Advertisement
Table of Contents
- 1 User Manual
- 2 Important Information
- 3 Warranty
- 4 Main Functions
- 5 Temperature Sensor Drawing
- 6 Setting the Master User
- 7 Controlling the Power (Output) Manually
- 8 Deleting an Additional User
- 9 Controlling the Power (Output) by Time Delay – Power on
- 10 Setting the Temperature Range Parameters
- 11 Controlling the Power (Output) by Temperature Range – off
- 12 Signal Strength
- Download this manual
See also:
User Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Tekview POWERTXT
Summary of Contents for Tekview POWERTXT
-
Page 1: User Manual
Tekview Limited Unit 8 George Holmes Business Centre George Holmes Way Swadlincote Derbyshire DE11 9DF United Kingdom +44 203 176 3094 Please note calls and emails are answered in English (Time Zone: GMT) info@tekview-solutions.com www.tekview-solutions.com © Tekview Limited 2015 USER MANUAL... - Page 2 Important Information ..............04 Controlling the Power (Output) by Time/Day & Delay Safety Recommendations..............04 4.1. Setting the Time/Day Parameters ..........16 Disclaimer Notice ................04 4.2. Controlling the Power (Output) by Time/Day – ON ....18 Warranty ....................07 4.3. Controlling the Power (Output) by Time/Day – OFF ....18 EstateView Software ..............07 ..18 4.4.
-
Page 3: Important Information
• Powertxt® will reply to each SMS command that is sent to it purpose. Every effort has been taken to ensure the accuracy of (network dependent) (except when changing the master... -
Page 4: Warranty
Warning – Powertxt® is not designed for use in, and should not conditions of normal and proper use and maintenance (fair wear be used for, domestic or medical applications. -
Page 5: Main Functions
EstateView these alerts can be emailed out. Note – not all commands for Powertxt® are within EstateView, just the main control commands. For a free trial of EstateView please contact your supplier. -
Page 6: Temperature Sensor Drawing
Connected to GSM Network Light (Fading ON/OFF) / GSM Signal Available The master user is the first number to send Powertxt® the first command. Only the master user has authorisation to use all the Rapid Flashing Light Device sending/receiving an SMS features of Powertxt®. -
Page 7: Setting The Master User
Other Users Any users who have not been programmed into this device have Note – If Powertxt® is being used for the first time or it has been no authorisation to control Powertxt®. reset, the master user needs to set the time/date with this 2.3. -
Page 8: Controlling The Power (Output) Manually
2.7. Controlling the Power (Output) Manually To change the master user’s number please send the following Press the Power Button (see figure 1) on the side of Powertxt® SMS command: #14#NewMasterNumber# for 1 second until the power (output) light goes off/on and then again to turn power (output) back on/off. -
Page 9: Deleting An Additional User
Powertxt®. These settings are eg. #129#5#0730#2130# . Powertxt® will switch power ON at saved in Powertxt® and will remain until the socket is reset to its factory settings or the settings are changed by this method 7.30am and switch power OFF at 9.30pm every Friday. -
Page 10: Controlling The Power (Output) By Time Delay – Power On
(output) OFF after set a number of minutes: #138#0#Minutes# e.g. #138#0#125# Powertxt® can be set by SMS command so there is a delay in turning the power (output) ON or OFF. This will turn the power (output) OFF in 125 minutes (2 hours and 5 minutes). - Page 11 Powertxt®. These Powertxt® might be used to turn on an air conditioner to keep settings are saved in Powertxt® and will remain until the socket the room/environment cool.
-
Page 12: Setting The Temperature Range Parameters
If the socket loses external power or is turned off these parameters are still saved. Note - a reading lower than 10 is a low signal, Powertxt® will still function with a poor mobile signal however it may affect... - Page 13 Full Command List 7.3. Status – Time/Day Parameters for Automatic Power Master User (Output) Control Function Command Please send the following SMS command: #128# Setting the Master User #00# 7.4. Status – Time Delay Parameters for Automatic Power (Output) Control Changing the Password #04#OldPW#NewPW# Setting the Time/Date...
-
Page 14: Controlling The Power (Output) By Temperature Range – Off
Controlling the Power (Output) #138#0#Minutes# Additional User by Time Delay – OFF Function Command Setting the Temperature Range #159#0#MinTempValue Parameters (Heating Mode) #MaxTempValue# Turn the Output/Power ON #01#Password# Setting the Temperature Range #159#1#MinTempValue Parameters (Cooling Mode) #MaxTempValue# Turn the Output/Power OFF #02#Password# Controlling the Power (Output) #159#1#... -
Page 15: Signal Strength
Powertxt® won’t 1. The mobile signal strength in the area is 1. Try a different mobile network provider or try Powertxt® in a different respond to any not strong enough for this device to work location commands 2. - Page 16 1. Check the device has not been previously set up by another user reply saying ‘the Master 2. Powertxt® has received set up command 2. The mobile number that sent #00# first will be the master user User already exists’...
Need help?
Do you have a question about the POWERTXT and is the answer not in the manual?
Questions and answers
How do I check if I **** the Master user
To check if you have Master user access on Tekview POWERTXT, send the command `#Password#00#`. If successful, you are the Master user.
This answer is automatically generated