Kenwood NXR-5700 Instruction Manual page 2

NXR-5700/ NXR-5800/ NXR-5900/ NXR-5901 INSTRUCTION MANUAL
VHF DIGITAL BASE-REPEATER / UHF DIGITAL BASE-REPEATER / 800MHz DIGITAL BASE-REPEATER / 900MHz DIGITAL BASE-REPEATER
THANK YOU!
We are grateful you purchased this KENWOOD repeater.
PRECAUTIONS
• Do not expose the repeater to rain or moisture; to prevent fire
or electric shock.
• Do not open the repeater. under any circumstances; to avoid
risk of electric shock.
• Do not expose the repeater to extremely hot or cold
conditions.
• Do not expose the repeater to long periods of direct sunlight,
nor place it close to heating appliances.
• Do not place the repeater in excessively dusty and/or humid
areas, nor on unstable surfaces.
• Do not put the plastic bag used for packing of this equipment
on the place which reaches a small child's hand. It will
become a cause of suffocation if it wears flatly.
• Do not use options not specified by KENWOOD.
• Install optional accessories when power is not applied to the
repeater.
• If you detect an abnormal odor or smoke coming from the
repeater, disconnect the power from the repeater immediately.
Contact your KENWOOD service center or dealer.
NOTICES TO THE USER
◆ Government law prohibits the operation of unlicensed radio
transmitters within the territories under government control.
◆ Illegal operation is punishable by fine and/or imprisonment.
◆ Refer service to qualified technicians only.
One or more of the following statements may be applicable:
FCC WARNING
This equipment generates or uses radio frequency energy. Changes
or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved by the party
responsible/JVCKENWOOD. The user could lose the authority to
operate this equipment if an unauthorized change or modification is
made.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY
THE FCC
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can generate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer for technical assistance.
Firmware Copyrights
The title to and ownership of copyrights for firmware embedded in
KENWOOD product memories are reserved for JVC KENWOOD
Corporation.
◆ Do not install the repeater in explosive atmospheres
(inflammable gas, dust particles, metallic powders, grain
powders, etc.).
◆ This repeater is intended for use as a fixed base station
with the antenna located outdoors on the rooftop or on an
antenna tower.
◆ This repeater is designed for a 13.6 V DC (NXR-5700/ NXR-
5800) or 13.8 V DC (NXR-5900/ NXR-5901) DC power
source. Never use a 24 V DC or higher source to power the
repeater.
◆ Use only the supplied DC cord.
◆ Do not remove the ferrite core attached to the DC cord.
Doing so may cause interference with radio communications.
◆ Do not put anything on top of the repeater. This will obstruct
heat dissipation.
UNPACKING AND CHECKING EQUIPMENT
Note: The following unpacking information is for use by your KENWOOD
dealer, an authorized KENWOOD service center, or the factory.
Carefully unpack the repeater. We recommend that you identify
the items listed in the following table before discarding the
packing material. If any items are missing or have been damaged
during shipment, file a claim with the carrier immediately.
Item
Front glass
Dressed screw
Bracket
Flat head machine screw
Handle
DC cord
Lead wire with connector (15 pin)
Fuse (15 A) : NXR-5700/ NXR-5800
Fuse (7.5A) : NXR-5900/ NXR-5901
SYNC cable
Instruction manual
INSTALLATION
To install the handles onto the front panel of the repeater, align
the handles with the holes on the front panel, then secure the
handles using the supplied screws.
Consult your dealer for installing the repeater and antenna.
MICROPHONE
Connect an optional KMC-30, KMC-35, KMC-9C, or KMC-53
KENWOOD microphone to the MICROPHONE jack on the front
panel.
OCXO UNIT (KXK-3):Option
The OCXO unit (KXK-3) is an Oven Controlled Crystal Oscillator
unit.
The AMBE+2 voice coding Technology embodied in this product
TM
is protected by intellectual property rights including patent rights,
copyrights and trade secrets of Digital Voice Systems, Inc. This
voice coding Technology is licensed solely for use within this
Communications Equipment. The user of this Technology is explicitly
prohibited from attempting to extract, remove, decompile, reverse
engineer, or disassemble the Object Code, or in any other way
convert the Object Code into a human-readable form. U.S. Patent
Nos. #8,315,860, #8,595,002, #6,199,037, #6,912,495, #8,200,497,
#7,970,606, and #8,359,197.
1
Part Number Quantity
B10-2781-XX 1
N08-0563-XX 1
J29-0725-XX 2
N32-4008-XX 4
K01-0421-XX 1
E30-3427-XX 1
E31-3228-XX 1
F52-0042-XX 1
FZB10AX-7R5 1
E3A-0177-XX 1
B5A-2265-XX 1