1. Manuals
  2. Brands
  3. PORTMAN Manuals
  4. Security System
  5. TLU100N
  6. Operation and installation manual

PORTMAN TLU100N Operation And Installation Manual

Gps gprs tracking and alarm system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATION & INSTALLATION MANUAL
GPS GPRS TRACKING AND ALARM SYSTEM TLU100N

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TLU100N and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for PORTMAN TLU100N

  • Page 1 OPERATION & INSTALLATION MANUAL GPS GPRS TRACKING AND ALARM SYSTEM TLU100N...

  • Page 2: Brief Introduction

    REV: 1.9 (STANDARD, TLU100N-TLU200C-PTM-5.09-V1.27 TLU200C2) I. BRIEF INTRODUCTION TLU100N System utilizes the GPRS, GPS and car alarm functions in one unit. The unit continuously gets its precise position and speed information from GPS system. It automatically manages and monitors all of its peripheral equipment and their status all the time.

  • Page 3: Working Mode

    3. Sleeping mode In order to save power, TLU100N can go to sleep mode when duty off and TL-sensor is not trigged for 5 minutes. This feature is configurable. Both “GPS” and “GPRS” or either one of them may be selected to power off. User can setup the automatically wakeup time for the sleep mode to ensure the device will wakeup to work.
  • Page 4 1. TG+: It will send out a event report when TG+ on or off 2. Door TG-: It will send out an event report door open or close. 3. TL sensor: In sleep mode TLU100N will wake up the unit and send out an alert report. In Commercial Confidence...
  • Page 5 B: The sensor ID will be sent to host every 30 seconds after power on in the first 3 minutes, user should power on the sensor device no sooner than the wireless door sensor ID learning function of TLU100N has been launched.

  • Page 6: Status Indicator

    JP1 to ON. The Led will flash three times after one successful device ID learning. 2):Yellow: GPRS indicator. This LED will flash periodically and slowly when the TLU100N system has connected a server by GPRS network. The LED will blink twice when it has received the signal of the GSM base station but has not connected a target server.
  • Page 7 Detail operation decryptions: A. LOGIN dialog window Connect TLU100N and PC with a standard DB9 serial cable, the other terminal plug into the 3-pin connector on the main board. Select the available COM port, and then click “OK”. Note that: it is necessary to power on and reset the PORTMAN device soon after “OK” button clicked.
  • Page 8 (8) Exit: exit the PC-Setup program; the system will exit the PC setup mode and enter the working mode. 1. [User detail]: (1) Set Device ID for TLU100N. The TLU100N ID should be 4 to 8 decimal digitals characters. And the device ID must be unique in order to be identified by the server.
  • Page 9 2.[Geofence]: 1) Circle Geofence setting: Set circular Geofence parameters in left window. The data should be coordinate center of the Geofence and the related radius. 2) Point Geofence setting: Set point Geofence in right part of the window, only GPS coordinate point data is needed. 3) Self-Geofence setting: Self-Geofence is a fresh idea for vehicle guard.
  • Page 10 In normal working mode (DUTY ON), the system will use the configurations as defined in this section. To activate the automatic report, please select “√” in checkbox and fill in data in the textbox. The reports will be summarized as (1) Intelligent report Parameters: On/Off, Report time when moving, Report time when stop, and threshold speed.
  • Page 11 [on/off] SEND REPORT IF ADC1 GO DOWN [down voltage] V for [debounce time] SEC [on/off] SEND REPORT IF ADC1 ENTER/EXIT [min voltage] V TO [max voltage] V for [debounce time] SEC Note: AD1 input voltage range is 0~3.3v, it must connect a resistance to share the voltage if the detected voltage higher than 3.3v,.
  • Page 12 Special command for SMS mode: If the TLU100N is not in the GPRS online status, user can send command &&Y02 or &&Y04 to ask unit to connect to server. This command can be sent from any device via SMS;...
  • Page 13 To enable the particular trigger reports by click the box. 2) Sleep mode (when Duty-Off) (1) TLU100N can go to sleep mode when duty off and TL-sensor is not trigged for 5 minutes. In sleep mode, GPS & GPRS will be disabled.

  • Page 14: Frequently Asked Questions

    Simplification: No connect unit’s hard wire to vehicles. The hard wire door TG-; TG+; 1 A/D; ext. power will not be used. Notes: if you first time use TLU100N, please press the reset button once to active built-in battery work.

  • Page 15: Appendix 1: Event Code Summary

    6-pin connector is for firmware downloading or debug, user do not need to care them. 5. Question: TLU100N can go to sleep mode when duty off and TL-sensor is not trigged for 5 minutes, but are they independent? Reply: The TLU100N system will enter sleep mode when all the following conditions met at the same time.
  • Page 16 141 Power of temperature sensor is low 144 Exit defined Circular Geofence area4 (Self Geofence) 145 Enter defined Circular Geofence area4 (Self Geofence) 150 ‘Help’ request 151 User Duty on 152 User Duty off 154 Exit defined Circular Geofence area5 155 Enter defined Circular Geofence area5 156 Door Close (Wireless Door Sensor 1) 157 Door Open (Wireless Door Sensor 1)
  • Page 17 284 Enter point Geofence 4 285 Enter point Geofence 5 286 Enter point Geofence 6 287 Enter point Geofence 7 288 Enter point Geofence 8 289 Enter point Geofence 9 290 Enter point Geofence 10 291 Enter point Geofence 11 292 Enter point Geofence 12 293 Enter point Geofence 13 294 Enter point Geofence 14...

  • Page 18: Appendix 2: Tlu100N Specifications

    Ext power supply charge full time (solar panel 20 hours not work) Solar panel charge full time (no Ext power 50 hours supply and TLU100N is sleeping all the time) Normal work time (no charging) 30 days Solar panel parameters Valid solar panel area...

  • Page 19: Appendix 3 Wireless Accessories (Optional) Wireless Keypad

    Warm Start: <38 sec. (50%), <45 sec. (90%) Cold Start: <90 sec. (50%), <170 sec. (90%) Antenna Type Built-in IO Connection 1* three pin connector PC_SETUP cable 1* 5 wires Vehicle battery, TG+ input & Door Trigger input 1*button RESET Communication GPRS \SMS\RS232 Environmental...
  • Page 20 In Commercial Confidence...
  • Page 21 VI. Federal Communications Commission (FCC) Statement You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.

Table of Contents