frequency 67.0 94.8 131.8 186.2 69.3 97.4 136.5 192.8 71.9 100.0 141.3 203.5 74.4 103.5 146.2 210.7 77.0 107.2 151.4 218.1 79.7 110.9 156.7 225.7 82.5 114.8 162.2 233.6 85.4 118.8 167.9 241.8 88.5 123.0 173.8 250.3 91.5 127.3 179.9...
  • Page 18 Technical Specifications Low frequency range 406.125-407.350MHz Frequency range Mid frequency range from 440.125-441.350MHz High frequency range from 468.125-469.400MHz Channels Channel space 25KHz ℃ ℃ Operating temperature range to +60 Power supply 7.2V DC (±20%) Volume 51(L)×28(W) ×90(H)mm Weight 183g(including the battery pack) Transmitter Power output 3W/1W (Conducted power)