Landi Renzo V05 Instruction Manual
  1. Manuals
  2. Brands
  3. Landi Renzo Manuals
  4. Test Equipment
  5. V05
  6. Instruction manual

Landi Renzo V05 Instruction Manual

Programmer tester
Hide thumbs
Table of Contents

Advertisement

Quick Links

INSTRUCTIONS MANUAL
P
T
ROGRAMMER
ESTER
Mod. V05
190164440

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the V05 and is the answer not in the manual?

Questions and answers

Summary of Contents for Landi Renzo V05

  • Page 1 INSTRUCTIONS MANUAL ROGRAMMER ESTER Mod. V05 190164440...

  • Page 2: Table Of Contents

    MEMORY DELETION ..................... pag 13 DIAGNOSIS MODE ......................pag 14 CARBURATION LEARNING PROCEDURE ..............pag 15 LANDI RENZO S.P.A. reserves the right to make improvements or modifications to its products at any time, at its own judgement and without notice thereof.

  • Page 3: Tester Parameters And Values That Can Be Selected

    TPS signal. The Programmer Tester Mod. V05 is supplied directly by the cable linking it with the LCS-A/1 V05 central unit. OFFERS (fig.1)
  • Page 4 Overlap time ..................................0-1 sec. Type of TPS (throttle position sensor) ....5-0V, 0-5V linear, 0-12V switch,12-0V switch, Mono Bosch, TPS adapter Indicator sensor type ........................Landi Renzo, AEB, 0-90 Ω Lambda sensor type .......................... 0-1V, 0-5V, 5-0V, 0.8-1.6V Lambda sensor reading delay ..........................0-1250 sec.

  • Page 5: Arrangement Of Pages Of Programmer Tester Mod. V05

    DATA DISPLAY ARRANGEMENT OF PAGES OF PROGRAMMER TESTER mod. V05 Programmer tester Mod. V05...

  • Page 6: Data Display Page

    When the cursor is in position L []]]]]] R it indicates that the mixture measured by the lambda sensor is LEAN When the cursor is in position L ]]]]]][ R the mixture measured by the lambda sensor is RICH button takes you back to the MAIN MENU page. Pressing the Landi Renzo S.p.A.

  • Page 7: Example Of Programming

    FOR CHANGE If in modify value mode you do not want to confirm the figure just varied, pressing the button restores the previous value (fig. 11). 2000 RPM Modify not confirmed by pressing ESC button, fig.11 Programmer tester Mod. V05...

  • Page 8: Number Of Cylinders (Ignition)

    Linear TPS 5-0V: the voltage of 5V indicates throttle closed, 0V the throttle is fully open. SWITCH 0-12V: the voltage of 0V indicates throttle closed, 12V the throttle is fully open. fig.16 SWITCH 12-0V: the voltage of 12V indicates throttle closed, 0V the throttle is fully open. Landi Renzo S.p.A.

  • Page 9: Type Of Tps

    INDICATOR SENSOR TYPE fig.17 (fig. 18) LANDI RENZO: select this parameter for all LANDI RENZO sensors, both LPG and CNG. AEB: if an AEB-type LPG sensor is used. O-90W: for LPG indicator sensors that have an internal resistor of 0-90Ω.

  • Page 10: Simulation Type

    By selecting the square wave type of emulation it is possible to set the parameters indicated below (fig. 23); change these parameters only by following the instructions of the LANDI RENZO technical service. HIGH TIME : the time of the signal emulating a rich mixture (fig. 22).

  • Page 11: Maximum Open Trhottle Option

    • Check on the road at what TPS value there is irregular carburation and set this value for TPS FOR MAXIMUM OPEN THROTTLE. OPTION ENABLED fig. 27 OPEN THROTTLE POSITION 100 STEPS fig. 28 TPS FOR MAXIMUM OPEN THROTTLE 2.8 V fig. 29 Programmer tester Mod. V05...

  • Page 12: Maximum Actuator Position

    The cut-off option must be used only after the central unit has acquired the default position of the linear actuator NOT ENABLED with stepper motor. fig. 33 Landi Renzo S.p.A.

  • Page 13: Minimum Rpm For Cutoff

    100 steps (fig. 38). Therefore, in the case of resetting, re-enter the parameters that may have been changed and which correspond to the vehicle. 100 STEPS fig. 37 MEMORY DELETION fig. 38 Programmer tester Mod. V05...

  • Page 14: Diagnosis Mode

    If you do not want to complete zeroing the memory of the diagnosis function, press or change “page” with one Diagnosis memory reset page fig. 42 of the direction buttons. SENSOR NOT WORKING Disconnected sensor diagnosis page fig. 43 Landi Renzo S.p.A.

  • Page 15: Carburation Learning Procedure

    Overlap time (during changeover from petrol to gas) ......... 0.400 sec. Type of TPS (throttle position sensor) ............linear 0-5V Indicator sensor type (gas level) .............. Landi Renzo Lambda sensor type ..................... 0-1V Lambda sensor reading delay ................5 sec.
  • Page 16 LANDI RENZO S.p.A. via Fratelli Cervi 75/2 42100 Reggio Emilia ITALY Tel. (+39)/0522/382678 -Telex 531050 RELAND - Fax (+39)/0522/382906 E-mail: info@landi.it - Internet Site: http://www.Landi.it SISTEMA QUALITÁ CERTIFICATO Accredited by the Dutch Council for EN 9001/ISO 9001/ BS5750 Certification APPROVED BY BVQI...

Table of Contents