INSTALLATION ......................3-4 WIRING CONNECTION ....................5 OPERATION ....................... 6 LOCATION OF THE KEYS ..................6 POWER ON/OFF THE UNIT ..................7 MAIN MENU ........................7 SETUP ........................... 7 RESET FUNCTION ...................... 9 SLIGHTFOG AFTER OPERATION................. 9 RADIO OPERATION ....................9 USB OPERATION ......................
INSTALLATION Notes: Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.
OPERATION (Press “ ”button on the remote control or POWER ON/OFF THE UNIT BND button on the front panel to exit to previous menu.) Press the button to turn on/off the unit. MAIN MENU SYSTEM SETTINGS Press and hold SETUP/ENTER button on the remote control for 2 seconds ,Then Press “...
Page 8
OPERATION 1).V surround Press “ ”button on the remote control to select Off/Concert/Church/Soft/Wide/Live. Press “ ” button on the remote control or BND button on the front panel to exit to previous menu. 3). Radio Area Press “ ”button on the remote control to select Europe/America.
OPERATION RADIO OPERATION Press “ ”button on the remote control to select 4:3 pan scan/16:9. SWITCHING TO THE RADIO MODE Press MODE button or in the main menu to 2).Adjust select RADIO mode. The following information Press “ ”button on the remote control to will appear on the display select Brightness/Contrast/Hue/Saturation/ Sharpness.
OPERATION Automatic Story & Program Scanning: signal is not good. If you change it to MONO mode the noise will be reduced. Also you can - Program scanning turn it on/off in SEL menu. Shortly press AMS button on the remote control to scan preset station which is stored in Local on/off: number 1~6 buttons .
Page 11
OPERATION playback. root press BND button will enter the left side. 4) Stop playback Press vol +/- to select the When playing audio/video content, press the button on the remote controller or BND button Press back to the right side. Press of the panel to stop the playing.
OPERATION track. Press the INT button again to resume return to the folder. normal playback. *During IMAGE playback, the following b.When playing video/image sources, the INT buttons are not available: RDM, INT. button is not available. AV IN OPERATION 9) Playback in Random When playing video/audio content, press the Switching to AV IN mode...
OPERATION 4. SEL menu instruction manual of your mobile phone on how to operate Bluetooth.) Repeatedly press SEL button on the remote 2) “CAR KIT” should appear in the list on control will show the SEL menu as below: your mobile phone, please select “Car Bass---Treble---Balance---Fader---EQ---Loud KIT”.
Page 14
OPERATION set at minimum. Traffic Program Identification Listening to Traffic Announcement identification data traffic Press TA button shortly on the remote information-broadcasting station control to switch on/off TA mode. In panel TA: Traffic Announcement Identification Press an hold MOD button for 2 seconds. Identification data showing...
OPERATION DAB OPERATION 1) Press AMS button on remote control for full scan. there isn't any station, Scroll display "NO STATION FOUND". 2) Press buttons (5/3)button it is station up/down. Shortly press M1-M6 button(remote control) button to read M1-M6 station. If Read Empty Preset, Display "NO SAVED"...
Page 17
REMOTE CONTROL 1. MODE Press to change the source. 2. POWER Press it to turn the unit ON or OFF 3. BAND: To select FM1, FM2, FM3, MW1, MW2 radio bands. 4. ENTER/SETUP Long press to return to previous menu, short press to enter next menu;...
SPECIFICATION GENERAL Power Supply Requirements : DC 12 Volts, Negative Ground Chassis Dimensions : 100 (W) x 100 (D) x 75 (H) Tone Controls Bass (at 100 Hz) : ±10 dB Treble (at 10 kHz) : ±10 dB Maximum Output Power : 4x40 watts Current Drain : 10 Ampere (max.) (For Normal Power Version)