Advertisement
Quick Links
Thank you for your purchase of your Xtreme Fat Tire Bike.
INITIAL INSPECTION:
Please inspect your packaging upon arrival for any damage that may have occurred in shipping.
If you see any damage take photographs, and call us immediately so we can file a claim if
necessary. Please do not remove the bike until we file a claim with FedEx.
RETURNS:
Please note: As per our policy on the website, returns must be made within 3 days of delivery
and are subject to a 20% restocking fee. You must call us at 757-635-5160 if you intend to return
the bike so we can issue a RMA (Return Material Authorization) number. Returns will not be
accepted any other way. After the 3-day period, all sales are final. Return shipping costs are the
responsibility of the buyer, unless the bike is damaged in shipping.
CHARGE-BACKS:
We will do everything in our power to honor the 1-year warranty on parts and ensure your
satisfaction with our products. If you have a defective part, you must return it to us before we can
send you a replacement part. A chargeback to your credit card company is not a method of
correcting a warranty issue as you already have your electric bike. We consider charge-backs as
a form of theft when you already have your merchandise and will prosecute them to the full
extent of the law and you will be responsible for all attorneys' fees.
LEGAL ACTION:
Fatty AT E-Bikes is a limited liability corporation located in Deerfield Beach, FL. Any legal
action taken against the company, or its employees or owners must be in the jurisdiction of
Broward County, Florida.
Advertisement
Summary of Contents for Fat Tire Xtreme Bikes E-Bike
- Page 1 Thank you for your purchase of your Xtreme Fat Tire Bike. INITIAL INSPECTION: Please inspect your packaging upon arrival for any damage that may have occurred in shipping. If you see any damage take photographs, and call us immediately so we can file a claim if necessary.
- Page 2 Note, if for any reason your box arrives with damages to the exterior of the box, please take photographs and document this possible shipping damage. If upon further inspection any damage to the actual e-bike is found, please keep the box and contact us immediately at 757-635- 5160.
-
Page 3: Tools Needed For Assembly
For the time being, you can leave the three boxes inside and set up a flat, clean area where you're going to install your e-bike. The easiest way to remove the bike from the box is to grab the bike by the rear wheel rim and the frame, lifting it straight up until it clears the box itself. - Page 4 1) After everything has been removed from the original package, we are now going to begin the installation of your new e-bike. Start out by opening your component box, which should be the second largest box that you received in your package. This is what you will find inside: •...
- Page 5 Steer Dust Cap Top Cap The two bearings in your component box Notice the 45 degree angle facing up 2) The first thing that we're going to install is your front fork and steering system. Locate the black bottom bearing seat and slide onto the fork steering stem, all the way to the bottom of the steering tube.
- Page 6 Bearing Beveled side up into steer Beveled side down into headset cup 4) Now that your bearings are properly in place, insert your fork into the bottom of the headset cup on the head tube. An important note is to make sure your braking system for the front fork is located on the left side of your frame if you were in a riding position.
- Page 7 6) Now locate the four black spacers (each 10mm tall) and slide 3 or 4 (depending on how high you want your handlebars) onto the steer, directly on top of the dust cap. 7) Your stem (or handlebar mount if you aren't familiar with that term), has a slight angle which should be facing up.
- Page 8 Top Cap Secure Allen Nut Small Finishing Cap 8) Next, it's time to install your handlebars onto your stem. Unfasten the four allen nuts located on the end of your stem (facing away from your frame) and use the lines on your handlebars for an aid in lining them up with your stem.
- Page 9 wire coming out (for your motor connection). Notice how you have a smooth spacer and a lock tab spacer on each side of your axle. Smooth Spacer Lock Tab Spacer The lock tab spacer should sit outside of the smooth spacer, and should point down towards the bottom of the fork, facing away from the wheel, matching on both sides of the axle.
- Page 10 2. Add Nipple Washer 1. Flat Washer goes on inside Axle Nipple facing out to match both sides all the way against the hum in order to slide up into bottom of drop-out to lock drop out into place. 4. Insert Lock Ring Bolt into small hole and 3.
- Page 11 Left Side of Wheel With Locking Plate 10) It's time to install your seat (or saddle) on your new e-bike. Take the seat post and seat which we located in your component box in the beginning. On your frame, you'll see a QR (quick release) seat post clamp.
- Page 12 Bottom Bracket Top Bracket Seat/Saddle Secured Unfastened QR Seat post Clamp Fastened QR Seat post Clamp 11) Next thing were going to install is going to be your display and your controller, which was in a little brown box located inside of your components box. For this, you’re going to need your small 3 mm allen key.
- Page 13 Installed controller and Display 12) In your package you found a loose cable which goes to your front brake, which is what we're going to be installing now. Locate the end of the cable that has the little cylindrical metal piece. Squeeze your front brake (left) and place that gray metal piece into the designated hole on the brake (shown below).
- Page 14 Pull the metal wire through the slot on the brake and black metal mechanism, hand fastening it to the brake itself. 13) Pull the wire down alongside the fork and into the same piece which you found on your front brake on the handlebars. On the back of your Avid BBS Disc Caliper, you should find and allen nut with a metal washer underneath.
- Page 15 15) Now that everything is installed on your new e-bike, it’s time to tie up the loose ends. All of your cables can be zip tied to the designated areas that run alongside the frame of your bike.
- Page 16 17) You can now take your battery out of the box and install it onto the battery mount located on the bottom center of your frame. Before powering up your e-bike and taking it for a ride, it’s important to re-check the assembly and make sure that everything is properly fastened and secured.