Unimax S1 Quick Start Manual

Hide thumbs

Table of Contents

Quick Links

Download this manual

Dash Cam S1

Quick Start Guide

E11074 / Revised Edition V2 / November 2015

Table of Contents

Summary of Contents for Unimax S1

Page 1 Dash Cam S1 Quick Start Guide E11074 / Revised Edition V2 / November 2015...
Page 2 NOTE: • The screenshots in this Quick Start Guide are for reference only.
Page 3 Hardware MicroSD card Micro USB port slot Power/Wi-Fi button Lens GPS port NFC sensor Speaker Battery LED Recording/ Emergency Record Snapshot LED butto n button...
Page 4 Press the microSD card to eject, then pull it out. IMPORTANT! • For first time use of your Dash Cam S1 and to ensure the best video saving quality, format a Class 10 microSD card to FAT32. • Do not remove the microSD card during recording. Doing so...
Page 5 IMPORTANT! • The Wi-Fi function gets activated in about 40 seconds after turning your Dash Cam S1 on. • Before connecting your Dash Cam S1 and mobile device, ensure that the Wi-Fi LED is solid blue indicating that Wi-Fi is...
Page 6 • To save power, press the Power/Wi-Fi button to disable the Wi- Fi function. • In car mode, your Dash Cam S1 overwrites the oldest recorded files when your microSD card is full. • In portable mode, your Dash Cam S1 stops recording...
Page 7 Installing UniMax Dash Cam app on your mobile device Do any of these three methods to download and install UniMax Dash Cam: • Place your NFC-enabled Android mobile device on the NFC sensor of your Dash Cam S1 to download UniMax Dash Cam and install it on your mobile device.
Page 8: Connecting Your Mobile Device
Dash Cam S1 2. Turn on the Wi-Fi function of your mobile device. 3. From the list of networks, tap Dash Cam S1 (default SSID). 4. Enter the default password (1234567890) and tap Join (for iOS device) or Connect (Android device).
Page 9 NOTES: • Your Dash Cam S1 comes with a dual car charger with 1A and 2.1A output, which makes it easier to power on and charge other electronic devices at the same time.
Page 10 Registering for your free 500GB ASUS WebStorage Register your Dash Cam S1 on ASUS WebStorage to get a free 500GB cloud storage for a year. 1. Locate the Serial number Serial No: F9YUFK000001 and Check number on the 90006270046200 15060-673200000000000...
Page 11: Live Streaming
Using UniMax Dash Cam UniMax Dash Cam is an app that lets you to enjoy live streaming, play videos, or download media files for sharing to your mobile device. portable Disconnect Live streaming 1. From your mobile device, launch UniMax Das.h Cam.
Page 12 Using One Shot 1. From your mobile device, launch UniMax Das.h Cam . 2. Tap the Preview tab, then tap One Shot. 3. Tap to capture the photo. 4. Tap the Playback tab check the photos. Capturing continuous photos 1. From your mobile device, launch UniMax Das.h Cam .
Page 13: Capturing Time-Lapse Photos
Capturing time-lapse photos 1. From your mobile device, launch UniMax Das.h Cam. 2. Tap the Preview tab, then tap Time Lapse. 3. Tap to capture photos. Tap to stop time-lapse. 4. Tap the Playback tab check the photos. NOTE: You can change the time lapse frequency in the Settings tab.
Page 14 1. From your mobile device, launch UniMax Das.h Cam . 2. Tap the Playback tab, then tap Video or Photo. You can get the file list from the Dash Cam S1 microSD card. 3. Select the video or photo that you want to play or view.
Page 15: Deleting Files
Deleting files 1. From your mobile device, launch UniMax Das.h Cam. 2. Tap the Playback tab, then tap Video or Photo. 3. Tap on the file you want to delete. 4. Tap Delete on the confirmation message. Installing the Media Player 1.
Page 16 5. Follow the onscreen instructions to complete the installation. NOTE: For normal video playback, ensure that K-Lite Codec (.mov codec) is installed on your computer. Reviewing the GPS log Click to share videos to YouTube Click to remove a file Click to import a file Click to import a folder Click to view the driving...
