Advertisement
Quick Links
Z-Wave Keyfob PSR03- A
Z-Wave Scene Remote PSR03- B
Z-Wave Panic PSR03- C
PSR03- A
PSR03- B
PSR03- C
The Remote PSR03 is a simple control can control AV device through Z-
Wave-to-IR extender, and it can also controls 8 lighting groups ON/OFF
via basic set, based on Z-Wave
It is the Z-Wave
TM
plus product, it support the security, OTA... Those
newest features of the Z-Wave
communication protocol designed for home automation, specifically to
remotely control applications in residential and light commercial
environments. The technology uses a low-power RF radio embedded or
retrofitted into home electronics devices and systems, such as lighting,
home access control, entertainment systems and household appliances.
This product can be included and operated in any Z-Wave
with other Z-Wave
TM
certified devices from other manufacturers and/or
other applications. All non-battery operated nodes within the network
will act as repeaters regardless of vendor to increase reliability of the
network.
The device adopts the Z-Wave
network system is all made by Z-Wave
network system will have the advantages as below.
Concurrent multi-channel support reduces external interference.
•
Better RF range, improve about 10 meters in indoor.
•
Support 100 Kbps transmit speed, speed up communication.
•
Function Compare A/B/C
Group
Control
PSR03-XA
PSR03-XB
V
PSR03-XC
TM
technology.
TM
technology. Z-Wave
TM
is a wireless
TM
500 series chip, when your Z-Wave
TM
500 series devices. The
AV
Lock
Control
Control
V
V
TM
network
TM
Panic
V
V
V
Advertisement
Summary of Contents for Z-Wave Keyfob PSR03-A
- Page 1 The technology uses a low-power RF radio embedded or retrofitted into home electronics devices and systems, such as lighting, home access control, entertainment systems and household appliances. This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications.
- Page 2 1.5 seconds and do not release the top-right key in the 4 pressed. Remote PSR03 can control AV device via Z-Wave-to-IR extender and 2. After 3 seconds the LED will turn OFF, after that lighting groups ON/OFF. within 2 seconds, release the keys. If successful,...
- Page 3 switching and special function, the others are control keys. Command: 0x0005 There are two group-buttons that can be switched by pressing central Universal Label: Channel Down key. When the device is switched to group-button 1, LED will light on Group-Button 2 with red color for 3 seconds.
- Page 4 Notice: The configuration NO. 10 could be setting to zero to disable setting the configuration No.7 bit 0. the auto report. Z-Wave Notification * Wake up Notification: After the device adding to the network, it will wake-up once per day in When device is charging, it will send Wake Up Notification to controller default.
- Page 5 “RESET” procedure. Over The Air (OTA) Firmware Update The device support the Z-Wave firmware update via OTA. Let the controller into the firmware update mode, and then hold down the central key and press the top-right key to start the update.
- Page 6 Vali Setting the BASIC command value Name Description Association Def. to turn on the light in the Group 3 association group 3. Basic Set Setting the BASIC command value 0 means using the value of Level to turn on the light. The 0xFF(-1) configuration 2 to set.
-
Page 7: Specifications
Operating Temperature: -10 C ~ 45 Vali For indoor use only. Name Description Def. Specifications subject to change without notice due to continuing product improvement. Z-Wave Supported Command Class COMMAND_CLASS_ZWAVEPLUS_INFO_V2 FCC ID: RHHPSR03 COMMAND_CLASS_BATTERY COMMAND_CLASS_NOTIFICATION_V4 COMMAND_CLASS_ASSOCIATION_V2 FCC Interference Statement COMMAND_CLASS_CONFIGURATION COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2... - Page 8 (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.