RD-GB2A BUS AMPLIFIER INTRODUCTION First and foremost we would like to thank you for purchasing this product. Our commitment to achieving the satisfaction of customers like you is manifested through our ISO-9001 certification and the manufacture of products like the one you have just purchased. Its advanced technology and strict quality control will ensure that customers and users enjoy the numerous features that this device offers.
RD-GB2A BUS AMPLIFIER CHARACTERISTICS RD-GB2A Bus amplifier module with simplified wiring (non-polarised 2-wire bus). RD-GB2A Bus amplifier module for the GB2 system that allows the following operating modes: Repeater mode, enables the distance of the door panel bus or monitor bus to be increased when it exceeds 80 m (distance with Golmar RAP-2150 2x1mm twisted pair cable).
RD-GB2A BUS AMPLIFIER OPERATING MODES 'Repeater' operating mode: This operating mode enables the distance of the door panel bus or monitor bus to be increased when it exceeds 80 m (distance with Golmar RAP-2150 2x1mm twisted pair cable). The RD-GB2A module requires an FA-GB2A power supply. Install the RD-GB2A module with an FA-GB2A power supply.
RD-GB2A BUS AMPLIFIER OPERATING MODES 'Router' operating mode: This operating mode enables the installation to have up to 8 risers/verticals. One RD-GB2A module per riser/column. Up to 23 monitors and apartments with a Vesta2 monitor per riser. (Mixed inst with telephones max. 23 elements). Up to 18 monitors and apartments with a Vesta7 monitor per riser.
RD-GB2A BUS AMPLIFIER OPERATING MODES 'Gateway' operating mode: This operating mode enables a system with one general entrance door panel and up to 8 interior buildings. One RD-GB2A amplifier per interior building. Up to 23 monitors and apartments with a Vesta2 monitor per interior building. (Mixed installations with telephones max.
RD-GB2A BUS AMPLIFIER DESCRIPTION OF THE RD-GB2A BUS AMPLIFIER MODULE Description: FRONT Model: RD-GB2/A BOTTOM Bus-IN Bus-OUT Tx/Rx In-Use NoRoute Amp-ON OUT DS Status LEDs. Interior door panel connection terminals Configuration buttons (general entrance door panel system). Configuration DIP switch.
RD-GB2A BUS AMPLIFIER INSTALLATION Description of the DIP switches: The DIP switches of the RD-GB2A module enable configuration of one of the 3 operating modes, module address number and end of line. Repeater mode enables door panel bus or monitor bus distance to be increased when it exceeds 80 m. Router mode enables the installation to have up to 8 risers/columns.
To configure the end of line of the RD-GB2A module: DIP switch 6: Leave the intermediate modules in the OFF position. Factory setting. Description of the status LEDs: Model: RD-GB2/A The RD-GB2A module has the following status LEDs: Bus-IN Bus-OUT Bus In: LED on: When the bus cable is connected to the 'IN' terminal.
Page 10
The RD-GB2A module has 2 operating modes for setting gain: Function 'Fixed' mode: The RD-GB2A module will always use the gain configured in the module. buttons Model: RD-GB2/A Step 1: Press button on one of the monitors connected to the RD-GB2A module that requires video gain adjustment;...
RD-GB2A BUS AMPLIFIER INSTALLATION Configuring the button code (up to 32 addresses/apartments) The EL610D button module needs to be configured in order to assign a call code to the buttons. Carry out this configuration with the DIP switch located at the back of the module. Depending on the configuration option selected, the buttons will be assigned with a certain call code.
Page 19
RD-GB2A BUS AMPLIFIER INSTALLATION Configuring single button module codes: EL632 GB2 EL632 GB2A Front Back VESTA2 Monitor code C1 NA1 C2 AP+ AP- P1 P2 BUSBUS 0/32 Relay 1 Relay 2 12Vdc Not used Not used EL610D Module No. Not used Not used Not used Not used...
Page 20
RD-GB2A BUS AMPLIFIER INSTALLATION Continued from previous page. EL610D Monitor code Module No. Not used Not used C d 20 Not used Not used C d 19 Not used Not used C d 18 Not used Not used C d 17 Not used Not used C d 16...
