Table of Contents
Advertisement
Quick Links
Installation instructions
Accessories
Please check you received the following accessories with your Fisher & Paykel washer. You will find them inside
the drum or attached to the packaging.
• 2 x Inlet hose(s) (for models WH8560J and WH7560J only 1 x Inlet hose supplied)
• 1 x Drain hose guide
• 1 x Installation instructions and user guide
• 1 x Spanner
• 1 x Installation leaflet (attached to the top of the washer)
• 1 x Inlet valve cap (excluding WH8560J and WH7560J models)
Unpacking
To ensure the best performance from your new washer please follow the instructions below.
Removing the packaging
1. Remove the outer packaging (including the polystyrene packer and plastic wrapping). All packaging must be
removed prior to use. Ensure these materials are kept out of reach of children.
https://producthelp.fisherpaykel.com/au/Wash/Front_Loaders/QuickSmart/WH7560J3/User_Guide_WH7560J3/03_Installation_instruction
Updated: Sat, 13 Jan 2018 05:02:40 GMT
Powered by
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Fisher WH8560F
-
Page 1: Installation Instructions
Installation instructions Accessories Please check you received the following accessories with your Fisher & Paykel washer. You will find them inside the drum or attached to the packaging. • 2 x Inlet hose(s) (for models WH8560J and WH7560J only 1 x Inlet hose supplied) •... - Page 2 A small amount of water may be seen inside the packaging and inside the washer. This is the result of factory testing and is normal. 2. Tilt the machine backwards and ‘walk’ it off the base one foot at a time. Not doing so may cause damage to your floor and washer.
-
Page 3: Product Dimensions
Product dimensions WH8560F/ WH8060F/ WH7560P/ Property (mm) WH8560P/ WH8060P WH7560J WH8560J A. Overall height of product. B. Overall width of product. C. Overall depth of product (including dial and door when closed). D. Depth of door open. 1065 1065 1010 E. -
Page 4: Leveling The Machine
The exact height of your washer is dependent on how far the feet are extended from the base of the machine. The space where you install your washer needs to be at least 40mm wider and 20mm deeper than its dimensions.= •... -
Page 5: Connecting To The Water Supply
Connecting to the water supply Inlet hose(s) New hose sets provided with the washer • should be used to connect the washer to the water mains. Old hose sets should not be re-used. • We recommend the inlet hose(s) are •... -
Page 6: Water Supply Requirements
RMC TVA 75HFS Adjustable between 35°C – 55°C RMC TVA 50HP For instantaneous gas hot water supply Water supply requirements: • Inlet water pressure: Maximum 1MPa (150psi), Minimum 30kPa (4.5psi) • Inlet water flow rate: Minimum 6 litres/minute Cold supply only: If you only have a cold water supply, the inlet valve cap (blanking cap) which came with your washer must be connected to the hot inlet valve (with the exception of WH8560J and WH7560J models). -
Page 7: Attaching Drain Hose To Spigot
If the drain hose is placed on the ground or if the standpipe or tub is less than 800mm • high, the washing machine will continuously drain while being filled (siphon). Regularly check that your standpipe or tub is free from lint or other obstructions, which •... -
Page 8: Completing The Installation
• Fisher & Paykel dealer or Fisher & Paykel trained and supported service technician. Spare Parts Available from your Fisher & Paykel dealer or a Fisher & Paykel trained and supported service technician. Hose Inlet Long (2m) Part No. 422680P Hose Inlet Large Bore Part No. - Page 9 button. The machine will start to fill. ◦ Observe the machine for any problems (eg leaking from the hose(s), excess noise or vibrations). ◦ The washer will beep and display any faults on the screen if there are any problems. Refer to ‘Before you call for Service’...
Need help?
Do you have a question about the WH8560F and is the answer not in the manual?
Questions and answers