Advertisement
2. INTRODUCTION & SPECIFICATION
electric hand-pushed hover mower with a 280mm (10.5") cutting
width. composite deck for light weight durability. electric motor
combined with an emergency cut-out switch for safety. optimum
cutting height between 15 and 25mm. supplied with 10m mains cable
and Bs plug. folding handle to enable easy storage.
3 (see
fig.1)
4
6
model no: .................................................................................... Gl53
drive type: .................................................................. Hand operated
cutting Width: ............................................................... 280mm (10.5")
cutting deck cover: ..............................Plastic moulding (composite)
supply:................................................................................ 230V - 1ph
Power: ...................................................................................... 1000W
two cutting Heights: ................................................15mm and 25mm
cable length: ................................................................................10m
cutting Blades: ...................Plastic (nylon) moulding x 3 [21 supplied]
Ingress Protection: ....................................................................... IPX4
Weight: ........................................................................................ 7.8kg
measured sound Power level .................................................. 75dBA
Guaranteed sound Power level: .............................................. 96dBA
this is a class II appliance and does not need an earth connection.
tubular Handle
Power lever
safety Button &
switch Housing
cable clip
© Jack sealey limited 2013
1
see section 7
Warning symbols.
5
2
cable strain
relief hook.
mains cable
fig.1
Original Language Version
3. CONTENTS AND ASSEMBLY
Item descrIPtIon
1
upper handle sub assembly
2
lower handle
3
cable strain relief hook
4
cable clips
5
Handle clamp c/w bolt and washer
6
lower handle pivot thumb screws
7
cutter deck c/w motor, impellor and 3 blades
8
supplied blades
3.1.
check that you have all the above details in the packaging.
In the unlikely event of any missing or damaged parts,
contact your sealey dealer immediately. retain the
packaging.
3.2
Assembly:- (no tools required)
3.2.1
loop the cable strain relief hook (item 3) on to the upper
handle tubular frame (item 1) in the position indicated.
3.2.2. thread the mains cable as illustrated in fig.1 through the
cable strain relief hook (item 3). this is an important safety
feature preventing the mains cable from being accidentally
pulled from switch connections.
3.2.3. fit the lower handle frame (item 2) to the pivot lugs of the
cutter deck (item 7) using the pivot thumb screws (item 6). A
captive nut inside the motor cover enables the thumb screws
to clamp the tubular frame hand tight.
3.2.4. fit the upper handle sub assembly (item 1) containing the
switch and cable to the lower handle (item 2) paying
7
attention to the cable run. clamp the frame with (item 5)
details, see fig.2.
3.2.5
Position the three cable clips (item 4), clip to tubular frame
and finally clip the cable which runs from motor to switch.
3.3
Blade fitting and setting:- (no tools required)
3.3.1
decide on the grass cutting length required, a choice of
15mm or 25mm is available. In fig.3 the blades are shown at
the 15mm setting. observe blade orientation.
3.3.2
to remove blades and set to the 25mm length, push the
blade toward the hub tab horizontally. slide from the
keyhole slot small end to the large end and lift off.
3.3.3. refit or change blades by the opposite approach and pull the
blade from the hub tab. the 25mm length setting is inboard
of the 15mm setting on the same hub. DO NOT remove hub.
NOTE: the blades will only fit one way, see fig.3. DO NOT
force fit the blades in the wrong way.
WARNING! never use blades other than the spares
supplied. never fit metal cutting elements. further spares
available from your sealey dealer.
QtY
21
fig.2
Gl53
Issue no: 1 - 14/01/13
1
1
1
3
2
2
3
Advertisement
