Summary of Contents for Systech Corporation CAREU U1 Lite
-
Page 1: User Guide
CAREU U1 PLUS User Gu CAREU U1 LITE PLUS User Guide Version: 0.1 Reference No.: AVL Date: 2015/4/1 SYSTEMS & TECHNOLOGY COR... - Page 2 General Information If any breakdown occurs due to the operation of the described product or users’ improper handling in accordance with the instructions of the document, S&T shall be liable for the General Conditions based on the delivery of the described product and the content of the document. This product is not designed for the use of life support appliances, devices or systems and thence a malfunction of the product might reasonably be expected to make personal injury.
-
Page 3: Table Of Contents
1.3 Overview ......................1 1.4 Hardware Architecture ..................3 1.5 Related Document ................... 3 Chapter 2 Taking a Tour of CAREU U1 LITE PLUS ........... 4 2.1 Dimensions ....................... 4 2.2 PIN Assignment ....................4 Chapter 3 Getting Started with CAREU U1 LITE PLUS ........5 3.1 Device Configuration .................. -
Page 4: Chapter 1 Introduction
Peripheral data indicates the status of various peripherals connected to and/or controlled by the device. Among the best features of the CAREU U1 LITE PLUS Vehicle Tracker, in particular, they transmit data in ASCII mode (Intellitrac X Series compatible mode) or binary mode. - Page 5 GPS LED GSM LED Power & I/O Connector RS-232/CAN Connector USB Connector GPS Antenna Connector Reset Switch Speaker/MIC Connector...
-
Page 6: Hardware Architecture
1.4 Hardware Architecture As hardware is concerned, the CAREU U1 LITE PLUS is comprised of a micro-controller, regulator, GPS receiver, 2G/3G modem, G-Force sensor, flash memory data storage. ● Users can connect PC's Hyper Terminal to the diagnostic setting port for the AVL configuration. -
Page 7: Chapter 2 Taking A Tour Of Careu U1 Lite Plus
Chapter 2 Taking a Tour of CAREU U1 LITE PLUS 2.1 Dimensions Dimensions (L x W x H): 105.5mm x 72mm x 28.5mm 2.2 PIN Assignment PWR/IO Connector Pin# Signal Name Description Electrical Characteristic DC IN Power supply input DCIN = DC 8V to 30V,... -
Page 8: Chapter 3 Getting Started With Careu U1 Lite Plus
SPK- Audio output Chapter 3 Getting Started with CAREU U1 LITE PLUS To install the the CAREU U1 LITE PLUS device, follow the instructions below for basic operations 3.1 Device Configuration 1. Connected the serial port 1 to PC COM port 2. - Page 9 6. For Com port properties, configure as follows: Baud Rate --> 115200 bps Data Bits --> 8 Parity --> None Stop Bits --> 1 Flow Control --> None 7. In the connection that you have just set up, click File | Properties. Select the [Connect To] tab.
- Page 10 9. In the [ASCII Sending] group box. Select both Send line ends with line feeds and Echo typed characters locally. Press the OK button. 10.Connect your the CAREU U1 LITE PLUS device and power on,The device startup message will be displayed.
- Page 11 11. In [HyperTerminal] window, type in the command "AT$VERSION?" and press the Enter key. The hardware and firmware version will show. As long as your [HyperTerminal] window appears as the screenshot below, a connection between the device and your system has already been built up and working. It is time to send all configuration commands.
-
Page 12: Communication Settings
3.2 Communication Settings The CAREU U1 LITE PLUS Vehicle Tracker communicates with your control center by either SMS or 2G/3G (TCP/UDP). Before the device is installed into a vehicle, communication parameters should be set. 1. SMS Configuration Use AT$SMSDST command to set a SMS control center phone number or short code. -
Page 13: Gps Tracking Configurations
AT$HB=60,1 (Heartbeat setting) OK Please refer to the CAREU U1 LITE PLUS Protocol Document for more command details. 3.3 GPS Tracking Configurations After the device communication settings are done, the remote GPS tracking is ready to function. The setting of GPS tracking can be done by using AT$PDSR command. -
Page 14: Firmware Upgrade
The main page of the Intelli FleetWeb appears as below: 3.4 Firmware Upgrade The firmware of the CAREU U1 LITE PLUS can only be updated through USB interface. With the firmware loader tool provided by S&T, firmware update can be done for... -
Page 15: Chapter 4 Technical Specification
the device. Such firmware loader runs on Windows-based systems. To upgrade the firmware, follow the procedure below 1. Connect the device to your PC with the USB cable. 2. Connect the device to power. 3. Power on the device. 4. Run ServerUSeries.exe. A window displays as follows: Press browse the button to browse to the firmware provided by S&T. - Page 16 Antenna: Internal GPS Module: Vendor: uBlox MAX-M8Q/W Sensitivity: -167 dB ( GPS & GLONASS ) -165 dB ( GPS & BeiDou ) -166 dB ( GPS ) Antenna: External Time to First Fix: Cold Start: 26 Seconds at open sky ( GPS &...
- Page 17 Temperature Operating: –20 °C to +60 °C(With Battery) Operating: –20 °C to +70 °C(Without Battery) Storage: –20 °C to +80°C Logging positions User Report Sets Note: The specification herein is subject to change without prior notice. Systems & Technology Corp. (S&T), founded in 1987, is a market leader in Automatic Vehicle Locating (AVL) solutions, Geographical Information Systems (GIS) and navigation.
-
Page 18: Chapter 5 Regulation
Chapter 5 Regulation Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Page 19: Chapter 6 Safety Information
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Chapter 6 Safety Information...