Page 17 NOTE: * Ensure that your computer is connected to the Inter- net to be able to review the driving route on the map. 1. Using a USB cable, connect your car camcorder to your computer. 2. On your computer, launch the Media Player. 3.
Page 18 Settings FUNCTION DESCRIPTION Sets the video resolution. Video Resolution Available options: 1920x1080@30f ; 1280x720@30f NOTE: Default resolution for One Photo, Time Lapse, and Photo Burst is 1920x1080. • When enabled, this function can record videos Ultra Wide Angle at 150 degrees. Mode •...
Page 19 Internet. • You must be signed in to ASUS WebStorage. The Serial number and Check number are on the packaging box of your Dash Cam S1. For details, refer to the section Registering for your free 500GB ASUS WebStorage.
Page 20 Portable mode: Time lapse, One photo, Photo burst functions are available. In this mode, your Dash Cam S1 stops recording when your microSD card is full. Image Rotate Auto: The image direction will be adjusted automatically by G-sensor.
Page 21 Adjusts the volume level Monitor Mode When this function is enabled and the scene does not change in 60 seconds, your Dash Cam S1 stops recording and enters the standby mode. Once any movement is detected, your Dash Cam S1 automatically starts recording.
Page 22 FUNCTION DESCRIPTION Adjusts the exposure level Format SD card Select OK to format the memory card installed on the device. CAUTION! Before formatting the SD card, ensure that you have backed up your files from your SD card. Battery Status Shows battery status Factory Default Select OK to reset all settings to factory default...
Page 23: Button Functions
Button functions STATUS ACTION Power on Press the Power/Wi-Fi button and the Wi-Fi function is activated automatically. Power off Press and hold the Power/Wi-Fi button for three (3) seconds until you hear a beeping sound. Turn Wi-Fi on/off When power is on, press the Power/Wi-Fi button to turn Wi-Fi on/off.
Page 24: Led Indicators
LED indicators STATUS ACTION Solid white Power on. Wi-Fi is still oV. Solid blue Power on and Wi-Fi is available. Power/Wi-Fi NOTE: The Wi-Fi function starts in button about 40 seconds after turning it on. LED OV Power oV Solid red Recording videos Red LED flashes every time a photo is Flashing red...
Page 25 STATUS ACTION Firmware Update Flashing green and red NOTE: An alert sound notifies you when the firmware update is completed. Flashing green, MicroSD card is not installed. red, white, and In portable mode. blue MicroSD card is full. Please save your files, or format the SD card.
Page 26: Specifications Summary
Specifications summary Image sensor SONY COMS Sensor Video resolution 1920x1080P (30fps) / 1280x720P (30fps) Lens angle Wide angle lens, FOV 150 degree (Diagonal) Aperture F/1.8 Battery Built-in 720mAh Li-Polymer battery App control Android / iOS apps for streaming video and control device Interface Micro USB 2.0 (Power) / Mini USB (GPS)
Page 27: Troubleshooting
Store How do I connect my Dash Cam S1 to my mobile device? 1. Turn on your Dash Cam S1. The Wi-Fi function starts in 40 seconds after turning it on. 2. Turn on the Wi-Fi function of your mobile device.
Page 28 What are the Dash Cam S1 modes? Upon launching the Unimax Dash Cam app, you will see either of these two icons at the top of the screen: Car mode: Loop recording, emergency recording, and monitor mode functions are available.
Page 29 Dash Cam S1. I cannot find a previously-recorded emergency video file. Your Dash Cam S1 can save up to ten (10) emergency recording. When the maximum emergency recording limit is reached, the newly- saved recording overwrites the oldest recording.
Page 30 FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Page 31 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.