RD-GB2A BUS AMPLIFIER INSTALLATION Configuring the button code (up to 128 addresses/apartments) The EL610D button module needs to be configured in order to assign a call code to the buttons. Carry out this configuration with the DIP switch located at the back of the module.
Page 27
RD-GB2A BUS AMPLIFIER INSTALLATION Configuring single button module codes (up to 71 addresses / apartments): EL632 GB2A Front Back Monitor code C1 NA1 C2 AP+ AP- P1 P2 BUSBUS 0/32 Relay 1 Relay 2 12Vdc Not used Not used EL610D Module No.
Page 28
RD-GB2A BUS AMPLIFIER INSTALLATION Continued from previous page. EL610D Monitor code Module No. Code 20 Not used Not used Code 19 Not used Not used Code 18 Not used Not used Code 17 Not used Not used Code 16 Not used Not used Module No.
Page 29
RD-GB2A BUS AMPLIFIER INSTALLATION Continued from previous page. EL610D Monitor code Module No. Code 8 Not used Not used Code 7 Not used Not used Code 6 Not used Not used . 38 Code 5 Not used Not used Code 4 Not used Not used Module No.
Page 30
RD-GB2A BUS AMPLIFIER INSTALLATION Continued from previous page. EL610D Monitor code Module No. Code 28 Not used Not used Code 27 Not used Not used Code 26 Not used Not used Code 25 Not used Not used Code 24 Not used Not used Module No.
RD-GB2A BUS AMPLIFIER WIRING DIAGRAMS: Installation of a video door entry system with RD-GB2A 'repeater' mode (increase the distance of the monitor Bus). VESTA2 Master ( ) 3 APARTMENT 23 End of line VESTA2 Master APARTMENT 2 ( ) 3 End of line VESTA2...
RD-GB2A BUS AMPLIFIER WIRING DIAGRAMS: Installation of a video door entry system with RD-GB2A 'repeater' mode (increase the distance of the door panel Bus). VESTA2 Master ( ) 3 ( ) 3 Apartment 23 End of line VESTA2 Master Apartment 2 ( ) 3 ( ) 3 End of...
Page 33
RD-GB2A BUS AMPLIFIER WIRING DIAGRAMS: Installation of a video door entry system with RD-GB2A 'router' mode (enables up to 8 risers/verticals). VESTA2 VESTA2 Stairway Stairway Master Master ( ) 3 ( ) 3 APARTMENT 23 APARTMENT 23 ( ) 3 ( ) 3 End of End of...
Page 34
RD-GB2A BUS AMPLIFIER WIRING DIAGRAMS: Installation of a video door entry system with RD-GB2A 'gateway' mode (general entrance door panel and up to 8 interior buildings). VESTA2 VESTA2 Building Building Master Master ( ) 3 ( ) 3 ( ) 3 ( ) 3 APARTMENT 23 APARTMENT 23...
Page 35
RD-GB2A BUS AMPLIFIER WIRING DIAGRAMS: Installation of a video door entry system with RD-GB2A 'gateway' mode (general entrance door panel and up to 8 interior buildings). VESTA2 VESTA2 Building Building Master Master ( ) 3 ( ) 3 ( ) 3 ( ) 3 APARTMENT 23 APARTMENT 23...
RD-GB2A BUS AMPLIFIER WIRING DIAGRAMS: Installation of a video door entry system with access panels, DP-GB2A distributor for door panels and Golmar DC lock release. Video door entry system: To the distributors (building floors) Audio door entry system: To the telephones (building floors) Mains 100~240Vac GB /A...
RD-GB2A BUS AMPLIFIER WIRING DIAGRAMS: Connection of Golmar DC and AC lock releases. Connection of 2 DC lock releases without 'AP': Access panel ( ) 2 Button panel Coded panel To the FA-GB2/A power supply C1 NA1 C2 AP+ AP- P1 P2 BUSBUS Relay 1 Relay 2 12Vdc...