Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Prinics WU5108
- Page 1 WU5108 802.11 b/g/n Wireless LAN USB2.0 Module User’s Manual...
-
Page 2: Regulatory Statements
REGULATORY STATEMENTS FCC Certification The United States Federal Communication Commission (FCC) and Canadian Department of Communications have established certain rules governing the use of electronic equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interface, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 3 CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Federal Communication Commission (FCC) Radiation Exposure Statement This EUT is compliance with SAR for general population/uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and had been tested in accordance...
- Page 4 1. Introduction The WU5108 is an IEEE802.11b/g/n mini-size USB module that can connect the BP300 printer equipped with a USB Pin Connecter (Figure 2-1). The module has a core WiFi chipset, AR9271 which is produced by Atheros Communications, Inc. The WU5108 delivers reliable, cost-effective, feature rich wireless connectivity at high throughput from an extended distance.
- Page 5 Storage Humidity P : 10% to 95% Non-Condensing Power Standard USB Power DC 5V Requirement Power Input Printer Type : Soldering with a connector between the module and the Printer(BP300) Figure2-1 Method <Figure 2-1> Connection between WU5108 and Main PCB...
-
Page 6: Block Diagram
This exterior label shall be: "Contains FCC ID: PO5WU5108” 3. Block Diagram The WU5108 module consists of Main Chipset, AR9271 and peripheral parts (Fiqure3-1). It communicates with an external Main Printer PCB by using standard USB2.0 interface (Fiqure2-1). -
Page 7: Installation
When the printer has Power-ON, the module has 5V power from the printer PCB via USB connector (Figure4-1). <Figure 4-1> BP300 Printer System Block Diagram Main WU5108 Module Flash(4MB) DC1250 (ARM9Core) USB2.0 Connector... - Page 8 5. WU5108 Setup The WU5108 module in BP300 printer will be set up via the Android & iPhone application (Bolle Photo Air) to use a wireless printing. The module supports the securities – WPA, WPA2, and WEP64/128. The application program can check the each security one by one to connect to the Router.
- Page 9 3. The iPhone application sends the setting data to the printer via the Phone’s USB 2.0 cable 4. The printer gets the setting data and run the WU5108 Driver to search the Router. If the module connect to the Router, it sends the success message to the Main CPU(DC1250), and then the Main CPU sends the message to the Smart phone.
- Page 10 3. The Android Phone application sends the setting data to the printer via the Phone’s USB 2.0 cable. The printer gets the data and run the WU5108 Driver to search the Router. If the module connect to the Router, it sends the success message to the Main CPU(DC1250), and then the Main CPU sends the message to the Smart phone.
- Page 11 <How to work for Printing via WU5108> The printer has the WU5108 module in the case. The printer(BP300) can print an image via a wireless Router getting the image from the phone. <Figure 5-1> Interface between Printer and Smart Phone 1.
- Page 12 2. The application sends a command to list up what printers are available to print. The WU5108 Module is already ready to get the image from the phone via a router. If it gets the image, it sends to the Main CPU to process to print.
Need help?
Do you have a question about the WU5108 and is the answer not in the manual?
Questions and answers