Summary of Contents for KCI RADF13
- Page 1 Ver 1.2 USER'S MANUAL RADS11 / RADF13 RADIO REMOTE CONTROL SYSTEMS 0341 RADS11 and RADF13 Users Manual ver1.2.doc KCI Hoists Corp. reserves the right to modify this information without prior notification. Page 1 of 20...
-
Page 2: Table Of Contents
Pushbutton as a Key board for Hoist Condition Monitoring Unit....16 Figure 10 LCD representing Tared Load ..............16 RADS11 and RADF13 Users Manual ver1.2.doc KCI Hoists Corp. reserves the right to modify this information without prior notification. Page 2 of 20... -
Page 3: Conformity Declaration
93/44/EEC Machinery Directive. Hämeenlinna, 21st of Jun 2002 Signed: Ari Kiviniitty Managing Director RADS11 and RADF13 Users Manual ver1.2.doc KCI Hoists Corp. reserves the right to modify this information without prior notification. Page 3 of 20... -
Page 4: Description
5ºC to 35ºC 41F to 95F Operating Time 12h at 50% RAD-TS model. 8h at 50% RAD-TF model. RADS11 and RADF13 Users Manual ver1.2.doc KCI Hoists Corp. reserves the right to modify this information without prior notification. Page 4 of 20... -
Page 5: Safety Precautions
Never power the equipment other than with the specified power supply. Never allow unqualified personnel to operate the equipment. RADS11 and RADF13 Users Manual ver1.2.doc KCI Hoists Corp. reserves the right to modify this information without prior notification. Page 5 of 20... -
Page 6: Installation
(keys, coins, etc.). Always keep contacts clean. Never leave batteries in direct sunlight. RADS11 and RADF13 Users Manual ver1.2.doc KCI Hoists Corp. reserves the right to modify this information without prior notification. Page 6 of 20... -
Page 7: Receiver
The way to connect the receiver box to the crane's electrical installations is using a cable with a terminal multiple-pole connector: Note: See attached drilling pattern sheet. RADS11 and RADF13 Users Manual ver1.2.doc KCI Hoists Corp. reserves the right to modify this information without prior notification. Page 7 of 20... -
Page 8: Figure 3 Receiver To Power Electric Circuit Connection
8A fuse(s) has to be provided in the crane control panel for the for the output relays. RADS11 and RADF13 Users Manual ver1.2.doc KCI Hoists Corp. reserves the right to modify this information without prior notification. Page 8 of 20... -
Page 9: Figure 4 Connection Diagram For Rads11
Use only the approved cables. Select the appropriate voltage on the receiver, (230, 115 or 48 Vac). RADS11 and RADF13 Users Manual ver1.2.doc KCI Hoists Corp. reserves the right to modify this information without prior notification. Page 9 of 20... -
Page 10: Figure 5 Connection Diagram For Radf13
Use only the approved cables. Select the appropriate voltage on the receiver, (230, 115 or 48 Vac). RADS11 and RADF13 Users Manual ver1.2.doc KCI Hoists Corp. reserves the right to modify this information without prior notification. Page 10 of 20... -
Page 11: Starting-Up
5. Press START The transmitter LED should light up green indicating that the transmitter is transmitting. RADS11 and RADF13 Users Manual ver1.2.doc KCI Hoists Corp. reserves the right to modify this information without prior notification. Page 11 of 20... -
Page 12: Figure 6 Rads11 And Radf13 Transmitters
Flashing ON (quickly) each time a good frame is received with ID correct. This means that the receiver has recognised the transmitter’s identification code RADS11 and RADF13 Users Manual ver1.2.doc KCI Hoists Corp. reserves the right to modify this information without prior notification. Page 12 of 20... -
Page 13: Spurious Disturbance
After pushing the START button, STOP relays will be activated. K2/START and K12/HORN relays are activated only when the start button is pushed. Relays K13 and K14 on RADF13 system will be activated to the corresponding state of the Hoist Selector. -
Page 14: Use
Remember that you are going to control remotely a moving piece of machinery. The safety instructions described in chapter 3 of this manual must be strictly adhered to. RADS11 and RADF13 Users Manual ver1.2.doc KCI Hoists Corp. reserves the right to modify this information without prior notification. Page 14 of 20... -
Page 15: How To Access To The Hoist Condition Monitoring Unit In Radf13 System. Service Mode
MODE. 4.1 General Description of Service Mode For RADF13 systems, there is a special “Service Mode” of operation for maintenance and set up of the Hoist Condition Monitoring Unit via radio. This unit is connected to the receiver RAD-RF by a serial data communication CL20mA. -
Page 16: Keys For Moving Within The Menus
4.5 Resetting the Tared Load. Pressing the ESC button for several seconds performs the reset of the Tared Load. RADS11 and RADF13 Users Manual ver1.2.doc KCI Hoists Corp. reserves the right to modify this information without prior notification. Page 16 of 20... -
Page 17: Exiting Service Mode
• “CURRENT LOOP FAULT”: This message will appear whenever the receiver RADF13 is not able to read any data frame from the Hoist Condition Monitoring Unit. This message can be seen when switching the unit to display mode or by unplugging Hoist Condition Monitoring Unit from the receiver. -
Page 18: Maintenance
Check the contacts on the fuses and the fuse-holders. Battery charger and batteries: Keep all contacts clean. RADS11 and RADF13 Users Manual ver1.2.doc KCI Hoists Corp. reserves the right to modify this information without prior notification. Page 18 of 20... -
Page 19: Locating Break-Downs
Technical Assistance Service, together with a description of the problem and the status of the LEDs. RADS11 and RADF13 Users Manual ver 1.2.doc KCI Hoists Corp. reserves the right to modif this information without prior notification. Page 19 of 20... -
Page 20: Drilling Pattern Sheet
6 Drilling pattern sheet. NO SCALE 255,5mm = 10” 169,5mm = 6,7” RADS11 and RADF13 Users Manual ver1.2.doc KCI Hoists Corp. reserves the right to modify this information without prior notification. Page 20 of 20...
Need help?
Do you have a question about the RADF13 and is the answer not in the manual?
Questions and answers