The R&TTE Directive We, the manufacturer (WALTOP International Corp.) hereby declare that this equipment (Bluetooth Pen Pad- Flying Pad), model RSK-T06 is in compliance with the essential requirements and other relevant provisions of Directive 1995/5/EC. FCC Caution This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions This device may not cause harmful interference, and This device must accept any interference received,...
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Contents The R&TTE Directive FCC Caution Federal Communication Commission Interference Statement Introduction — Hardware introduction — Function introduction — How to change the battery — How to replace the Pen Refill — Software Introduction of Bluetooth Pen Pad Manager — Wireless mode —...
Introduction Thank you for purchasing this product. Bluetooth Pen Pad provides two modes of connection with a PC: Wireless mode and wired mode. Both modes provide a convenient working environment. Please note that the setup procedures are different from wired and wireless mode and these will be stressed through this manual.
— How to replace the Pen Refill Pull out the used pen tip with the Refill Tweezers provided. Insert the Pen Refill to the pen. Press firmly on a hard surface for 5 seconds till the Pen Refill is locked.
— Software Introduction of Bluetooth Pen Pad Manager • Pen (Absolute mode) – the area of the Bluetooth Pen Pad corresponds to the whole area of the screen. For example, if place your wireless pen at the top right hand corner the mouse pointer will always be at the top right of the screen.
— Wireless mode Bluetooth Pen Pad + Bluetooth Adapter on PC Make sure that you have powerful batteries in the battery chart and switch the power button to on. — Wired mode Bluetooth Pen Pad + USB Cable on PC. —...
— USB mode When the USB cable is initially connected to the Tablet, the Red LED will flash once and the Blue LED will flash continuously. The Blue LED will be on when the pen is detected within the working area but will be off as soon as the pen touches the tablet.
Important information for you to read! Bluetooth Pen Pad ships with a bundled Broadcom IC Bluetooth device and WIDCOMM Bluetooth Software. We do not test with Bluetooth software from other manufactures, but in many cases, Our Bluetooth Pen Pad will work well with these third party Bluetooth software packages if their device support WIDCOMM Bluetooth Software version 5.0.1.1600.
software and then, install the WIDCOMM Bluetooth software that shipped with the released CD in the package. Installation Please insert the CD-Rom in the package into your CD-ROM Device. The software will automatically begin. There are three parts in AUTO RUN. One is Bluetooth Pen Pad Driver, another is Bluetooth Software and the other is Application software.
STEP 2 Hardware installation Please plug the USB cable firmly to Bluetooth Pen Pad and to your PC. — Wireless mode You have to install Bluetooth Pen pad Driver and Bluetooth software to complete the necessary steps. Install Bluetooth Pen Pad Driver Click “Bluetooth Pen Pad Manager”...
Page 14
– data for Microsoft Bluetooth software” The data will be added into Microsoft Bluetooth software automatically. Please click “finish”. STEP 2 Hardware installations Please plug the Bluetooth Adapter to your PC now. Finding new Hardware. Welcome to the Found new hardware Wizard.
Page 15
Install the software automaticall. Completing the Found New Hardware Wizard. (P.S After that, Bluetooth icon will be showed in Windows System Tray) Finding new Hardware again Welcome to the found new Hardware Wizard...
Page 16
Install the software automatically Completing the Found NewHardware Wizard. Click “ Finish” STEP 3 Start to Pair Bluetooth Pen Pad Click on the START button, the SETTINGS, and then select CONTROL PANEL. In the CONTROL PANEL, you can find the BLUETOOTH DEVICE icon.
Page 17
Double Click BLUETOOTH DEVICE icon. Then, Please click “ ADD” Add Bluetooth Device Wizard. My Device is setup and ready to be found Searching...
Page 18
Select the Bluetooth Device that you want to add. Please click “ Next” Passkey Please choose “Don’t use a passkey” Connecting Completing Click “ Finish”...
Page 19
Bluetooth Device If your OS system is Windows 2000/XP, you can install WIDCOMM Bluetooth software. WIDCOMM Bluetooth software setup STEP 1 Software Installation Click “Windows 2000/XP – WIDCOMM Bluetooth software” Welcome The software will automatically begin. The window welcomes you to install shield Wizard for Bluetooth software.
Page 20
License Agreement Read the license agreement, if you accept, select the check button. To continue, click “Next” Locating of installation If you wish to select another location where the software will be installed, click “Change” and select or enter a new location. The default location is recommended.
