Page 1
For indoor use only Dear customer, Thank you for purchasing our KRAUSEN water purifier! You now have water treatment equipment that is at the world’s leading position in today’s water treatment field. It produces pure water that can be consumed directly so the water you drink is cleaner and also beneficial to your health.
Safety Considerations (Be sure to read and remember these safety considerations) In order to avoid property damage and harm to you and others, make note of the following safety precautions. ★Ignoring the following safety precautions could result in a risky situation: Warnings If you ignore contents in this section, it may cause permanent damage to the water purifier or cause serious property damage.
Do not use a power source exceeding When installing or repairing, the machine the machine’s specified value, only use must be disconnected from the power 220V AC power! source! The outlet used for the machine’s Otherwise it may lead to electric current must be greater than the shock.
Page 5
1. Blown-up profile of the water purifier Diagram 1-1Diagram 1-2 2. Electrical diagram Diagram 2...
Page 6
3. Water route map Diagram 3 4. Technical Parameters Voltage AC 220V 50HZ Power Rating 0.05~0.35MPa Suitable Water Pressure ≤0.85Mpa Operating Pressure Inlet Temperature 5-38℃ ≤1000PPM Maximum Inlet Water TDS Value 800 Gallons, approximately 2880 Liters Maximum Daily Water Production Volume Electric Shock Protection Type Type II Municipal...
Page 7
Can further remove small particles in the water, suspended solids, colloids, etc. ④ Fourth stage is RO membrane: Aperture is .0001 micron (0.1 nm), reduces bacterium by 4,000 fold, reduces viruses by over 200 fold, so you can effectively remove bacteria, viruses, heavy metals, pesticide residues, and other harmful substances from the water.
Installation Method This company recommends that professionals install the machine for you, because you must use drills and other power tools in the installation process. If you are installing it yourself, please refer to the following steps and diagrams: 1. Pre-Installation Preparations ①...
Page 9
a little on and then screw the ball valve into the corresponding hole of the 3-way inlet water joint (See Diagram 6). Take out the Ø 9mm water pipe from the accessories box, using scissors cut a suitable length of pipe, connect one end of the pipe with the inlet water ball valve (See Diagram 4), finally screw the nut in place.
Page 10
packaging, put the end of the membrane with the O-ring into the reverse osmosis membrane shell (See Diagram 9) and push it in, finally screw the membrane shell cover back on, and use the membrane shell wrench to tighten the membrane shell cover, put the inlet water pipe into the membrane shell inlet water connector and screw in the nut, then put the membrane shell card into the large single clip and put the water purifier cover back on.
3.Installation Considerations ① When installing the water pipes, cannot install a drain stopper, in addition, for the water pipe bottom connector, the screw nut should have no wire teeth exposed. ② If the inlet water pipe is 9mm, should ensure that the inlet water tube and connector have 30-40cm of straight piping to avoid burst pipe accidents caused by bending in the pipe.
post-activated carbon filter will emit activated carbon powder the first time it is used. So for the first hour the water purifier is operated, do not open the water storage tank. it is recommended that the water produced is thrown out, otherwise the pure water taste may be unusual. 3.
2.The Show Status of Computer Board 1.Computer Board As (diagram12) show Diagram 12 ① The work status of the indicator show A.Working status ; B.First cartridge replacement alarming ; C. Second cartridge replacement alarming D .Third cartridge replacement alarming E. Fifth cartridge replacement alarming Working:The machine start working after 3 seconds when turn on the power,A~E display in turn.
After replacing old filters, they cannot be cleaned and reused; it is recommended that you dispose of them with solid waste garbage. Notes ★ When any of the following situations occur, immediately disconnect the water purifier water source (close the inlet water ball valve) and/or the power source and carry out repairs. ·...
machine is filled High-pressure switch failure Replace the high pressure switch with water, the After checking the non return valve, machine starts System is exhibiting a loss of pressure check whether there is water repeatedly leakage in the pipelines ...
Packing List · Main machine (including RO membra ne ) 1 unit · Water pipe (ø6mm and ø9mm) Each 1 roll · Installation and User Guide 1 copy · Gooseneck faucet · Filter cartridge wrench · Membrane shell wrench · Accessory pack 1 package Consisting of:3 way inlet valve Inlet water ball valve...