aurum AEC-9339A Installation Instructions Manual
  1. Manuals
  2. Brands
  3. aurum Manuals
  4. Accessories
  5. AEC-9339A
  6. Installation instructions manual

aurum AEC-9339A Installation Instructions Manual

The intelligent motion sensor tracking light
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
MOTION SENSOR TRACKING LIGHT
OVERVIEW OF AEC-9339A
INSTALLING THE BULB
Unscrew the lamp cover of the luminaire and
install a 300W J-type lamp.
Re-fit the lamp cover and tighten the screws.
IMPORTANT: THE INTALLATION OF THIS FITTING MUST BE DONE BY A QUALIFIED ELECTRICIAN.
This fitting must be earthed.
Do not mount the luminaire against inflammable surfaces.
The motion detector will not operate correctly if it is installed:
Ⅰ
( ) Near the outlet of a central heating boiler
Ⅱ
( ) Near air conditioning plant
Ⅲ
( ) Pointing directly at moving vehicles
Ⅳ
( ) Within sight of reflection from moving wa
Ⅴ
( ) Where other lamps could shine onto the detector
The maximum rating of this luminaire is 300 Watts. Check that the total load of the circuit. Including this luminaire.
Does not exceed the rating of the circuit cable.
NOTE: This highly responsive unit may occasionally activate due to rapid environmental changes. Allow for approximately
30 seconds warm-up time before the sensor resumes normal activity.
THE INTELLIGENT
INSTALLATION INSTRUCTIONS
Read all instructions before proceeding with the installation
3 motion sensors
ter
WARNING ! ! !
BEFORE ATTEMPTING ANY INSTALLATION OR
MAINTENANCE, ENSURE THAT THE
ELECTRICAL SUPPLY IS SWITCHED OFF AND
THE CIRCUIT FUSES REMOVED OR THE
CIRCUIT BREAKER IS IN THE "OFF"POSITION.
(DRAFT)
Push-button

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AEC-9339A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for aurum AEC-9339A

  • Page 1 THE INTELLIGENT (DRAFT) MOTION SENSOR TRACKING LIGHT INSTALLATION INSTRUCTIONS Read all instructions before proceeding with the installation OVERVIEW OF AEC-9339A Push-button 3 motion sensors INSTALLING THE BULB Unscrew the lamp cover of the luminaire and install a 300W J-type lamp.

  • Page 2: Installation And Wiring Instructions

    MOUNTING THE FITTING To ensure correct operation of the sensor, mount the luminaire that traffic passes across the detector. TOP VIEW GOOD SENSITIVITY LESS SENSITIVITY INSTALLATION AND WIRING INSTRUCTIONS Remove the inset back mounting box from the luminaire. Fit the inset back mounting box onto the wall and tighten the screws at a height that ensures adequate coverage of the area by the infrared detector.
  • Page 3 Please switch off and on the main power, the tracking light now may or may not resume its operation. If the stepper motor stops working, AEC-9339A becomes a regular motion sensor security light. Left 70°...

  • Page 4: Operation

    OPERATION 1. Turn on the wall switch to activate the light, the light is now under All Day mode: light works on day and night NOTE: Allow for approximately 30 seconds warm-up time before the sensor resumes normal activity. 2. To test, walk through the sensor’s detection area. 3.

  • Page 5: Installation Instructions

    THE INTELLIGENT (DRAFT) MOTION SENSOR TRACKING LIGHT INSTALLATION INSTRUCTIONS Read all instructions before proceeding with the installation OVERVIEW OF AEC-9336A Push-button 3 motion sensors INSTALLING THE BULB Unscrew the lamp cover of the luminaire and install a 150W J-type lamp. Re-fit the lamp cover and tighten the screws.
  • Page 6 MOUNTING THE FITTING To ensure correct operation of the sensor, mount the luminaire that traffic passes across the detector. TOP VIEW GOOD SENSITIVITY LESS SENSITIVITY INSTALLATION AND WIRING INSTRUCTIONS Remove the inset back mounting box from the luminaire. Fit the inset back mounting box onto the wall and tighten the screws at a height that ensures adequate coverage of the area by the infrared detector.
  • Page 7 FUNCTION This light is equipped with 3 motion sensors: zone 1 covers 60 degree, zone 2 covers 100 degrees and zone 3 covers 60 degrees. 220 degrees (maximum) in total for 3 zones. ZONE 2 ZONE 1 ZONE 3 TOTAL DETECTION RANGE The light will switch on for 3 minutes and off automatically when heat/ movement is detected.
  • Page 8 OPERATION 1. Turn on the wall switch to activate the light, the light is now under All Day mode: light works on day and night NOTE: Allow for approximately 30 seconds warm-up time before the sensor resumes normal activity. 2. To test, walk through the sensor’s detection area. 3.

This manual is also suitable for:

Aec-9336a

Table of Contents