Summary of Contents for Thermo Solar ECO2 160
- Page 3 TECHNICAL INSTALLATION MANUAL FOR THE TECHNICAL INSTALLATION SOLAR SYSTEM MANUAL FOR THE TABLE OF CONTENTS SOLAR SYSTEM TABLE OF CONTENTS INSTRUCTIONS FOR THE MOUNTING OF THE SUPPORT BASE ON TILT ROOF Page 4-5 INSTRUCTIONS FOR THE MOUNTING DESCRIPTION OF THE PLUMBING ASSEMBLY BETWEEN THE WATER TANK OF THE SUPPORT BASE ON TILT ROOF Page 4-5 AND COLLECTOR ON TILT ROOF...
- Page 4 INSTRUCTIONS FOR THE MOUNTING OF THE photo 1 photo 2 DÅ min 900mm - photo 3 We first check that the height of the pitch roof from the We screw the stainless steel straps to the oblong wood highest top until the lower part of the solar system is at or flooring as at (photo 1) and we leave the one side least 3800mm-minimum.
- Page 5 SUPPORT BASE ON TILT ROOF photo 4 photo 5 DÇ max 1080mm photo 6 top side (photo 3) reposition again the tiles as they were before. We repeat the same process on the upper side of the When we have finished with the vertical long bracket support base with the difference that: supports (A-A) we position and screw at their lower ATTENTION:...
- Page 6 DESCRIPTION OF THE PLUMBING ASSEMBLY BETWEEN THE 13 18...
- Page 7 WATER TANK AND COLLECTOR ON TILT ROOF 01 Solar water tank 02 Water tank’s support angle 03 Solar Collector(s) 04 Collector’s support angle 05 Hot water supply (outlet) 06 Brass Tee ó" 07 Pressure relief valve of hot water supply ó" 08 Pressure relief valve female ó"...
- Page 8 INSTRUCTIONS FOR THE MOUNTING OF photo 1 photo 2 photo 3 We place the metallic small plate (F) at the shorter bracket support (D) in the slot of the back backside of the long bracket support (A) at the side of the long bracket support (A) as at (photo 1). lower part as at (photo 3) and screw it tight.
- Page 9 THE SUPPORT BASE ON FLAT ROOF photo 4 photo 5 photo 6 We place the horizontal support angle (B) of the We have to take care that the solar support base water tank-collector as at (photo 4), and screw it has the correct orientation (see page 17) and when on the long bracket supports (A) being careful that we have installed the collector/s and the water tank...
- Page 10 DESCRIPTION OF THE PLUMBING ASSEMBLY BETWEEN 13 15...
- Page 11 THE WATER TANK AND COLLECTOR ON FLAT ROOF 01 Solar water tank 02 Water tank’s support angle 03 Solar Collector(s) 04 Collector’s support angle 05 Hot water supply (outlet) 06 Brass Tee ó" 07 Pressure relief valve of hot water supply ó" 08 Pressure relief valve female ó"...
- Page 12 INSTRUCTIONS FOR THE MOUNTING OF THE photo 1 μ ∞ photo 3 We first position the water tank Afterwards we position the on the top of the support base metallic corner supports of of the solar system and then we collector(s) (H) as at (photo 1) install the collector(s) being that we have to insert them first...
- Page 13 THE SOLAR SYSTEM ON FLAT ROOF photo 5 photo 4 installed at the lower side of the collector(s) and the carefully all of the connections for any possible other edge at the filler neck of the bottle, as long as we leakages, we position the protection side cover of have already lifted the bottle and the plastic tube (L) at aluminium (J) as at (photo 2) and the protection...
- Page 14 1450 cm 2150 cm 2150 cm 2150 cm 3300 cm 1000 cm TYPES OF SOLAR SYSTEMS / PROPORTION OF ANTIFREEZE LIQUID – WATER MINIMUM ECO2 160 ECO2 200 ECO2 200 ECO2 250 ECO2 300 ECO2 300 ECO2 160 TEMPERATURE 2mÇ...
- Page 15 TECHNICAL CHARACTERISTICS OF THE WATER TANK 1.EXTERNAL CASING: Stainless Steel cover AISI 304BA thickness 0.5mm or Anodized aluminium 2.INSULATION: Polyourethane thickness 60mm, density 40kg/m3 3.INNER TANK: Stainless Steel AISI 316L HiMo thickness 2mm or Steel UST 37.2 thickness 3mm enameled according to DIN 4753 Teil3. 4.HEAT EXCHANGER: Stainless Steel AISI 316L HiMo thickness 1mm or Steel UST 37.2 thickness 1.5mm enameled according to DIN 4753 Teil3.
- Page 16 ELECTRICAL CONNECTION DIAGRAM OF AUXILIARY HEATING RESISTANCE 28. Thermostat DOUBLE ENERGY 29. Thermal security switch 30. Temperature regulator 31. Earth terminal 32. Electricity conductors 33. Electric resistance 34. Conductor joint 35. Metallic support for the electric joint 36. Sealing flange of the electric resistance 37.
- Page 17 TRIPLE ENERGY ORIENTATION OF SOLAR SYSTEM The thermal performance of the solar system is optimized when mounted facing South (when Northern hemisphere). The actual performance however is minimal decreased when the system is oriented less than 45o degrees South East or South West.
- Page 18 INSTALLATION OF 6 SOLAR SYSTEMS ON LINE DN 20mm (3/4”) DN 20mm (3/4”) DN 20mm (3/4”) DN 20mm (3/4”) DN 20mm (3/4”) DN 20mm (3/4”) 1.All of the tubes that we will use for the installation must have INLET OF OUTLET OF HOT the same length and geometry.
- Page 19 INSTALLATION OF SOLAR COLLECTORS ON LINE (20sq.m.) 2mÇ 2mÇ 2mÇ 2mÇ 2mÇ 2mÇ 2mÇ 2mÇ 2mÇ 2mÇ 2mÇ 2mÇ OUTLET OF HOT WATER 1. OBSTRUCTION GATE VALVE 2. COLLECTOR SENSOR INLET OF 3. THERMOMETER COLD WATER 4. AUTOMATIC RELIEF VALVE...
Need help?
Do you have a question about the ECO2 160 and is the answer not in the manual?
Questions and answers