Related Manuals for Orbit OC 7520
Summary of Contents for Orbit OC 7520
- Page 1 OC7520_GBM_21312 Programmable Display for BCD parallel Data Ports OC 7520 Owner’s Manual ORBIT CONTROLS AG Zürcherstrasse 137 CH-8952 Schlieren-Zürich Tel: +41 44 730 2753 Info@orbitcontrols.ch www.orbitcontrols.ch...
-
Page 3: Unpacking Instructions
Vor dem Einschalten Überzeugen Sie sich, ob Ihre Sendung das richtige Gerät Orbit Controls Modell OC 7520 beinhaltet, einschließlich einer Betriebsanleitung OC 7520. Vor dem Einschalten des Gerätes überprüfen Sie die Anschlüsse und die Versorgungsspannung. Ein falsch angeschlossenes Gerät kann beschädigt werden und damit auch die mitverbundene Folgeelektronik. -
Page 4: Table Of Contents
Index Programmable Display for BCD parallel Data ports OC7520 Page 5 SPECIFICATIONS FRONT PANEL PROGRAMMING with Options PROGRAMMING without Options TERNINALS (Rear of the instrument) Upper Terminals (Supply 9-36VDC) Upper Terminals (Supply 230VAC) BCD data inputs, RS232 data outputs and Analogue Outputs BCD parallel Inputs Excitation –... -
Page 5: Programmable Display For Bcd Parallel Data Ports Oc7520
Four Set Points Data Bus operation up to 63 Units Orbit Controls OC7520 is a programmable display for connection to parallel BCD data ports. It is designed as a remote display for digital meters, programmable controllers, printers etc. In the measuring mode the 6 digit display shows the data from the port. In the programming mode the display shows the parameters. -
Page 6: Specifications
SPECIFICATIONS 0 ... ± 999999, 7 segments red or green, 14.7 mm. DISPLAY: INPUTS: BCD parallel, 5…24V positive or negative logic. DATA OUTPUT: RS232/RS485: 1 Start, 1 Stop, 8 bit, no Parity. Address: 00 = RS232, 01…31 = RS485 (250V RMS Isolation) Baud Rate: 300 to 19200 bd. - Page 7 PROGRAMMING (with build-in options RS232 and Analogue output) Software Version 7520_V5.hex CS: 1120 The menu will be opened with the key MENU. With the same key the submenu will scroll at the display. The required parameter will be confirmed with ACK. Its value will be set with UP or DOWN.
- Page 8 Example for setting of Fn bcd: BCD data input: 123456 POS Display Transmission via RS232 100000 120000 123000 123400 1234 123450 12345 123456 123456 PROGRAMMING (without options) DISPLAY FUNCTION MENU Set Point 1 001000 Select with UP, DOWN and SET MENU Set Point 2 001500...
-
Page 9: Upper Terminals (Supply 230Vac)
TERMINALS (Rear of the instrument) Upper Terminals (Supply 24VDC) Set Points with transistor outputs Upper Terminals (Supply 230VAC) Set Points with four Relays The relay and the transistor outputs can be combined. The relays can be assembled to close or to open when activated. -
Page 10: Bcd Parallel Inputs
BCD Data Inputs, RS232/485 Data Outputs and Analogue Outputs BCD Parallel Inputs INPUT INPUT 800 000 400 000 200 000 100 000 80 000 40 000 20 000 10 000 8 000 4 000 2 000 1 000 SIGN SIGN do not use do not use do not use... -
Page 11: Excitation – Supply For External Sensors
Excitation - supply for external sensors... -
Page 12: Serial Data Port
SERIAL DATA PORT RS Data Format Format: 1 Start, 1 Stop, 8 Bit no Parity Baud Rate: Menu step bAUd: 300 to 19200 bd Termination: Menu step dElin: Null CrLF Carrige Return Line Feed (0xd und 0xa) Line Feed (0xa) Carrige Return (0xd) nonE without... -
Page 13: Burst Test And Recommended Connections
BURST TEST and RECOMMENDED CONNECTIONS Tester: Burst-Surge Generator HILO, Model CE-Tester E.U.T.: OC7520, SN:990818, Supply 230VA Mode: BCD parallel Input: 123456 Display: 123456 Test Conditions According to Norms: IEC 801-4 IEC 1000-4-4 EN 50052-1 Test Set - Up Test Results Zone 1: 2kV Burst Display without change 123456...