Summary of Contents for Stoneridge EZ-ELD 1.0
- Page 1 Document: Page Date: EZ-ELD – PRODUCT MANUAL 1 of 14 24 Jan 2017 PRODUCT MANUAL EZ-ELD™...
-
Page 2: Table Of Contents
Document: Page Date: EZ-ELD – PRODUCT MANUAL 2 of 14 24 Jan 2017 Summary 1 Compliance Statement ........................3 2 Kit contents ............................3 3 Connector options ..........................4 Remove the 9 pin connector ...................... 5 Insert the new connector ......................6 Wire extender (installation on site with little space) .............. -
Page 3: Compliance Statement
Document: Page Date: EZ-ELD – PRODUCT MANUAL 3 of 14 24 Jan 2017 1 Compliance Statement This device has: FCC ID: 2AKA8-ELD100A0 22098-ELD100A0 Model: ELD1.0 PMN: EZ-ELD This equipment complies with Industry Canada and FCC radiation exposure limits set forth for an uncontrolled environment. -
Page 4: Connector Options
Document: Page Date: EZ-ELD – PRODUCT MANUAL 4 of 14 24 Jan 2017 3 Connector options The EZ-ELD is shipped with the 9-pin connector already fitted. However, it also has 3 other connector options (6-pin, OBDII Light and Medium Duty Vehicles and OBII Volvo/Mack): 6P Connector 9P Connector OBII Volvo/Mack... -
Page 5: Remove The 9 Pin Connector
Document: Page Date: EZ-ELD – PRODUCT MANUAL 5 of 14 24 Jan 2017 3.1 Remove the 9 pin connector To change the connector type follow the guidelines of the item below. ELD MAIN MODULE 9P CONNECTOR ELD Dongle with OBDII Volvo/Mack Connector for Dongle Configuration (Same for OBDII Light and Medium Duty (Same for 6P Connector) -
Page 6: Insert The New Connector
Document: Page Date: EZ-ELD – PRODUCT MANUAL 6 of 14 24 Jan 2017 Insert a "key" in the crack and make a lever to the inside of the module. Do one side at a time. Side 1 unlocked Part 1 and 2 are unlocked. Unplug the white connector 3.2 Insert the new connector Plug the white connector on the module. - Page 7 Document: Page Date: EZ-ELD – PRODUCT MANUAL 7 of 14 24 Jan 2017 Rotate the connector so that the wires Position the connector on the module wrapping, thus improving the accommodation and press it until you hear two clicks In accordance with the need the connector can be mounted in one of two ways, rotated 180°.
-
Page 8: Wire Extender (Installation On Site With Little Space)
Document: Page Date: EZ-ELD – PRODUCT MANUAL 8 of 14 24 Jan 2017 3.3 Wire extender (installation on site with little space) Wire extender ELD main module Double side OBDII connector. You can Cover adapter extender whip also use the 6 and 9 pins. Bottom Cover Top Cover The Top Cover is used in the ELD main module and the Bottom Cover is used in the... - Page 9 Document: Page Date: EZ-ELD – PRODUCT MANUAL 9 of 14 24 Jan 2017 Connect the end of the harness with plug connector on the top cover. Wrap the wires to facilitate assembly connector Bottom Cover ELD module OBDII connector. You can also use the 6 and 9 pins.
- Page 10 Document: Page Date: EZ-ELD – PRODUCT MANUAL 10 of 14 24 Jan 2017 Plug the connector of the wire at connector Position the connector on the top cover OBDII. Attention to the correct position and press it until you hear two clicks ELD module with extensor harness Bond the double-sided tape on the module for mounting the same...
-
Page 11: Installation Instructions
Document: Page Date: EZ-ELD – PRODUCT MANUAL 11 of 14 24 Jan 2017 4 Installation Instructions: 1. Locate the truck’s diagnostic port of the vehicle. Depending on the make and model, it may or may not be easy to locate. There are several locations to find the diagnostic port: Under the dash or under the steering column/wheel on the left or right, On the left or right of the pedals, above the pedals. - Page 12 Document: Page Date: EZ-ELD – PRODUCT MANUAL 12 of 14 24 Jan 2017 2. Attach the dongle to the vehicle’s diagnostic port. Rotate the collar to align the collar tabs with the matching slot on the diagnostic port, press firmly until the adapter cable is fully connected, then rotate the collar clockwise until it clicks: Correct Installation: Incorrect Installation:...
-
Page 13: Led And Sound Patterns
Document: Page Date: EZ-ELD – PRODUCT MANUAL 13 of 14 24 Jan 2017 5 Led and Sound patterns Continuous blink and sound Led blink 4 times/Buzzer Led blink 3 times Led blink 2 times Led blink 1 times Solid 1 Chirp 2 Chirps 3 Chirps Light and Sound Pattern... -
Page 14: Download The Ez-Eld™ App
Document: Page Date: EZ-ELD – PRODUCT MANUAL 14 of 14 24 Jan 2017 6 Download the EZ-ELD™ App Download the EZ-ELD App for Android and IOS devices. Search for EZ-ELD in the Google Play Store for Android phones and search for EZ-ELD in the App Store for iPhones and iPads.
Need help?
Do you have a question about the EZ-ELD 1.0 and is the answer not in the manual?
Questions and answers