Profile The smart WiFi plug is controlled via an APP installed in an Android or iOS smart phones or tablets, user can local or remote turn ON/OFF the device with WiFi signal and telecom mobile network signal provided and internet access be available. Users’apparatus can be powered through this plug, so that it can be controlled and monitored with the APP installed.
1.3 Diagram of how the plug is connected 1.4 Features 2. Safety Precautions ● To avoid any risk of unexpected harm or injury or damage to the smart WiFi plug, please read the manual thoroughly before operation and keep it carefully for future reference. Users should always comply with the safety precautions.
● This device is designed for indoor use only, it shall not be squeezed or impacted violently. It should be situated away from those devices or environment with excessive hot, cold, humid, wet, strong magnetic, strong electromagnetic interference (EMI), strong ultra-violet radiation, high static, high voltage or flammable, explosive materials.
Page 6
4.1 Function descriptions Function Details When output power turn on, LED turn on, WiFi indicator output power turn off, LED turn off also. 1.In need to manually power control, once press the button to turn on, twice press to off. 2.To reset factory default, press the button about 5 seconds till LED flash rapidly.
5. Install Guide The following hardware devices are necessary before configuration Properly functional WiFi router. APP devices like mobile phone, tablet etc(Android and IOS). 6. Configurations steps 6.1Firstly, download the APP onto your APP devices like mobile phone or tablet, Scanning the following QR code, and download it directly.
Page 8
Some QR code APP might not be able to recognize the above 6.1.2 of QR code. Please change another APP any try again. Check whether mobile phone or tablet is connected to a WiFi router properly as shown in the following figure. Please noted the interface and function of mobile phone or tablet may be different.
Page 9
Direct or AP mode: The plug is set to hotspot (AP) mode 6.3.2 first, a mobile phone or tablet PC is directly connected to AP of the plug, therefore, remote control the WiFi plug as follows: Client mode: Please reset the WiFi plug to factory defaults at the first time using or the WiFi network is changed.
Page 10
Depending on the status of the current WiFi network, the whole 6.5.1 configuration process takes about 3 ~ 30 seconds. If the connection is successful, the APP interface displays" A new device is added" or "Some devices are online, no newly-added device founded". New device is added : means new equipment is successfully 6.5.2 added.
Page 11
Several devices may try to connect the router at the same time. 6.5.4.7 Unplug the WiFi plug for about 10 seconds, then plug it into a socket to power up again, if it is still abnormal, rest it to Factory Settings. After a device is successfully added, goes back configuration 6.5.5 page, find the WFiPlug“...
Page 12
the current mobile phone or tablet and WiFi plug are Internet : connected via some extra internet network loops rather within a router coverage, the following figure shows the topology. it means the current mobile phone or tablet and WiFi plug are Off-line : unsuccessfully connected, the plug can be controlled.
Page 13
Control over Internet rather than LAN mode. 6.6. Connect the mobile phone or tablet to power plug via different WiFi 6.6.1 or cell phone network, exit the Settings menu. Enter into "Equipment list" as shown in following figure. Depends 6.6.2 WiFi signal or network condition , it may take about 5 seconds to 3 minutes to have "internet"...
“Weconn****, exit setting page after successful connection, further operation can be proceeded. It is strange to show about 1 minute delay for IOS system to have Note: a tickle mark to indicate a successful WiFi connection, well, evens so, you be able to enter the APP and proceed normal operation before that time.
12. FAQ WiFi control app going crashed? 12.1. Answer : Please cancel the WiFi plug power supply for about 10 seconds, and then re energized。 Reset the WiFi plug。 Cannot log in the app? 12.2. Answer : Check whether your APP meets Android and IOS operating system。...
General Jack Technology Co.,Ltd THE AREA OF ADMINISTRATION OF LANGBEI.
Page 19
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.