Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Quick Start Manual
Advertisement
Table of Contents
Related Manuals for NeuroDigital Avatar VR
Summary of Contents for NeuroDigital Avatar VR
- Page 1 Quick Start Guide BY NEURODIGITAL TECHNOLOGIES S.L. DEVELOPMENT KIT - VERSION 1.1 - NOVEMBER 2017 AVATAR VR - QUICK START GUIDE...
- Page 2 Graphics Card NVIDIA GTX 970 / AMD R9 290 equivalent or greater Processor Intel i5-4590 equivalent or greater Memory 8GB + RAM Input 3x USB 3.0 ports Output Compatible HDMI 1.3 video output Bluetooth 4.0 Dual Mode for wireless operation AVATAR VR - QUICK START GUIDE...
-
Page 3: Table Of Contents
Avatar VR parts Connecting the TrackBand Calibrating the Gyroscopes Put the glove on Put the TrackBand on Using Avatar VR by Bluetooth Using Avatar VR by USB Color code Calibrating in demo Removing the glove AVATAR VR - QUICK START GUIDE... -
Page 4: Package Contents
Remove the contents from the box carefully. If any part is missing or damaged, please contact us at support@neurodigital.es The kit contains the following: USB Cable Avatar VR (Left, right or both depending on your order) TrackBand3, TrackBand2 or both depending on your order... - Page 5 AVATR VR PARTS IMU Sensors Actuators Power Button USB Port Li-Po Battery Breathable areas Conductive zones TrackBand The fabric composition is 80% polyamide with 20% elastomer. AVATAR VR - QUICK START GUIDE...
-
Page 6: Connecting The Trackband
CONNECTING THE TRACKBAND Link the TrackBand´s wrist connector to the glove as indicated. Wrist Link AVATAR VR - QUICK START GUIDE... -
Page 7: Calibrating The Gyroscopes
Press the button on the right side of the plastic cover to turn on Avatar VR. After that, you will see the LED blinking between blue-green colours. Once this process has finished, the device is calibrated. Don’t move anything till the light changes to blinking blue. Button AVATAR VR - QUICK START GUIDE... -
Page 8: Put The Glove On
PUT THE GLOVE ON Please be careful during handling as there is wiring inside the Avatar VR glove that needs to be placed correctly and not damaged. Start putting the glove on by gently looking for the finger holes while keeping a straight and steady hand and slowly introducing the glove. - Page 9 Test the fit to make sure everything feels as natural as possible. Gestures like pinching or grabbing should feel natural while allowing the respective grey zones (conductive fabric) to make contact. AVATAR VR - QUICK START GUIDE...
-
Page 10: Put The Trackband On
PUT THE TRACKBAND ON Colocate the TrackBand elements in order as shown in the picture below. Chest TrackBand Arm TrackBand Wrist TrackBand AVATAR VR - QUICK START GUIDE... -
Page 11: Using Avatar Vr By Bluetooth
USING AVATAR VR BY BLUETOOTH Do not connect any micro-usb cable from Avatar VR to your computer. Enable Bluetooth visibility: Do the “pinch” gesture for 2 second while you see a cyan light flicking and feel a short vibration. A permanent cyan light will confirm the Bluetooth is visible and ready to be paired within 2 minutes. - Page 12 Pair the device with your PC: Open the Bluetooth settings tab in your PC. Avatar VR should now appear as an accessible device. Pair with the device and wait until the pairing process finishes. It is mandatory to close this settings tab once it is paired.
- Page 13 Suite software and click on the “Bluetooth” button, then select the device you just paired. In a few seconds, it will be connected. (The ND Suite is required for Avatar VR to communicate with your PC. To download the lastest version of the installer, go to http:// www.neurodigital.es/dev/downloads/)
-
Page 14: Using Avatar Vr By Usb
Check the device in ND Suite: Open the ND Suite software and check that the device appears as connected. (The ND Suite is required for Avatar VR to communicate with your PC. To download the lastest version of the installer, go to http://www.neurodigital.es/dev/downloads/). -
Page 15: Color Code
COLOR CODE Avatar VR has a LED indicator that shows the state by means of a color code: If it is red (except while switching on) it tells us there is a problem, whether in functioning, low battery (in this case, it flashes), or it has stayed in an undetermined state (remains steady red until the power is switched off and on). -
Page 16: Calibrating In Demo
CALIBRATION IN DEMO When indicated, place your arms in front of you at a 90º angle for a few seconds until prompted to PLAY. IMPORTANT: The calibration pose can vary depending on the demo. AVATAR VR - QUICK START GUIDE... -
Page 17: Removing The Glove
Please be patient as this is the most critical step. You must be very careful as to not damage the glove’s electronics. Gradually remove the glove until you can release your gloved hand completely, without putting any significant strain on any part of the glove. AVATAR VR - QUICK START GUIDE... - Page 18 NEURODIGITAL TECHNOLOGIES S.L. NeuroDigital Technologies S.L., C/ Prolongación Camino de la Goleta, 2. Edf. La Celulosa I. Planta 1. 7B. 04007. Almería. Spain. Phone: + 34 950172762 AVATAR VR - QUICK START GUIDE...