Page 21
Copying The installation process will now begin. Please wait while files are being copied to your computer. The progress bar will indicate the portion that has been completed. Driver Signature (Windows XP only) You will be prompted with a driver Signature Notice.
Page 22
STEP 2 Bluetooth Adapter Hardware Installations If you have successfully inserted the WIDCOMM Bluetooth software pleases continue.The green LED (light) on the device will be lit, if Bluetooth Adapter is successfully inserted. To continue, click “OK ” Finish Now you have completed the installation of the WIDCOMM Bluetooth...
Page 23
STEP 3 Initial Set up (only for the very first time installation) Open My Bluetooth Place Double-click the My Bluetooth Places on your desktop. Run Initial Bluetooth Configuration The Initial Bluetooth Configuration Wizard will appear. The default options are recommended. You may uncheck them respectively if you do not wish the My...
Page 24
the icon in which you identify yourself to another Bluetooth user. To continue, click “Next” Each Bluetooth device that wishes to connect to your computer must have a unique Computer name (different to all other users connecting). Bluetooth Service The Initial Bluetooth configuration Wizard window will now allow you to enable...
Page 25
wish to offer. Disable or enable by clicking one the check box next to the name of the service you wish to alter. □ :Service enabled □: Service disabled. By default all services are enabled (all check boxes ticked). The default setting is recommended. You can choose to disable or enable services at any time.
Page 26
STEP 4 Start to Pair Bluetooth Pen Pad Open My Bluetooth Places Tip: Bluetooth System Tray The Bluetooth icon in the Windows Systems Tray indicates the USB Bluetooth Adapter Status. Enabled Disabled Connected Blue with Blue with Blue with Green White To open My Bluetooth Places, go to your windows desktop and double-click the icon.
Page 27
Please double-click the Bluetooth Pen Pad. And click “OK”. Make sure Bluetooth Pen Pad is power on and the Bluetooth Adapter is plugging into PC and the icon in Windows Systems Trays is Blue with White. The very first time you want to connect Bluetooth Pen Pad to a new PC (or new Adapter).
Once the icon is , the Bluetooth Pen Pad works now. If you would like to know more about how to use Bluetooth Adapter, please reference from the user manual of USB Bluetooth Adapter. How to Unpairing Once you want to cut down the connection between Bluetooth Pen Pad with your PC.
Page 29
The Bluetooth Connection Status Windows will appear. Click Disconnect. Now you can safely disconnect your Bluetooth Pen Pad. • Above Windows XP Service Pack 2 with Microsoft Bluetooth software Select Bluetooth Pen Pad, then click Remove to disconnect your Bluetooth Pen Pad. To make sure to cut down the connection, once you have done the above step from PC side, please also keep pressing the unpairing button on the...
Troubleshooting When I search for my Bluetooth Pen Pad, many devices appear that I do not recognize. Because Bluetooth 1.2 class 2 has a range of up to 10 meters, you will detect devices beyond the Bluetooth Pen Pad that you are searching for. My Bluetooth Pen Pad connection drops out when I use my cordless phone.
Page 31
pairing section. b.You will need to restart your PC. There is a longer than usually delay with my Bluetooth Pen Pad. You will need to move closer to your computer and try replacing the batteries. Or you may check whether your PC is stable. Or maybe there are other 2.4G devices interfere now.
Product Specification Bluetooth Pen Pad Item Description Technology Electromagnetic Bluetooth Version 1.2 Class 2 Connection 10 meters Distance Dimension 239*251*30mm Active Area 6”*4.5”(152mm*114mm) Weight 493g (545g with batteries) Writing height 10mm Macro key 12 (Press 1.5 seconds to work ) Hot key Unpairing for pushing 5 seconds AA battery* 2 (Rechargeable battery...
Page 33
Connection Bluetooth Version 1.2 Class 2 Interface USB 1.1 Full speed Resolution 1000 Lpi Pen Pressure 512 Levels Bluetooth mode :162 report/per second Reporter Rate USB mode :183 report/per second Windows 2000/ XP SP1 : only support WIDCOMM driver (5.0.1.1600)which only works with Broadcom chip IC Bluetooth dongle dongle...
Maintenance Do not drop, puncture or disassemble the tablet. Remove batteries during long periods between uses. Avoid all contact with water and dry hands before using. Do not expose the tablet to high temperature or leave it in direct sunlight. Avoid pressing hard on the tablet body.
Environment Environment always influences the receiving quality of your tablet. The best environment for your tablet is where no other cordless products are functioning, such as microwave ovens. Cement walls and wooden walls absorb radio wave and decrease receiving quality. Open space without barriers is the best environment for your tablet.